Instruction/ maintenance manual of the product 43045 Hunter Fan
Go to page of 18
43045-01 10/15/2009 1 Installation Guide Energy Star Bath Fan Models 82043 READ and SA VE THESE INSTRUCTIONS ENGLISH See page 2 ESp añoL V ea la página 19.
43045-01 10/15/2009 2 1) Read all instructions before attempting to install or use this appliance. This appliance is for general ventilating use only .
43045-01 10/15/2009 3 6) Never place a switch where it can be reached from a tub or shower . Do not install this appliance in a tub or shower enclosure. 7) Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction codes and standards.
43045-01 10/15/2009 4 F G I L M x2 N x6 * * A B C 98141-01-000 03242-07-133 98142-01-000 x2 D 97134-01-000 74508-03-133 Housing Wiring Co ver F an Assembly 3/8” Cable Connector Light F ixture Wiring Co ver Screw Check all the parts. If damag ed , call 1-888-830-1326 for replacement.
43045-01 10/15/2009 5 Loosen the wiring cover screw . Remove the fan assembly from the housing. Remove the wiring cover . D E C Choose Installation Option For New Construction - attaching to joist, go to step A1, page 5. For New Construction - suspended between, joists go to step B1, page 7.
43045-01 10/15/2009 6 A 1 Section A - New Construction - attaching to joist Drive mounting screws (supplied) into joist or framing. Position the correct depth mark at the bottom edge of the joist based upon the the thickness of your sheetrock. 5/8 1/2 5/8 1/2 A 2 Pop out a wiring access slug.
43045-01 10/15/2009 7 A 6 Connect 6” duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely , an adapter may need to be purchased. Vaya a la sección E – Instalación Final en la página 14. Section B - New Construction – suspended between joists Pop out a wiring access slug.
43045-01 10/15/2009 8 Mark position of screws by using holes as a template. Drill a pilot hole at the TOP of each outline. B4 1/16” bit B5 Insert mounting screws, leaving space between the screw head and the joist. (Screws are supplied.) Attach the rails onto the screws.
43045-01 10/15/2009 9 B10 Install the wiring and the strain relief into the wiring access hole you made earlier . B11 Connect 6” duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely , an adapter may need to be purchased.
43045-01 10/15/2009 10 Slide the mounting rails into brackets. C3 5/8 1/2 5/8 1/2 C4 Using the depth markings on the housing, position the bottom edge of the housing so that it will be flush with the sheetrock. Pop out a wiring access slug. C6 C5 Mark position of screws by using holes as a template.
43045-01 10/15/2009 1 1 C7 Insert mounting screws, leaving space between the screw head and the joist. (Screws are supplied.) Attach the rails onto the screws. C8 C9 Tighten screws. 3” C 1 0 Run the power supply wire through the strain relief, leaving 3” between the end of the wire and the strain relief.
43045-01 10/15/2009 12 Vaya a la sección E – Instalación Final en la página 14. Section D - Existing Construction – accessible from below Remove one of the wiring access slugs on the top of the housing. Use a second wiring access plug if needed.
43045-01 10/15/2009 13 Connect 6” duct and vent to the outside. Use duct tape to secure joints. If ducting does not fit securely , an adapter may need to be purchased. Install the wiring and the strain relief into the wiring access hole you made earlier .
43045-01 10/15/2009 14 E2 E 3 Connect fan wiring harness. DO NOT ALLOW THE F AN TO HANG FROM THE WIRING HARNESS. INST ALLA TION IS EASIER IF TWO PEOPLE ARE INVOL VED. Install the wiring cover box. Make sure all wiring connec- tions are inside the wiring cover box.
43045-01 10/15/2009 15 E5 Secure the fan assembly by tightening the two fan mounting screws. E7 Install the strain relief bracket. DO NOT ALLOW THE LIGHT FIXTURE TO HANG FROM THE WIRING HARNESS. INST ALLA TION IS EASIER IF TWO PEOPLE ARE INVOL VED. E8 E6 E6 E7 Remove thumbnuts.
43045-01 10/15/2009 16 E15 Complete. E9 E13 Install light bulb cover . Restore power at the source. E11 E12 Secure the fan assembly by tightening the two fan mounting thumbnuts.
43045-01 10/15/2009 17 T rouble Shooting Problem: Fan does not come on. Solution: • T urn power on, replace fuse, or reset breaker. • Hunter Fan Bath V entilators are extremely quiet. T o conrm that the fan is running, place your hand near the vents to feel the air movement.
43045-01 10/15/2009 18 Hunter Fan Company Bath Fan LIMITED W ARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter Bath Fan: If any .
An important point after buying a device Hunter Fan 43045 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hunter Fan 43045 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hunter Fan 43045 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hunter Fan 43045 you will learn all the available features of the product, as well as information on its operation. The information that you get Hunter Fan 43045 will certainly help you make a decision on the purchase.
If you already are a holder of Hunter Fan 43045, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hunter Fan 43045.
However, one of the most important roles played by the user manual is to help in solving problems with Hunter Fan 43045. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hunter Fan 43045 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
