Instruction/ maintenance manual of the product The Kensington Hunter
Go to page of 17
www .HunterF an.com 1.888.830.1326 PA G E 7 PA G E 13 PA G E 14 PA G E 10 PA G E 5 PA G E 17 PA G E 6 30 inches 7 feet PA G E 2 What to Expect with Y our Installation Ceiling Br acket Installation Lad.
www .HunterF an.com 1.888.830.1326 M0001-01 • 08/03/12 • © Hunter F an Company 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring, use a qualied electrician. Y ou may need a friend to help you.
T ools Needed Po wer Drill (optional) Ladder 9/64” Drill Bit (optional) Screwdrivers Pliers Wire Strippers Mounting Options 1. Y ou will need a Longer Downrod sold separately 2.
1.888.830.1326 www .HunterF an.com 4 Mounting Options (c ontinued) Use Standard or L ow-Prole Mounting to hang the fan from a at ceiling by a standard downrod (included). Use Angled Mounting t o hang the fan from a vault ed or angled ceiling (see previous page).
1.888.830.1326 www .HunterF an.com C eiling Bracket Installa tion OFF Make sure all four (4) bumpers are still attached . F or angled ceilings, point opening toward peak.
www .HunterF an.com 1.888.830.1326 C eiling Bracket Installa tion (continued) Prepar ation 1.888.830.1326 www .HunterF an.com D I S C A R D K E E P ! Remove the shipping blocks from the motor . Sav e the ve scre ws. The y will be needed for blade iron installation.
1.888.830.1326 Downrod Slid e Slid e 1 2 3 4 5 6 7 8 9 10 Sold Separately Included Longer Downrod for angled ceilings or ceilings 10’ or higher Shorter Downrod for fans installed close to ceiling St.
KEEP! 8” 3/8” C U T & S T R I P (not to scale) Remove the pre-installed setscrew so that the downrod can be inserted. Hand tighten the downrod (at least 4-5 full turns) until it stops. The wires can be cut, but leave at least 8” extending from the top of the downr od.
1.888.830.1326 9 M0001-01 • 08/03/12 • © Hunter F an Compan y www .HunterF an.com Downrod (c ontinued) DO NO T PICK THE F AN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. Put the wires and do wnrod through the canopy .
www .HunterF an.com 1.888.830.1326 Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/ yellow stripe , or bare copper) coming from the ceiling , downrod, and hanging bracket.
www .HunterF an.com 1.888.830.1326 11 M0001-01 • 08/03/12 • © Hunter F an Compan y Canop y Lift the canopy into place so that the screw holes are aligned . Position the canop y so that, when lifted into place , the canopy ts into the hanging bracket as shown.
www .HunterF an.com 1.888.830.1326 Blades Y our blades are shielded with Dust Armor® which is a nanotechnology coating that repels dust. F or cleaning the fan, use soft brushes or cloths to prevent scratching . Cleaning agents ma y damage the nishes.
www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfwa y into the motor housing .
www .HunterF an.com 1.888.830.1326 Connect the plugs from the upper and lower switch housings . Mak e sure to line up the colored markings on the connectors. Partially install two of the switch housing screws found in the bag . Align the notches in the sides of the lower switch housing with the screws on the upper switch housing .
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! Install the bulbs into the sockets. When necessary , replace with bulbs of same wattage. No te: Glass shade styl e and number of lights may vary . See next page for fan opera tion instruc tions.
www .HunterF an.com 1.888.830.1326 M0001-01 • 08/03/12 • © Hunter F an Compan y 16 Maintenanc e & Cleaning The fan pull chain controls the speed: high, medium, low , and off . The light pull chain controls the light xture: on and off . T o switch the direc tion of air ow , mov e the reverse switch to the opposite position.
www .HunterF an.com 1.888.830.1326 M0001-01 • 08/03/12 • © Hunter F an Compan y 17 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • T urn the power off , support the fan carefully , and check that the hanger ball is properly seated .
An important point after buying a device Hunter The Kensington (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hunter The Kensington yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hunter The Kensington - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hunter The Kensington you will learn all the available features of the product, as well as information on its operation. The information that you get Hunter The Kensington will certainly help you make a decision on the purchase.
If you already are a holder of Hunter The Kensington, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hunter The Kensington.
However, one of the most important roles played by the user manual is to help in solving problems with Hunter The Kensington. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hunter The Kensington along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
