Instruction/ maintenance manual of the product HDN10500 Husky
Go to page of 16
1 inch 23g Micr o Pin Nailer T able of Contents Description . . . . . . . . . . . . . . . . . . . . . 1 Unpacking . . . . . . . . . . . . . . . . . . . . . . 1 Safety Guidelines . . . . . . . . . . . . . . . . 1 Important Safety Information . . . . . .
GENERAL a. T o reduce the risks of electric shock, fire, and injury to persons, read all the instructions before using the tool. b. Be thoroughly familiar with the controls and the proper use of the equipment. Follow all instructions. Contact your Husky representative if you have any questions.
Never place hands or any other body parts in the fastener discharge area of the tool. The tool might eject a fastener and could result in death or serious personal injury . Never carry the tool by the air hose or pull the hose to move the tool or a compressor .
4 Operating Instructions Important Safety Instructions (Continued) SERVICE a. T ool service must be performed only by qualified repair personnel. b. When servicing a tool, use only identical replacement parts. Use only authorized parts. c. Use only the lubricants supplied with the tool or specified by the manufacturer .
5 HDN10500 OPERA TING INSTRUCTIONS (Continued) 3. Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the power source if a regulator fails, or 150 psi, whichever is greater . Use 1/4 inch air hose for runs up to 50 feet.
6 Operating Instructions www .chpower .com 6 Operating Instructions USER-MAINTENANCE INSTRUCTIONS (Continued) ASSEMBL Y PROCEDURE FOR SEALS When repairing a tool, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings.
7 HDN10500 Symptom Possible Cause(s) Corrective Action Air leaking at trigger valve area. O-Rings in trigger valve housing are damaged Replace o-rings Air leaking between housing and nose. 1. Damaged O-Rings 1. Replace o-rings 2. Damage to bumper 2. Replace bumper Air leaking between housing and cap.
8 Operating Instructions Limited Warranty - Husky 1 inch 23g Micr o Pin Nailer by Campbell Hausfeld 1. DURA TION: From the date of purchase by the original purchaser as follows: One (1) Y ear .
Índice Descripción . . . . . . . . . . . . . . . . . . . . . 9 Desempaque . . . . . . . . . . . . . . . . . . . . 9 Medidas de Seguridad . . . . . . . . . . . . 9 Instrucciones de Seguridad Importantes . . . . . . . . . . . . . . . . . . . . . 9 Componentes y Especificaciones de la Herramienta .
La herramienta puede crear chispas y provocar la ignición de polvo o vapores. c. Mantenga alejados a los observadores, niños y visitantes mientras hace funcionar la herramienta. Las distracciones pueden dar como resultado la pérdida del control de la herramienta.
11-Sp HDN10500 Instrucciones de Seguridad Importantes (Continúa) j. No clave ningún clavo encima de otro clavo. Esto puede hacer que el clavo se desvíe y golpee a alguien, o provocar que la herramienta reaccione y cause el riesgo de lesiones personales.
No opere la herramienta ni permita que otros la operen si las etiquetas de advertencia están ilegibles. Éstas se encuentran en el cargador o el cuerpo de la herramienta. No deje que la herramienta se caiga ni la tire. Ésto podría dañarla o convertirla en algo peligroso de usar .
Los aceites para herramientas neumáticas contienen solventes que pueden averiar los componentes internos de la herramienta. 3. Después de agregar aceite, haga funcionar la herramienta brevemente. Limpie todo exceso de aceite que salga del escape de la tapa.
Manual de Instrucciones de Operación INSTRUCCIONES DE USO Y MANTENIMIENTO ASSISTÊNCIA TÉCNICA Para mayor información en relación al funcionamiento o reparación de este producto, comuníquese con el concesionario de Husky más cercano a su domicilio.
15-Sp HDN10500 Problema Causa Solución Hay una fuga de aire en el área de la válvula del gatillo. Los anillos en O de la cubierta de la válvula del gatillo están dañados. Debe reemplazar los anillos en O Hay una fuga de aire entre la cubierta y la boquilla.
Manual de Instrucciones de Operación 16-Sp Garantía Limitada - Clavadora de Micro Puntillas de 1 pulg. calibre 23 de Campbell Hausfeld 1 DURACION: A partir de la fecha de compra por el comprador original tal como se especifica a continuación: Un (1) año.
An important point after buying a device Husky HDN10500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Husky HDN10500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Husky HDN10500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Husky HDN10500 you will learn all the available features of the product, as well as information on its operation. The information that you get Husky HDN10500 will certainly help you make a decision on the purchase.
If you already are a holder of Husky HDN10500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Husky HDN10500.
However, one of the most important roles played by the user manual is to help in solving problems with Husky HDN10500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Husky HDN10500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
