Instruction/ maintenance manual of the product DCM230 Huffy
Go to page of 18
12/02 P/N 211446D 1 T oll-Free Customer Service Number for U.S: 1-800-558-5234 Internet Address: http://www .hydra-rib.com IMPORT ANT! Have any questions?...Don’t go back to the store! We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection.
2 P/N 211446D 12/02 IMPORT ANT! WRITE MODEL NUMBER FROM BOX ONT O P AGE 1 OF THIS OWNERS MANUAL W ARNING F AILURE T O FOLLO W THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPER TY D AMA GE. Owner must ensure that all pla yers kno w and follow these rules for saf e operation of the system.
24" (61 cm) 36" (91.4 cm) Ensure ground is level with playing surface, then dig pole hole. GROUND SURFACE PLAYING SURFACE 1. Install threaded ends of J-bolts (1) through holes in mounting plate (3) and secure as shown. NOTE: Make sure J-bolts (1) are in the illustrated position.
4 P/N 211446D 12/02 Fill hole with concrete. Tamp down concrete to release air pockets and build drainage hill. Insert J-bolts (1) from mounting plate (3) into cement as shown. Move assembly around to release any air pockets in cement, then rest mounting plate on cement drainage hill.
5 12/02 P/N 211446D Upright pole (5). Assemble lower pole flange onto protruding J-bolts (1) as shown. The flange will then rest on the nuts (2) from Step 2. Secure pole (5) flange to mounting plate (3) as shown. Tighten completely. 6. 7. 5 THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE.
6 P/N 211446D 12/02 8. Insert caps (8) into end of each support arm (9 & 10) as shown. Tap firmly in position. Apply logo label (11) to lower support arms (10) as shown. Repeat for opposite side. Beginning with upper support arms (9) secure support arms to pole.
7 12/02 P/N 211446D 1 1. 16 14 3 9 14 7 13 14 10 7 14 10 7 14 16 14 7 14 9 16 14 16 THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPOR T ANT! Do not over tighten.
Position U-joint of crank jack (20) as shown. Where tubes on crank jack join, hold steady to keep both tubes from rotating. Rotate handle clockwise on crank jack to the fully extended position. Upright crank jack. 8 P/N 211446D 12/02 12. Secure jack brackets (17 & 18) to lower holes in pole as shown.
9 12/02 P/N 211446D 14. Install crank jack (20) U-joint to lower set of support arms (10) as shown. 10 14 20 7 14 21 12 10 THREE PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE.
10 P/N 211446D 12/02 15. Rotate jack handle clockwise to raise H-frame (13) to approximately 7’ (2.1 m) from ground. Secure crank jack (20) to jack brackets (17 &18) as shown. NOTE: Some adjustment will be necessary to align the lower crank jack bushing to jack brackets (17 & 18).
11 12/02 P/N 211446D RIM ASSEMBL Y & INST ALLA TION WARNING 17. Install carriage bolt (41) through rim (25), washers (4) and (27) as shown. Tighten nut (43) completely. Place nut (42) about half-way up carriage bolt (41) as shown. 25 4 41 27 43 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE.
12 P/N 211446D 12/02 20. 25 39 40 Insert spacer (45) through rim assembly (25). Place rim assembly on bracket (39) so that carriage bolt (41) is inserted through hole on top of inner bracket (40). Install hex bolt (44), washers (27) and nut (42) through top holes on bracket (39) through spacer (45) as shown.
13 12/02 P/N 211446D 22. 23. 24. Apply logo label (33) to cover plate (31). Install cover plate (18) on rim (25) using self tapping screws (32) as shown. LEVELING INSTRUCTIONS: Place level on rim (25) and adjust nut (42) until level. Tighten nut (30) to set rim tension for playing.
14 P/N 211446D 12/02 Apply height adjustment label (37) to front of pole as shown. 26. 10 feet (3.05 m) REGULATION RIM HEIGHT IS 10 FEET (3.05 m). 37 25. Check leveling at this time. Pole should be level in all directions. NOTE: If adjustment is necessary, adjust system by rotating the nuts (2) between mounting plate (3) and pole flange.
15 12/02 P/N 211446D 27. A. LOWER BACKBOARD UNTIL RIM IS 7 FEET OFF THE GROUND. B. APPLY THIN WHITE STRIP TO BOTTOM EDGE OF OUTER CRANK TUBE AS SHOWN. C. APPLY LARGE DECAL TO BACK OF POLE SO THAT 7 FOOT MARK ON LARGE DECAL IS LINED UP WITH THIN WHITE STRIP.
16 P/N 211446D 12/02 Rotate crank handle to raise and lower backboard. NOTE: If height adjustment is difficult to operate, you may have over tightened the areas indicated. Refer to Step 10 and Step 14. 29. Secure pole pad (36) as shown. 28. 36 Height Adjustment NOTE: Pole pad may NOT be included in this model.
17 12/02 P/N 211446D Item Qty. Part No. Description 1 4 200573 J-Bolt, 5/8”-11” 2 12 265575 Nut, Hex 5/8”-11” 3 1 920880 Mounting Plate 4 8* 203470 Washer, Flat 5/8” I.
18 P/N 211446D 12/02 Item #41 (1) Item #24 (8) Item #30 (1) Item #32 (2) Item #28 (1) Item #23 (4) Item #42 (2) HARDW ARE I DENTIFIER Item #44 (1) Item #45 (1) Item #43 (1) WARRANTY CARD: Please remember to complete your product registration form on-line at: www.
An important point after buying a device Huffy DCM230 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Huffy DCM230 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Huffy DCM230 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Huffy DCM230 you will learn all the available features of the product, as well as information on its operation. The information that you get Huffy DCM230 will certainly help you make a decision on the purchase.
If you already are a holder of Huffy DCM230, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Huffy DCM230.
However, one of the most important roles played by the user manual is to help in solving problems with Huffy DCM230. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Huffy DCM230 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
