Instruction/ maintenance manual of the product 82048 Hunter Fan
Go to page of 21
43042-01 02/21/2008 1 FRANÇAIS Consulter la page 45 ENGLISH See page 2 ESP AÑOL V ea la p á gina 23 82048 T urino Bath V entilator with Light READ and SA VE THESE INSTRUCTIONS Installation Guide.
43042-01 02/21/2008 2 TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: PREVENT A TIVE MAINTENANCE A clean fan provides better service. Disconnect the power supply and clean the fan as listed below . TO CLEAN GRILLE: Use a mild detergent, such as dishwashing liquid, and a soft cloth.
43042-01 02/21/2008 3 D 95044-01-000 N 75184-01-133 L 97959-01-000 K 65219-01-000 J 77521-01-000 E 95029-01-000 A x4 F 75191-01-000 G 03242-07-133 I H 74508-03-133 98037-01-000 x2 O 97960-01-000 M 75729-01-000 P 77535-01-000 Check all the parts. If damaged, call 1-888-830-1326 for replacements.
43042-01 02/21/2008 4 Remove the motor/blower from the housing. Remove the pre-loaded screw tip covers. Back out the pre-loaded screw tips until flush with the side of the housing. Remove packing material. T urn off the power source. Before Installation Loosen screws.
43042-01 02/21/2008 5 7 G Pop out the first wiring access slug. Use second if needed. Insert the strain relief into the housing and secure with the washer .
43042-01 02/21/2008 6 5/8 1/2 A1 1 A13 A12 E Connect wires as shown. Pull wires through the strain relief. Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. New Construction – attaching to joist Screw pre-loaded screws into joist or framing.
43042-01 02/21/2008 7 0 0 0 0 0 0 0 0 0 A15 A18 A20 A19 A17 A16 F H I G E Connect wiring from the motor to the wiring cover plate. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing.
43042-01 02/21/2008 8 5/8 1/2 5/8 1/2 1/8" Bit Slide the mounting rails into brackets. Mark position of screws by using holes as a template. New Construction – suspended between joists Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock.
43042-01 02/21/2008 9 Connect wires as shown. T ighten screws. Pull wires through the strain relief. Insert screws, leaving space between the screw head and the joist.
43042-01 02/21/2008 10 Connect wiring from the motor to the wiring cover plate. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. T urn on the power source. Secure the motor by tightening the 2 screws.
43042-01 02/21/2008 11 8” 8.5” B26 C1 1 C12 B27 E1 Go to step on page 18 to attach grille. Existing Construction – accessible from above OR Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (8”x 8.
43042-01 02/21/2008 12 1/8" Bit 5/8 1/2 5/8 1/2 C13 C14 C15 C16 C17 C18 Drill a hole in the center of each outline. Insert screws, leaving space between the screw head and the joist. Screws are not provided. Attach the rails onto the screws. T ighten screws.
43042-01 02/21/2008 13 C19 C20 C21 T ighten the strain relief screws. Connect 4” duct and vent to the outside. T ape joints. If ducting does not fit securely , an adapter may need to be purchased. Pull wires through the strain relief. Connect wires as shown.
43042-01 02/21/2008 14 Secure the motor by tightening the 2 screws. T urn on the power source. T est the motor . If the motor does not run, check the plug connection. Install the wiring cover plate. Make sure all wiring connections are inside the box or under the wiring cover plate.
43042-01 02/21/2008 15 2 1 Existing Construction – accessible only from below Pull wires through strain relief . Remove an existing fan and check to make sure the opening is large enough to accommodate the new motor housing (8”x 8.5”). Move the housing into position above the ceiling.
43042-01 02/21/2008 16 D15 E D16 D17 D18 F G F H A Fan Motor Light 2 Pin Black Ground Green Bare Copper White Black Main Switch 1 (AC In) Black Switch 2 (AC In) Black Light *Option White White 3 Pin *Option Fan & Main Light T ogether Connect wiring from the motor to the wiring cover plate.
43042-01 02/21/2008 17 D19 D20 H I D21 D22 D23 E1 Go to step on page 18 to attach grille. T est the motor . If the motor does not run, check the plug con- nection. T urn on the power source. Reinstall the motor by inserting the tabs and pushing up into position.
43042-01 02/21/2008 18 E1 E3 E4 E5 E6 E2 K K J L Align posts A, B, C and D (stamped into motor housing) with posts A, B, C and D (stamped into light fixture). Slide light fixture over posts. Remove the strain relief bracket screw . Position the strain relief bracket under the motor as shown.
43042-01 02/21/2008 19 Align glass dome and push up. Screw glass stop into position. Screw Finial into position Complete. Attach thumbscrews. W ARNING: T o reduce the risk of electrical shock, all 4 thumbscrews MUST be properly installed. Install 2 Max 60 W att A15 bulbs (Not Included).
43042-01 02/21/2008 20 T rouble Shooting Problem: Fan does not come on. Solution: • Hunter Fan Bath V entilators are extremely quiet. T o conrm that the fan is running, place your hand near the vents to feel the air movement. • T urn power on, replace fuse, or reset breaker .
43042-01 02/21/2008 21 W arranty © 2008 Hunter Fan Company Hunter Fan Company Bath Exhaust Fan LIMITED W ARRANTY Hunter Fan Company makes the following limited warranty to the original user or consum.
An important point after buying a device Hunter Fan 82048 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hunter Fan 82048 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hunter Fan 82048 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hunter Fan 82048 you will learn all the available features of the product, as well as information on its operation. The information that you get Hunter Fan 82048 will certainly help you make a decision on the purchase.
If you already are a holder of Hunter Fan 82048, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hunter Fan 82048.
However, one of the most important roles played by the user manual is to help in solving problems with Hunter Fan 82048. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hunter Fan 82048 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
