Instruction/ maintenance manual of the product PM-3200 Impex
Go to page of 26
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Identifier Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model PM-3200 Retain This Manual for Reference 110525 OWNER'S MANUAL PLATINUM MARCY HOME GYM PM-3200 IMPEX ® INC.
TABLE OF CONTENTS BEFORE YOU BE GIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES ...................................................................……….. 2 HARDWARE PACK ……….
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipm ent. Be sure to read the entire manual before you assemble or operate your machine.
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Base Frame and Upper Frame. If the labels are missing or illegible, please call customer ser vice at 1-800-888-8899 for replacements. Apply the labels in the location shown.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5.
HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 6.
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches, two Allen Wrenches, and one Philips Screwdriver. NOTE: It is strongly recommended this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.
DIAGRAM 1 8.
STEP 2 (See Diagram 2) A.) Do not tighten Nuts and Bolts until instructed to do so. B.) Slide the 14 Weight Plates (#34) onto the Guide Rods (#13). Make sure the deep grooves on the Plates are all facing down and toward back of the machine.
DIAGRAM 2 10.
STEP 3 (See Diagram 3) A.) Attach the Front Press Base (#6) to the U pper Frame (#4). Secure it with one 6 1/8” Front Press Axle (#37), one Ø ¾” Washer (#84), one Ø ¾” Lock Washer (#88), one M10 x 1” Allen Bolt (#73), and one Ø 2” End Cap (#47) on each end of the Axle.
DIAGRAM 3 12.
STEP 4 (See Diagram 4) A.) Attach the Main Seat Support (#1) to the Front Vertical Frame (#3). Secure it with two M10 x 3 ¾” Carriage Bolts (#79), one 4 ¾” x 1 ¾” Bracket (#22), two ¾” Washers (#84), and two M10 Aircraft Nuts (#83). B.
CABLE LOOP DIAGRAM 14.
STEP 5 (See Diagram 5 & Cable Loop Diagram) A.) Attach the 118” Upper Cable (#59) to the opening on the front of the Upper Frame (#4). Note : The Ball Stopper on the cable should be underneath the Frame. B.) Attach a Pulley (#62) to the opening.
DIAGRAM 5 16.
STEP 6 (See Diagram 6 & Cable Loop Diagram) A.) Attach one end of the 110” Butterfly Cabl e (#61) onto the hook on the Right Butterfly Base (#7).
DIAGRAM 6 18.
STEP 7 (See Diagram 7 & Cable Loop Diagram) A.) Attach the 157” Lower Cable (#60) to the opening on the bottom of the Leg Developer (#11). B.) Attach a Pulley (#62) to the opening. Secu re it with one M10 x 2 ½” Allen Bolt (#69), two Ø 7/8” x Ø 5/8” Bushings (#44), and one M10 Aircraft Nut (#83).
DIAGRAM 7 20.
STEP 8 (See Diagram 8) A.) Attach a Chain (#66) to the Lower Cabl e (#60) by using a Hook (#67). Attach the Shiver Bar Handle (#19) to the Chain by us ing another Hook. Adjust the length of the Chain to obtain the desired Arm Curl exerci se. Replace Shiver Bar Handle with Ankle Strap (#68) for various exercises.
Set up the Lock Combination A.) The combination is pre-se t at 0-0-0 by the factory. B.) Turn the dials to 0-0-0 and ali gned to the Combination Set Up Line. C.) Pull out the shackle and turn 180 0. D.) Press down on the shackle. E.) Turn the dials (aligned to the Combination Set Up Line) to your desired combination.
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Main Seat Support 1 2 Rear Base Frame 1 3 Front Vertical Frame 1 4 Upper Frame 1 5 Base Frame 1 6 Front Press Base 1 7 Right Butterfly Base 1 58 Plastic Ring 2 .
PM3200 WEIGHT RESISTANCE CHART WEIGHT PLATE Station 1 2 3 4 5 6 7 8 9 Front Press 30 42 54 66 78 90 102 114 126 Lat Pull 30 40 50 60 70 80 90 100 110 Butterfly 15 20 25 30 35 40 45 50 55 Low Pulley 30.
IMPEX ® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX ® ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two y ears on the Frame from the date of purchase. This warranty extends only to the original purchaser.
An important point after buying a device Impex PM-3200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Impex PM-3200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Impex PM-3200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Impex PM-3200 you will learn all the available features of the product, as well as information on its operation. The information that you get Impex PM-3200 will certainly help you make a decision on the purchase.
If you already are a holder of Impex PM-3200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Impex PM-3200.
However, one of the most important roles played by the user manual is to help in solving problems with Impex PM-3200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Impex PM-3200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
