Instruction/ maintenance manual of the product 7153-C Ingersoll-Rand
Go to page of 11
OPERATOR’S MANUAL SECTION M10 MANUAL 43 Released: 5/79 INCLUDING: OPERATION, INSTALLATION & MAINTENANCE “22” SERIES SHORT GRINDERS Revised: 1 O-20-95 Form: 1566-2 Models: 7149-C, 7153-C, 7235-C and 7236-C READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS EQUIPMENT.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY. m Turn off air supply and disconnect air supply hose before installing, removing or adjusting any accessory on this tool, or before performing any maintenance on this tool. Air powered tools can vibrate In use.
ROUTINE LUBRICATION REQUIREMENTS Ml0 43 Lack of or an excessive amount of lubrication will affect the perfor- mance and life of this tool. Use only recommended lubricants at below time intervals: EVERY 8 HOURS OF TOOL OPERATION - Fill lubricator reser- voir of recommended F.
The grinder models listed in the model identification table above arefurnished with collet assembly 41753-3 (1/4”capacity) as standard equipment and are intended for use with mounted wheels and shall not be used with othertype grinding wheels unless a proper wheel guard, recommended by the grinder manufacturer, is attached to thegrinder.
GRINDING WHEEL MOUNTING INSTRUCTIONS M10 43 Disconnect air supply from grinder or shut off air supply and exhaust (drain) air line of compressed air before mounting or removing any abrasive wheel or wire brush, or otherwise performing maintenance or service to the tool.
DISASSEMBLY AND ASSEMBLY OF TOOLS Disconnect air supply from tool or shut off air supply and exhaust (drain) line of compressed air BEFORE performing maintenance or service to tool. Before starting to disassemble or assemble this tool (any part or completely), be sure to read “Inspection, Maintenance and lnstal- lation” section.
MOTOR SECTION M10 43 DISASSEMBLY Remove motor from housing (see page 6). Grasp cylinder in one race of bearing. Assemble cylinder over rotor, aligning air inlets of hand and tap threaded end of rotor with a soft face hammer; motor cylinder and end plate and roll pin (Y17B-20) with hole in end will come apart.
HEAD SECTION DISASSEMBLY ASSEMBLY Remove valve plug (30600) and valve components can be re- moved from head. To remove lever throttle, remove roll pin (Y178-28). To remove button throttle, remove roll pin (Y178-212). Assemble “O” ring (Y325-7) to valve stem.
ACCES 41753-( ) 3-PIECE COLLET ASSEMBLY COLLET SUE COLLET , ASSEMBLY NO. INSERT NO. , 41753-I 1/8” 41750-1 41753-2 3/16 41750-2 41753-3 1/4” 41750-3 41753-11 3 mm 41750-11 41753-12 6 mm 41750-12 COLLET NUT - 41751 COLLET NUT DIA. - 3/4” COLLET BODY - 41752 COLLET BODY DIA.
TROUBLE SHOOTING LISTED BELOW ARE SOME OF THE MOST COMMON CAUSES FOR THE GRINDER TO MALFUNCTION. MALFUNCTIONS BEYOND THE SCOPE OF THIS MANUAL SHOULD BE BROUGHT TO THE ATTENTlON OF YOUR ARO REPRESENTATIVE OR RETURN THE TOOL TO THE FACTORY FOR REPAIR. CONDITION LOW SPEED AND POWER OR GRIND- ER WILL NOT RUN.
Part of worldwide Ingersoll-Rand.
An important point after buying a device Ingersoll-Rand 7153-C (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Ingersoll-Rand 7153-C yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Ingersoll-Rand 7153-C - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Ingersoll-Rand 7153-C you will learn all the available features of the product, as well as information on its operation. The information that you get Ingersoll-Rand 7153-C will certainly help you make a decision on the purchase.
If you already are a holder of Ingersoll-Rand 7153-C, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Ingersoll-Rand 7153-C.
However, one of the most important roles played by the user manual is to help in solving problems with Ingersoll-Rand 7153-C. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Ingersoll-Rand 7153-C along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
