Instruction/ maintenance manual of the product AR325W Huffy
Go to page of 33
1 01/04 P/N 214955E © COPYRIGHT 2000 by HUFFY SPORTS Toll-Free Customer Service Number for U.S: 1-800-558-5234, For Canada: 1-800-284-8339 , For Europe: 00 800 555 85234 (Sweden: 009 555 85234 ), For Australia: 1-800-333 061 Internet Address: http://www.
2 P/N 214955E 01/04 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est-fit large bolt s into large holes of elevator tubes, backboard bracket s, and triangle plates.
01/04 P/N 214955E 3 W ARNING F AILURE T O FOLLOW THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NO T HANG on the rim or any part of the system including bac kboard, support braces or net.
4 P/N 214955E 01/04 For more information on assembly, placement, proper use, and maintenance, visit The American Basketball Council website at http://www.smarthoops.com. IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are packed inside.
01/04 P/N 214955E 5 2 2 1 3 TO ADJUST BACKBOARD: 1. While holding handle, remove pin. 2. Move elevator up or down to desired height. 3. Replace pin full length to lock system at desired height. 201252 2/99 1 2 4 3 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position.
6 P/N 214955E 01/04 Get to know the basic parts of your basketball system..... SUPPOR T STRUT BACKBOARD FRONT RIM BASE POLE FRONT P ANEL WHEELS.
01/04 P/N 214955E 7 P ARTS LIST - See Hardware Identifier Item Qty . Part No. Description 1 1 206336 Tank 2 2 206330 Wheel Axle, 4-1/4 Long 3 2 226401 Wheel, 4“ (Black) 4 1 904847 Top Pole Section 5 1 908024 Middle Pole Section 6 1 908487 Bottom Pole Section 7 1 202820 Rod, 3/8 O.
8 P/N 214955E 01/04 * You may have extra parts with this model. Item #8 (1) Item #15 (2) Item #18 (2) Item #25 (1) Item #30 (2) Item #31 (1) HARDW ARE IDENTIFIER (BOL TS & SCREWS) Item #47 (6) Ite.
01/04 P/N 214955E 9 Item #23 (2) Item #22 (2) Item #36 (2) Item #44 (2) Item #57 (4) Item #38 (4) Item #50 (12) Item #2 (2) Item #7 (1) HARDW ARE IDENTIFIER (STEEL SP ACERS & RODS) HARDW ARE IDENT.
10 P/N 214955E 01/04 Insert axle rod (2) through wheel (3), as shown. Secure wheel assembly to tank (1) by t apping wheel downward with hammer , snapping it into position. Repeat for opposite side, then carefully , turn t ank (1) over . Remove all contents from underside of tank.
01/04 P/N 214955E 11 IMPORT ANT! Center alignment slot of lower pole section (6) in a lower hole of middle pole section (5) as in step 3. While maintaining alignment, bounce top & middle pole assembly (4 & 5) onto lower pole section (6) as shown until top & middle pole assembly no longer moves toward taped reference mark on bottom pole.
12 P/N 214955E 01/04 Insert pole assembly into tank assembly as shown. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). DO NOT OVER TIGHTEN IMPORT ANT!: DO NOT OVER TIGHTEN IMPORT ANT!: TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
01/04 P/N 214955E 13 1 11 15 16 11 1 13 13 11 12 13 6 14 13 4 16 37 18 18 16 17 Secure strut tubes (1 1) to bottom pole section (6) as shown. Carefully place unit in the side position and secure strut (1 1) to t ank (1) as shown. Completely tighten. Repeat for opposite side.
14 P/N 214955E 01/04 19 21 21 19 19 20 20 19 17 22 22 23 23 Attach sp acers (22, 23) to pole mount bracket (17) with bolt s (21), washers (19), and nuts (20) as shown. Tighten just until washers (19) stop moving. IMPORT ANT!: 17 16 26 24 24 27 25 FIG .
01/04 P/N 214955E 15 30 29 16 28 28 Apply logo and height indicator labels (29) to adjustment rod (28) as shown. Attach handle part s (32, 33) to adjustment rod with screw (31), carriage bolt (30), and flange nut (16) as shown. Insert handle assembly through pole mount assembly as shown.
16 P/N 214955E 01/04 36 36 21 21 20 20 34 Attach backboard support bracket s (34) to the backboard frame using bolt s (21), spacers (36), and nut s (20) as shown.
01/04 P/N 214955E 17 47 42 40 41 40 55 57 57 34 39 Attach rim to board as shown. For spring loaded rim assembly , refer to instructions included with rim hardware. Assemble lower elevator tubes (40) as shown. DO NOT overtighten. IMPORT ANT!: Refer to instructions included with board and rim hardware for backboard and rim assembly .
18 P/N 214955E 01/04 43 41 43 47 57 34 39 57 Assemble upper elevator tubes (43) to backboard brackets (34). DO NOT overtighten. SAWHORSE OR SUPPORT TABLE Support pole on sawhorse. Attach backboard assembly to top pole section (4) as shown. Install pole cap (46).
01/04 P/N 214955E 19 47 39 44 44 28 Install upper elevator tubes (43) to triangle plates (45) as shown. Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. NOTE: IMPORT ANT!: DO NOT OVER TIGHTEN 40 47 38 40 39 43 38 45 43 20.
20 P/N 214955E 01/04 41 39 47 43 43 53 49 52 Insert bolt (47) through left side upper elevator tube (43), then stretch spring (41) onto bolt (47). Insert bolt (47) through right side upper elevator tube (43) and secure with nut (39) . Roll completed assembly to desired position.
01/04 P/N 214955E 21 26 10. 11 . 12. 54 10 f t. (3.05 m) While holding handle, remove pin (26). Move elevator up or down to desired height. Replace pin (26) full length to lock system at desired height. Apply height and transport label (54) to front of pole as shown.
22 P/N 214955E 01/04 35 11 11 56 56 35 Install front cover (35) onto strut s (1 1) as shown. Loop zip tie (56) around strut (1 1) and cover (35). Pull flat end of zip tie (56) through square end of zip tie until completely tightened. Once fully secured in the four areas shown, trim excess of zip tie (56) with scissors.
01/04 P/N 214955E 23 CLIP “ARM” CLIP “BODY” A A B B C C 50 Install net clips. Installez les pinces du filet. Netzhalteklammern anbringen. Instale los sujetadores de la red.
24 P/N 214955E 01/04 NET INST ALLA TION Install net. Installez le filet. Das Netz anbringen Instale la red. Insert net into bottom of clip as shown. Insérez le filet dans la base de la pince, comme illustré. Das Netz wie gezeigt unten in den Clip stecken.
25 01/04 P/N 214955E Numéro d’appel gratuit du service après-vente. Etats-Unis et Canada uniquement: 1-800-284-8339 Numéro vert international (France, Suisse) : 00 800 555 85234 TUFF STUFF® et les marques associées de Mattel, Inc. sont utilisées avec sa permission.
INSTRUCTIONS IMPORTANT ! NOTEZ À LA PAGE 1 DE CE MANUEL LE NUMÉRO DE MODÈLE MENTIONNÉ SUR LE CARTON. AVANT DE COMMENCER ! Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien ajustés (serrés).
01/04 P/N 214955E 27 Légende Quantité No de réf. Description 1 1 206336 Réservoir 2 2 206330 Axe des roues, longueur 4-1/4 3 2 226401 Roue, 10 cm (noire) 4 1 904847 Section de poteau supérieure 5 1 908481 Section de poteau centrale 6 1 908487 Section de poteau inférieure 7 1 202820 Tige, D.
28 P/N 214955E 01/04 00 800 555 85234 INSTRUCCIONES DE SEGURIDAD La mayoría de las lesiones son ocasionadas por el mal uso y/o por no seguir las instrucciones. Tenga cuidado cuando use esta unidad. • Tenga mucho cuidado si utiliza una escalera durante el montaje.
INSTRUCCIONES ¡IMPORTANTE! ANOTE EN LA PÁGINA 1 DE ESTE MANUAL DEL PROPIETARIO EL NÚMERO DE MODELO QUE APARECE EN LA CAJA. ¡ANTES DE COMENZAR! Para asegurar el óptimo rendimiento del sistema del respaldo en el juego, se requiere un ajuste de tolerancia estrecha entre los componentes del elevador y el herraje.
30 P/N 214955E 01/04 Artículo Cant. Pieza N.º Descripción 1 1 206336 Tanque 2 2 206330 Eje de la rueda, 4-1/4 de longitud 3 2 226401 Rueda, 4" (10,2 cm) ( (negra) 4 1 904847 Sección superior del poste 5 1 908481 Sección media del poste 6 1 908487 Sección inferior del poste 7 1 202820 Varilla, 3/8 D.
31 01/04 P/N 214955E Universelle gebührenfreie Telefonnummer (Deutschland, Schweiz): 00 800 555 85234 TUFF STUFF® und die damit verbundenen Warenzeichen sind Eigentum von Mattel, Inc.
GEBRAUCHSANLEITUNG WICHTIG! NOTIEREN SIE SICH DIE MODELLNUMMER AUS DEM KÄSTCHEN AUF SEITE 1 DIESES BENUTZERHANDBUCHS VORBEREITENDE MASSNAHMEN Um sicherzustellen, dass das Korbwandsystem optimal für .
01/04 P/N 214955E 33 Artikel Menge Teilenummer Beschreibung 1 1 206336 Tank 2 2 206330 Radachse, 4-1/4 Länge 3 2 226401 Rad, 4 Zoll (schwarz) 4 1 904847 Oberes Stangenteil 5 1 908481 Mittleres Stange.
An important point after buying a device Huffy AR325W (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Huffy AR325W yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Huffy AR325W - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Huffy AR325W you will learn all the available features of the product, as well as information on its operation. The information that you get Huffy AR325W will certainly help you make a decision on the purchase.
If you already are a holder of Huffy AR325W, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Huffy AR325W.
However, one of the most important roles played by the user manual is to help in solving problems with Huffy AR325W. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Huffy AR325W along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
