Instruction/ maintenance manual of the product 5000 Series Hudson Sales & Engineering
Go to page of 8
Installation Manual 5000 Page 1 of 8 August 2000 T uf-Lite and T uf-Lite II Fans 5000 Series Hub INST ALLA TION MANUAL Adjustable Pitch Fan Assembly 22’ through 30’ Diameter Hudson T uf-Li.
Installation Manual 5000 Page 2 of 8 August 2000 ASSEMBL Y WITH BUSHING Clean all mating surfaces between hub, bushing and shaft. All grease and lubricant should be removed, leaving the mating sur - faces dry .
Installation Manual 5000 Page 3 of 8 August 2000 THRUST RET AINER (optional equipment) Install proper load bolt (not provided) into top of fan shaft and tighten (See Figure 1). Install thrust retainer channel on top hub plate using existing hub spool cap screws.
Installation Manual 5000 Page 4 of 8 August 2000 Rotate blade in clamp until digital protractor shows specified pitch angle to within ± 0.2˚. Fan pitch angle is shown on fan specification sheet for design duty . After desired pitch angle is set, raise and lower end of fan blade and find midpoint of blade travel.
Installation Manual 5000 Page 5 of 8 August 2000 After mounting, install flat washer, lock washer , and 3/8” NC nuts. Tighten to 15 ft-lb (lubricated) or 20 ft-lb (dry). (See Figure 7) Note: Refer to instructions included with seal disc for further details.
Installation Manual 5000 Page 6 of 8 August 2000 HUDSON PRODUCTS CORPORA TION Adjustable Pitch Fan Assembly 22’ Thru 30’ Diameter Series 5000 HUB ST ANDARD MA TERIALS & FINISHES Blades: Fiberg.
Installation Manual 5000 Page 7 of 8 August 2000 HU B MODEL N O. & SERIAL N O. 1 5 68 7 10 9 F U R N IS HED WI TH BUS HIN G KEY , SET SC REW & CAP SCR EWS 3 2 BALANC E. (BL U E BLADES O NL Y) AND F I NAL M OM ENT D ATE O F M ANU FAC T UR E SERIAL N O.
Installation Manual 5000 Page 8 of 8 August 2000 1307 Soldiers Field Drive Sugar Land, T exas 77479-4072 Post Of fice Box 20029 Sugar Land, T exas 7777496-0029 Phone: (281) 275-8100 Fax: (281) 275-8388 1-800-634-9160 (24 Hours) EMAIL: hudson.products@hudsonproducts.
An important point after buying a device Hudson Sales & Engineering 5000 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hudson Sales & Engineering 5000 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hudson Sales & Engineering 5000 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hudson Sales & Engineering 5000 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Hudson Sales & Engineering 5000 Series will certainly help you make a decision on the purchase.
If you already are a holder of Hudson Sales & Engineering 5000 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hudson Sales & Engineering 5000 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Hudson Sales & Engineering 5000 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hudson Sales & Engineering 5000 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
