Instruction/ maintenance manual of the product 89225 Huffy
Go to page of 20
1 P/N 21154401 01/04 IMPORT ANT! T o ensure prompt and correct handling of any problems, or to answer any questions, please contact the Sample and Display T echnician at 1-800-558-5234.
P/N 21154401 01/04 2 BEFORE YOU ST ART! T o ensure optimal playability of backboard system, a close tolerance fit between the elevator component s and hardware is required. T est fit large bolts into large holes of elevator tubes, backboard bracket s and triangle plates.
3 P/N 21154401 01/04 IMPORT ANT! Remove all content s from boxes. Be sure to check inside pole sections; hardware and additional p art s are packed inside. NOTICE T O ASSEMBLERS AL L Huffy Sport s Basketball Systems, including those used for DISPLA YS, MUST be assembled and ballasted with sand or water according to the instructions.
P/N 21154401 01/04 4 P A R TS LIST (See Hardware Identifier) Item Qty. Part No. Description 1 2 900033 Back Bracket 2 2 203796 T-Bolt, 3/8-16 x 5 3 2 200318 Bracket 4 2 203472 Spring 5 2 201651 Spacer, .50 I.D. x .25 Long 6 2 206303 Washer, 1/4" Flat 7 8* 203113 Bolt, Hex-Flange 5/16-18 x 2.
5 P/N 21154401 01/04 Item #33 (12) Item #30 (4) Item #40 (4) HARDW ARE IDENTIFIER (BOL TS & SCREWS) Item #67 (2) PLASTIC SP ACERS Item #7 (10) Item #4 (2) Item #22 (2) Item #13 (2) Item #27 (5) It.
P/N 21154401 01/04 6 Install display boards in the marked locations. Each mounting location consist s of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing).
7 P/N 21154401 01/04 At corner locations 1, 2, and 3 install the display pole to the mounting pole stub. If required, secure the display pole by sliding the display wedge (12) into position as shown. T o lock the display pole in place, tighten the set screw (13 or 39).
P/N 21154401 01/04 8 8 11 49 16 1. 2. 17 30 24 52 51 49 30 3. 49 8 55 54 54 57 44 57 55 4. 48 8 46 45 26 47 25 Install pole mount bracket (49) with carriage bolts (16) as shown. T ighten flange nuts (8) completely . Attach sp acers (51, 52) to pole mount bracket (49) with bolts (24), washers (30), and nuts (17) as shown.
9 P/N 21154401 01/04 STEEL FRAME A CR YLIC BACKBOARD ASSEMBL Y - Corner Location 1 37 5. 38 38 24 24 17 17 Attach backboard support brackets (37) to the backboard frame using bolts (24), spacers (38), and nuts (17) as shown . 29 29 39 39 59 37 42 Refer T o Instructions Included With Rim Hardware For Rim Assembly .
P/N 21154401 01/04 10 7. 21 21 27 59 37 42 59 Attach upper elevator tubes (21) to backboard support bracket s (37) using spacers (59), bolt (27), and nut (42) as shown. 8. Attach backboard assembly to pole section (1 1). Install pole cap (43). 42 21 43 21 29 29 27 27 USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY.
11 P/N 21154401 01/04 10. 9. Insert handle assembly through pole mount assembly as shown. Lock pole assembly in place at the 10’ (3.05m) mark with pin (55). Attach adjustment rod (47) to lower elevator tubes (29) using bolt (27) spacer (59) and nut (42) as shown.
P/N 21154401 01/04 12 3 35 22 4 58 1 2 • Fit rim (58) securely into bracket (1) as shown. • Install reinforcement bracket (3) onto “T” bolt (2) as shown. • Install spring (4) onto “T” bolt (2) as shown. • Install special nut (35) and washer (22) onto “T” bolt (2).
13 P/N 21154401 01/04 44” F AN MOLDED PLASTIC BOARD ASSEMBL Y - Corner Location 2 Correctly identify each pole section. ONL Y THE T OP POLE SECTION (14) IS USED IN THIS ASSEMBL Y . 1. BOTTOM POLE 43” MIDDLE POLE 43” TOP POLE 31” 14 Fit spacer (15) into p awl (19).
P/N 21154401 01/04 14 Assemble elevator tubes (21) to ratchet (28) and backboard brackets (23) using bolt s (20), spacers (5, & 40), and nut s (42) as shown. T ighten completely . 5 . Secure pawl (19) in place with clevis pin (31) and washers (6) as shown.
15 P/N 21154401 01/04 7. Insert “T” bolt (2) through Slam Jam bracket (1) as shown. Secure Slam Jam bracket (1) and backboard bracket (23) assemblies to backboard. Bend upper halves of backboard brackets (23) to line up with holes in backboard and secure with bolts (44 & 7) and nut s (8).
P/N 21154401 01/04 16 20 20 41 9. Attach upper and lower elevator tubes (21) to top pole section (14) using bolt s (20) and nuts (42) as shown. Attach pole cap (41) as shown. 42 21 21 21 21 • Fit rim (58) securely into bracket (1) as shown. • Install reinforcement bracket (3) onto “T” bolt (2) as shown.
17 P/N 21154401 01/04 Correctly identify each pole section. Poles have an identification sticker that will be used as a reference point in the next step. ONL Y THE T OP POLE SECTION (50) IS USED IN THIS ASSEMBL Y . F AN MOLDED PLASTIC BOARD ASSEMBL Y - Corner Location 3.
P/N 21154401 01/04 18 F AN BACKBOARD ASSEMBL Y - Corner Location 4. TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. WARNING Assemble fan backboard as shown below with a standard rim as shown. 33 32 33 8 65 7 33 1.
19 P/N 21154401 01/04 Install net clip s. CLIP “ARM” CLIP “BODY” Insert one “arm” of clip into ram as shown. T wist “body” of clip slightly so that second “arm” slides over the top of the first “arm” as shown. Push in direction indicated by arrows.
P/N 21154401 01/04 20 Install net. Insert net into bottom of clip as shown. SIDE VIEW T wist net until it snaps into position. Net must be centered through clip.
An important point after buying a device Huffy 89225 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Huffy 89225 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Huffy 89225 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Huffy 89225 you will learn all the available features of the product, as well as information on its operation. The information that you get Huffy 89225 will certainly help you make a decision on the purchase.
If you already are a holder of Huffy 89225, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Huffy 89225.
However, one of the most important roles played by the user manual is to help in solving problems with Huffy 89225. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Huffy 89225 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
