Instruction/ maintenance manual of the product Saver Bath Walls American Standard
Go to page of 7
7547 48-1 00 Re v . C P roduct names listed herein are tr ademarks of AS America Inc. © AS America Inc. 201 2 NO TE: T ak e extr a care in handling the fr ont surfaces of the walls. Use only non-abr asive c loths to av oid scr atching. Thank you for selecting American Standard – the benchmark of fine quality for over 100 years.
2 7547 48-1 00 Re v . C Installation for use with t ub Model# 2647 .202 The studs should be located as sho wn to pr oper ly support walls. P ro vide additional studs where illustrat ed.
3 7547 48-1 00 Re v . C 1 2 INST ALLA TION PROCEDURES: If you plan to install a bath/shower door , a 1 x 4 must be installed in the pocket on the back of both side walls. A) Cut one end of the 1 x 4 to 45° as shown. (Fig.1) Then cut the 1 x 4 to a length of 57-1/2".
4 7547 48-1 00 Re v . C 3 A) Apply a bead of tub surround adhesive down each stud that will come in contact with the back panel being sure to stay below the line you marked. You do not need to apply adhesive to the corner studs. B) Lay a bead of sealant along tub ledge.
7547 48-1 00 Re v . C 5 5 A) Apply a bead of tub surround adhesive down each stud that will come in contact with the side panels being sure to stay below the line previously marked. B) Lay a bead of sealant along side panel mating surface and tub ledge.
7547 48-1 00 Re v . C 6 7 6 Install temporary braces to hold the center of the back and side panels tight to the studs for approximately 24 hours while adhesive sets. Add cushioning between panels and braces to prevent scratching the panels. When installing greenboard, position drywall screws above the top nailing flange.
7547 48-1 00 Re v . C 7 POST INS T ALLA TION CLEAN-UP Remo ve all construction debris. Tile grout can be r emov ed with a wooden popsicle stick or t ongue depressor . Do not use wire brushes or any other met al implement on surface. P ost installation clean-up generall y can be completed using warm wat er and liquid dishwashing deter gent.
An important point after buying a device American Standard Saver Bath Walls (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought American Standard Saver Bath Walls yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data American Standard Saver Bath Walls - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, American Standard Saver Bath Walls you will learn all the available features of the product, as well as information on its operation. The information that you get American Standard Saver Bath Walls will certainly help you make a decision on the purchase.
If you already are a holder of American Standard Saver Bath Walls, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime American Standard Saver Bath Walls.
However, one of the most important roles played by the user manual is to help in solving problems with American Standard Saver Bath Walls. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device American Standard Saver Bath Walls along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
