Instruction/ maintenance manual of the product MQX-2150 Huffy
Go to page of 18
1 05/03 P/N 211994B © COPYRIGHT 2000 by HUFFY SPORTS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-333 061 Internet Address: http://www.
2 P/N 211994B 05/03 W ARNING F AILURE TO FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or any part of the system including bac kboard, suppor t braces or net.
05/03 P/N 211994B 3 SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system.
4 P/N 211994B 05/03 For more information on assembly, placement, proper use and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are packed inside.
05/03 P/N 211994B 5 Get to know the basic parts of your basketball system..... STRUTS BACKBOARD FRONT RIM WHEEL CARRIAGE ASSEMBL Y BASE POLE.
6 P/N 211994B 05/03 P ARTS LIST - (See Hardware Identifier) Item Qty . Part No. Description 1 1 206645 T ank (Black) 2 1 200628 Wheel Axle 3 2 226401 Wheel 4 1 900060 T op Pole Section 5 1 908480 Middle Pole Section with Label 6 1 908490 Bottom Pole Section 7 1 202820 Rod, 3/8 O.
05/03 P/N 211994B 7 HARDW ARE IDENTIFIER Item #14 (1) Item #12 (6) Item #10 (1) Item #19 (12) Item #16 (2) Item #17 (6) Item #21 (4) Item #28 (2) Item #22 (4) Item #23 (2) Item #8 (1) Item #1 1 (1) It.
8 P/N 211994B 05/03 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION A : ASSEMBLE THE BASE 9/16” and 1/2” 9/16” and 1/2” AND/OR This is what your system.
05/03 P/N 211994B 9 1. 1 Remove contents from t ank 5” (13 cm) 2. Correctly identify each pole section and mark indicated distance from ends with t ape (not supplied) as shown. 3. IMPORT ANT! Center the alignment slot of middle pole section (5) in the lower hole of top pole section (4) as shown.
10 P/N 211994B 05/03 4 5 6 WOOD SCRAP 4. IMPORT ANT! Center the alignment slot of lower pole section (6) in the lower hole of middle pole section (4) as shown. While maintaining alignment, bounce top and middle pole assembly (4 & 5) onto bottom section of pole (6) using wood scrap as shown until they no longer move toward taped reference mark.
05/03 P/N 211994B 11 10 6 7 8 6. 2 28 28 3 3 9 Install wheel axle (2) through wheel carriage (9). Inst all wheels (3) onto wheel axle (2) with spacers (28) as shown. Insert pole assembly into t ank assembly as shown. Secure bottom pole (6) to tank and wheel bracket as shown.
12 P/N 211994B 05/03 8. 13 13 1 Secure non-secured ends of tank strut s (13) to t ank as shown. Repeat for opposite side. 13 17 12 12 16.
05/03 P/N 211994B 13 TOOLS REQUIRED FOR THIS SECTION HARDW ARE USED IN THIS SECTION (not actual size) SECTION B: ASSEMBLE THE BOARD AND RIM 1/2” 1/2” AND/OR This is what your system will look like.
14 P/N 211994B 05/03 21 22 22 18 20 17 17 Mount brackets (20) and rim (18) to backboard and finger tighten as shown. NOTE: Final adjustment s will be made in S tep 3 of this section IMPORT ANT! For spring loaded rim assembly , refer to instructions included with rim hardware.
05/03 P/N 211994B 15 2. SAWHORSE OR SUPPORT TABLE 5 24 23 3. While still in the horizont al position, carefully slide backboard components onto pole. Secure hardware at desired position as shown and tighten all hardware completely at this time. Support pole and tank assembly over support t able.
16 P/N 211994B 05/03 4. Install clip s. CLI P “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows.
05/03 P/N 211994B 17 Insert net into bottom of clip as shown. SIDE VIEW T wist net until it snap s into position. Net must be centered through clip. NET NETCLIP SIDE VIEW NET NETCLIP NET INST ALLA TION 9.
18 P/N 211994B 05/03 15 1. 10 feet (3.05 m) Carefully upright assembly . Apply moving system label (15) to front of pole as shown. Regulation rim height is 10 feet (3.05 m). TWO PEOPLE REQUIRED FOR THIS PROCEDURE. F AILURE TO FOLLOW THIS W ARNING COULD RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE.
An important point after buying a device Huffy MQX-2150 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Huffy MQX-2150 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Huffy MQX-2150 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Huffy MQX-2150 you will learn all the available features of the product, as well as information on its operation. The information that you get Huffy MQX-2150 will certainly help you make a decision on the purchase.
If you already are a holder of Huffy MQX-2150, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Huffy MQX-2150.
However, one of the most important roles played by the user manual is to help in solving problems with Huffy MQX-2150. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Huffy MQX-2150 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
