Instruction/ maintenance manual of the product PA 1100 Husqvarna
Go to page of 17
E E E E n n n n g g g g l l l l i i i i s s s s h h h h Sa w attachment P A P A 1100 Accessoir e de sciage P A P A 1100 Suplemento de sierr a P A P A 1100 Oper ator ′ s manual Manuel d’utilisa tio.
2 – English KEY T O SYMBOLS . Symbols W ARNING! The machine can be a dangerous tool if used incorrectly or carelessly , which can cause serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine .
English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Husqvarna AB has a policy of continuous product de velopment and therefore reserves the right to modify the design and appearance of products without prior notice. Long-term exposure to noise can result in permanent hear ing impairment.
4 – English SAFETY INSTR UCTIONS Cutting equipment This section describes how you can achie ve maximum clearing capacity and extend the lif e of the cutting attachment through correct maintenance and using the right type of cutting attachment. Only use cutting equipment recommended b y us! See the T echnical data section.
English – 5 SAFETY INSTR UCTIONS Chain • Saw chain pitch (inches). (The distance between three drive links, divided b y two .) • Drive link width (mm/inches) • Number of drive links. Sharpening y our chain and adjusting raker c learance General information on sharpening cutting teeth • Ne ver use a blunt chain.
6 – English SAFETY INSTR UCTIONS • Alwa ys file cutting teeth from the inside face outw ards. Reduce the pressure on the return stroke. File all the teeth on one side of the bar first. Then turn the saw o ver and file the remaining teeth from the other side.
English – 7 SAFETY INSTR UCTIONS 1 Undo the bar nut. 2 Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner . Tighten the chain until it does not sag from the underside of the bar . 3 Use the combination spanner to tighten the blade n ut while holding up the tip of the bar .
8 – English SAFETY INSTR UCTIONS 2 Check that the oil channel in the gear housing is clean. Clean if necessar y . 3 Check that the bar tip sproc ket turns freely . If the chain lubrication system is still not working after carr ying out the abov e checks you should contact y our ser vice workshop.
English – 9 SAFETY INSTR UCTIONS P ersonal pr otection • Alwa ys wear boots and other equipment described under the heading P ersonal protective equipment in the machine’ s Operator’ s Manual. • Alwa ys wear working clothes and heavy-duty long trousers.
10 – English SAFETY INSTR UCTIONS • Alwa ys slow the engine to idle speed after each working operation. Long per iods at full throttle without any load on the engine can lead to serious engine damage. • Alwa ys work at full throttle. • Let the engine drop back to idle speed betw een each cut.
English – 11 WHA T IS WHA T? What is what on the saw attac hment? (Saw attachment with shaft P A 1100) 11 9 1 2 8 6 5 4 10 7 13 12 14 15 3 11 1 Be vel gear 2 Chain lubrication adjustment screw 3 Sha.
12 – English WHA T IS WHA T? What is what on the saw attac hment? (Saw attachment without shaft P A) 10 8 1 2 7 5 4 3 9 6 12 11 13 14 10 1 Be vel gear 2 Chain lubrication adjustment screw 3 Harness .
English – 13 ASSEMBL Y Fitting the cutting head (Saw attachment with shaft P A 1100) • Fit the cutting head on the shaft so that the screw (A) is aligned with the hole in the shaft as shown. • Tighten screw A. • Tighten screw B . CA UTION! Make sure that the drive shaft inside the shaft engages with the cut-out in the cutting head.
14 – English ASSEMBL Y Adjusting the harness Y ou should alwa ys use the har ness with the machine to give maximum control ov er the machine and reduce the risk of f atigue in your ar ms and back. • Put on the harness. • Hook the machine onto the harness suppor t hook.
English – 15 TECHNICAL D A T A T echnical data Note 1: Equivalent sound pressure le vel is calculated as the time-weighted energy total f or sound pressure lev els under various working conditions with the follo wing time distr ibution: 1/2 idling and 1/2 max speed.
16 – English TECHNICAL D A T A EC-dec laration of conformity (Applies to Europe onl y) W e, Husqvarna AB, SE-561 82 Huskv ar na, Sweden, tel +46-36-146500, declare that this saw attachment from 2002.
´®z+H8r¶0_¨ 2004-02-05 ´®z+H8r¶0_¨ 1140248-26 20.
An important point after buying a device Husqvarna PA 1100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husqvarna PA 1100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husqvarna PA 1100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husqvarna PA 1100 you will learn all the available features of the product, as well as information on its operation. The information that you get Husqvarna PA 1100 will certainly help you make a decision on the purchase.
If you already are a holder of Husqvarna PA 1100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husqvarna PA 1100.
However, one of the most important roles played by the user manual is to help in solving problems with Husqvarna PA 1100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husqvarna PA 1100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center