Instruction/ maintenance manual of the product IMBE40890 Image
Go to page of 18
QUESTIONS? As a manufacturer , we are com- mitted to providing complete customer satisfaction. If you have questions, or find that there are missing or damaged parts, we will guarantee you complete satisfaction through direct assis- tance from our factory .
2 W arning Decal Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 W ARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
4 Weight Carriage Weight T ube High Pulley Station Low Pulley Station Lat Bar Weight Rest Safety Spotter Curl Pad Right Side Left Side Note: The terms Òright sideÓ and Òleft sideÓ are determined relative to a person sitting on the bench; they do not correspond to right and left on the drawings in this manual.
5 Part Identification ChartÑModel No. IMBE40890 R0999A M10 Nylon Locknut (1 1)Ð29 M8 Nylon Locknut (13)Ð2 M6 W asher (30)Ð4 M6 x 16mm Screw (3)Ð6 M8 x 64mm Bolt (43)Ð1 M6 x 38mm Screw (4)Ð4 Pro.
6 1. Before beginning assembly , make sure that you understand the information in the box above. Note: Some of the parts described in the assem- bly steps may be pre-assembled. Press a 2Ó Square Inner Cap (17) into the indicated end of the Right Stabilizer (26).
3. Align the holes in a 4-hole Support Plate (16) with the holes in the Right Upright (2). Insert four M10 x 72mm Bolts (68) into the Support Plate and the Right Upright. Make sure that the Bolts are inserted from the direction shown. Align the holes in another 4-hole Support Plate (16) with the holes in the Left Upright (1).
8 4. Snap a Carriage Bushing (56) into the Weight Stop (53). Slide both parts onto the Rear Upright (9), mak- ing sure that the Carriage Bushing (56) is on top. Attach the parts to the indicated hole in the Rear Upright with an M8 x 68mm Bolt (60) and an M8 Nylon Locknut (13).
9 7. The Upper Cable (45) was attached to the Weight Carriage in step 5. Wrap the Upper Cable around a Pulley (35) in the direction shown. Attach the Pulley (35) and a Cable T rap (61) to the indicated hole in the T op Frame (7) with an M10 x 108mm Bolt (34), a 15.
10 1 1. Locate the Lower Cable (39) and note that it has a ball/loop on one end and a loop only on the other . See drawing 1 1a. Route the end of the Lower Cable with the loop through the cable guide on the outside of the Right Upright (2). See drawing 1 1.
11 13. Insert two M10 x 68mm Bolts (33) into the 2-hole Support Plate (70), the Front Leg (19), and the brack- et on the Bench Frame (5) as shown. T ighten an M10 Nylon Locknut (1 1) onto each Bolt. 13 33 11 11 5 70 19 14. Align the bracket on the Bench Frame (5) with the holes in the center of the Crossbar (20).
12 17. Press a 3/4Ó Round Inner Cap (54) into each end of the three Pad T ubes (38). Press a Foam Pad (10) onto one end of a Pad T ube (38). Insert the Pad T ube into one set of holes in the bracket on the Front Leg (19). Press a Foam Pad onto the other end of the Pad T ube.
13 21. Press 25.4mm Round Inner Caps (37) into the Weight Rests (21, 66) and the Safety Spotters (63, 69). Insert the Weight Rests (21, 66) into the Uprights (1, 2). Make sure that the Weight Rests are at the same height and that the locking clips are hooked around the Uprights.
14 ADJUSTING THE FOAM P ADS The Foam Pads (10) inserted into the bracket on the Front Leg (19) can be adjusted to two different positions. T o do this, pull one Foam Pad off the Pad T ube (38). Move the Pad T ube to the other hole in the bracket on the Front Leg.
15 A TT ACHING WEIGHTS T O THE WEIGHT CARRIAGE T o use the upper or lower pulley stations, slide the desired amount of weight (not included) onto the weight tube of the Weight Carriage (47). Secure the weights with Weight Clips (50). 47 Weight T ube W ARNING: Do not place more than 150 pounds on the Weight Carriage.
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of the user Õs manual for information about ordering replacement parts. Key No. Qty . Description Key No. Qty . Description Part ListÐModel No.
11 11 6 11 11 13 17 60 68 33 25 38 10 54 54 39 31 45 35 40 34 11 6 31 34 11 6 31 11 6 11 6 67 6 67 6 11 6 45 55 11 57 11 35 62 35 62 56 56 12 69 37 32 47 12 61 61 61 61 35 35 6 67 6 67 11 6 17 16 71 3.
Part No. 157727 R0999A Printed in China © 1999 ICON Health & Fitness, Inc. T o order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday , 6 a.m. until 6 p.m. Mountain T ime (excluding holidays).
An important point after buying a device Image IMBE40890 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Image IMBE40890 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Image IMBE40890 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Image IMBE40890 you will learn all the available features of the product, as well as information on its operation. The information that you get Image IMBE40890 will certainly help you make a decision on the purchase.
If you already are a holder of Image IMBE40890, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Image IMBE40890.
However, one of the most important roles played by the user manual is to help in solving problems with Image IMBE40890. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Image IMBE40890 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
