Instruction/ maintenance manual of the product MWM-1840 Impex
Go to page of 29
NOTE: Please read all instructions carefully before using this product Table of Contents Safety Notice Hardware Pack Assembly Instruction Parts List Resistance Chart Warranty Ordering Parts Model MWM-1840 Retain This Manual for Reference 101015 OWNER'S MANUAL MARCY ® MWM-1840 HOME GYM IMPEX ® INC.
TABLE OF CONTENTS BEFORE YOU BE GIN....................................................................................……….. 1 IMPORTANT SAFETY NOTICES ...................................................................……….. 2 HARDWARE IDENTI FIER.
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipm ent. Be sure to read the entire manual before you assemble or operate your machine.
WARNING LABEL PLACEMENT The w arning labels show n here have been placed on the Middle Stabilizer and Upper Frame. If the labels are missing or illegible, please call customer service at 1- 800-888-8899 for replacements. Apply the labels in the location show n.
HARDWARE PACK NOTE: The follow ing parts are not draw n to scale. Please use your own ruler to measure the size. 4.
HARDWARE PACK NOTE: The follow ing parts are not draw n to scale. Please use your own ruler to measure the size. 5.
HARDWARE PACK NOTE: The follow ing parts are not draw n to scale. Please use your own ruler to measure the size. 6.
ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that this machine to be assembled by two or more people to avoid possible injury. STEP 1 (See Diagram 1) A.) Place the Middle Stabilizer (#2) on flat surface.
STEP 2 (See Diagram 2) A.) Insert the two Guide Rods (#11) into the holes on the Middle Stabilizer (#2). Secure each Guide Rod with one M10 x 1” Allen Bolt (#81) and two ¾” Washers (#91) from the bottom. Slide two Ø 2 ¼” x 1” Guide Rod Rubber Bumpers (#39) onto the two Guide Rods from top to bottom.
DIAGRAM 2 9.
STEP 3 (See Diagram 3) A.) Slide 14 Weight Plates ( #42) onto the Guide Rods (#11). Make sure the deep grooves on the Weight Plates all face the back of the machine and downw ard. B.) Align the holes on the Weight Plates. Insert a Selector Rod (#21) through the center hole.
STEP 4 (See Diagram 4) A.) Place the Upper Frame (#1) onto the Vertical Frame (#4). B.) Attach the brackets on the Upper Frame to the two Guide Rods. Secure the Guide Rods to the brackets with two M10 x 1” Allen Bolts (#81) and Ø ¾” Washers (#91).
DIAGRAM 4 12.
STEP 5 (See Diagram 5) A.) Attach the Front Press Base (#8) to the Upper Frame (#1). Secure it with one 8 ½” Front Press Axle (#19), two Ø 1” Large Washers (#96), and two M10 Aircraft Nuts (#97). Do not over tighten the Nuts. B.) Insert the axle on the Left Butterfly (#9) th rough the open hole on Front Press Base from bottom.
DIAGRAM 5 14.
STEP 6 (See Diagram 6) A.) Attach the Left Dip Support (#28) into Ri ght Dip Support (#27) behind the Power Station Vertical Frame (#26). B.) Attach the holes on the bracket of Left & Right Dip Support to the hole on the Vertical Frame. Align the holes.
DIAGRAM 6 16.
STEP 7 (See Diagram 7) A.) Attach one Swivel Pulley Bracket (#17) to the open bracket on the back of Vertical Frame (#4). Secure it with one M10 x 2 ½” A llen Bolt (#76), two Ø ¾” Washers (#91), and one M10 Aircraft Nut (#97) . Do not over tighten the Nut and Bolt.
STEP 8 (See Diagram 8) A.) Attach the Power Station Arm Pads (#35) to the Right & Left Dip Support (#27 & #28). Secure each Arm Pad with two M8 x 2 ¾” A llen Bolts (#84) and two Ø 5/8” x 1” Curved Washers (#94). B.) Attach two Vertical Handles (#13) to Ri ght & Left Dip Support.
STEP 9 (See Diagram 9 & Cable Loop Diagram) A.) Attach the 127 ½” Upper Cable (#56) to the front open bracket under the Upper Frame (#1). B.) Attach a Pulley (#40) to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#74), two Ø ¾” Washers (#91), and one M10 Aircraft Nut (#97).
DIAGRAM 9 20.
STEP 10 (See Diagram 10 & Cable Loop Diagram) A.) Hook one end of the 98” Butterfly C able (#57) to Right Butterfly (#10). B.) Draw the Cable towards the right open Swivel Pulley Bracket (#17).
STEP 11 (See Diagram 11 & Cable Loop Diagram) A.) Attach the 159” Lower Cable (#58) to the opening bracket on Leg Developer (#7). B.) Attach a Pulley (#40) to the opening. Se cure it with one M10 x 2 ½” Allen Bolt (#76), two 1” x 5/8” Pulley Bushings (#52), and one M10 Aircraft Nut (#97).
23.
STEP 12 (See Diagram 12) A.) Connect Lat Bar (#14) to the Upper Cable ( #56) with two Hooks (#63) and one 15-link Chain (#55) when doing Lat Pull exercises. B.) Connect Shiver Bar (#15) to the Lower Cabl e (#33) use the two Hooks and the 15-link Chain from Lat Bar when doing Arm Curl exercises C.
Set up the Lock Combination A.) The combination is pre-se t to 0-0-0 by the factory. B.) Turn the dials to 0-0-0 and ali gned to the Combination Set Up Line. C.) Pull out the shackle and turn 180 0. D.) Press down on the shackle. E.) Turn the dials (aligned to the Combination Set Up Line) to your desired combination.
PARTS LIST KEY NO. DESCRIPTION Q’ty 1 Upper Frame 1 51 Ø 1” x Ø ½” Bushing 2 2 Middle Stabilizer 1 52 Ø 1” x 5/8” Pulley Bushing 4 3 Base Frame 1 53 Combination Lock 1 4 Vertical Frame 1.
MWM1840 WEIGHT RESISTANCE CHART Weight Plate Leg Developer Front Press Butterfly Lat Pull Low Pulley 1 30 31 15 30 30 2 40 44 20 40 40 3 50 57 25 50 50 4 60 70 30 60 60 5 70 83 35 70 70 6 80 96 40 80 .
IMPEX ® INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX ® ") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two y ears on the Frame from the date of purchase. This warranty extends only to the original purchaser.
An important point after buying a device Impex MWM-1840 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Impex MWM-1840 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Impex MWM-1840 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Impex MWM-1840 you will learn all the available features of the product, as well as information on its operation. The information that you get Impex MWM-1840 will certainly help you make a decision on the purchase.
If you already are a holder of Impex MWM-1840, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Impex MWM-1840.
However, one of the most important roles played by the user manual is to help in solving problems with Impex MWM-1840. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Impex MWM-1840 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
