Instruction/ maintenance manual of the product Low Profile Plus Hunter
Go to page of 14
www .HunterF an.com 1.888.830.1326 Congratulations on purchasing your new Hunter® ceiling fan! It will provide comf or t and per formanc e in your home or ofce f or many years. T his installation and operation manual contains complete instructions for installing and operating your fan.
www .HunterF an.com 1.888.830.1326 M0010-01 • 11/02/12 • © Hunter F an Compan y 1.888.830.1326 1.888.830.1326 What t o Expec t with Y our Installation Know your wiring If you are unfamiliar with wiring, use a qualied electrician. Y ou may need a friend to help you.
www .HunterF an.com 1.888.830.1326 T ools Needed Ladder Po wer Drill (optional) 9/64” Drill Bit (optional) Screwdrivers If mounting to a support structure, you will also need these tools .
1.888.830.1326 www .HunterF an.com C eiling Bracket OFF Refer to warning w .1 on pg. 2 T o av oid possible elec trical shock, before installing y our fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
www .HunterF an.com 1.888.830.1326 C eiling Bracket (c ontinued) Prepar ation 1.888.830.1326 www .HunterF an.com Time Sav er Tip: Get a helper to insert grommets, found in the hardware bag , into the blades while you ’r e doing the next couple of steps.
www .HunterF an.com 1.888.830.1326 6 M0010-01 • 11/02/12 • © Hunter F an Company Hanging the F an While holding the wires out of the way , lif t the motor assembly and place the square hanger into the opening in the ceiling bracket. Be sure the ground wire attached to the hanger faces out of the large opening in the ceiling bracket.
www .HunterF an.com 1.888.830.1326 Wiring F R O M F A N F R O M C E I L I N G B R A C K E T F R O M F A N Using an orange wire connector from the hardware bag , connect the 3 grounding wires (green, green/ yellow stripe , or bare copper) coming from the ceiling , downrod, and hanging bracket.
www .HunterF an.com 1.888.830.1326 With a Phillips head screwdriv er , install the four motor housing screws f ound in the hardware bag . Tighten all four screws securely . Motor Housing Screw Holes Motor Housing Screw Indentation Notch Raise the motor housing up over the motor and ceiling bracket.
www .HunterF an.com 1.888.830.1326 Blades 9 M0010-01 • 11/02/12 • © Hunter F an Company Insert grommets found in the hardware bag into the holes in the blades, then secure each blade to a blade iron with screws found in the hardw are bag.
www .HunterF an.com 1.888.830.1326 F eed the wire plug through the center hole of the upper switch housing , then wrap keyhole slots around the screws and twist counterclockwise. Screw two (2) housing assembly screws from the hardware bag halfwa y into the motor housing .
www .HunterF an.com 1.888.830.1326 Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. Partially install two of the switch housing screws found in the hardw are bag. Align the notches in the sides of the lower swit ch housing with the screws on the upper switch housing.
www .HunterF an.com 1.888.830.1326 Light Kit (c ontinued) C ONGRA TULA TIONS! Y OU’RE DONE! Install a bulb into each of the sockets. When necessary , replace with bulbs of same wattage. No te: Glass shade style and numb er of lights may vary . See next page for fan opera tion instruc tions.
www .HunterF an.com 1.888.830.1326 M0010-01 • 11/02/12 • © Hunter F an Company 13 Maintenanc e, Oper ation & Cleaning The fan pull chain controls the speed: high, medium, low , and off . The light pull chain controls the light xture: on and off .
www .HunterF an.com 1.888.830.1326 M0010-01 • 11/02/12 • © Hunter F an Company 14 T roubleshooting Exc essive wobbling • Tighten all of the blade and blade iron screws until they are snug . • Use the provided balancing kit and instruc tions to balance the fan.
An important point after buying a device Hunter Low Profile Plus (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hunter Low Profile Plus yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hunter Low Profile Plus - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hunter Low Profile Plus you will learn all the available features of the product, as well as information on its operation. The information that you get Hunter Low Profile Plus will certainly help you make a decision on the purchase.
If you already are a holder of Hunter Low Profile Plus, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hunter Low Profile Plus.
However, one of the most important roles played by the user manual is to help in solving problems with Hunter Low Profile Plus. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hunter Low Profile Plus along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
