Instruction/ maintenance manual of the product LASERJET P2055 HP
Go to page of 14
HP ® LASERJET P2035 • 2055 CAR TRIDGE REMANUF ACTURING INSTRUCTIONS TONER CARTRIDGE HP ® LASERJET P035 • 2055 PRINTER 3232 West El Segundo Blvd., Ha wthorne, California 90250 USA • Ph +1 42 4 675 3300 • Fx +1 424 675 3400 • t echsuppor t@uninetimaging.
REMANUF ACTURING THE HP LASERJET P2035 • 2055 TONER CAR TRIDGE By Mike Josiah Figures abov e show the dif f erent physical sizes of the two cartridges. The car tridges are similar in design to the 1 160/1 320 car- tridges, but are not inter changeable.
SUPPLIES REQUIRED 11 0g HP-P2035 toner f or the CE505A car tridge (2,300 pages) 290g HP-P2035 toner f or the CE505X car tridge (6,500 pages) Replacement Chip New Drum (Optional) Uninet #1 33 72 - HP P 2035, 2055 Unidrum ™ gearless recommended. Wiper Blade (Optional) Dr .
2. Drill a shallow hole on each side of the cartridge as indicated by the arr ows. Figures shown bef ore drilling. Af t er drilling. HP P2035 • 2055 CARTRIDGE REMANUF ACTURING INSTRUCTIONS 3232 West El Segundo Blvd., Ha wthorne, California 90250 USA • Ph +1 42 4 675 3300 • Fx +1 424 675 3400 • t echsuppor t@uninetimaging.
3. Push the pins out with a jew eler’s screwdriver . With the hole in this location by just pushing the scre wdriver in, the pins will be pushed out. Remo ve the pins. 4. Separate the tw o halves. 5. With a flat head screwdriv er , press the drum axle pin out from the inside of the cartridge wall as shown.
The drum hub on the opposite side is w elded. The weld can be brok en or drilled out, but there is a good chance that the hub will either warp if pried off, or will be hard to align if drilled out. 6. Remo ve the drum. This is a good time to look at the ne w drive gear(s).
1 0. Coat the wiper blade with your preferred lubricant. Install the blade and 2 screws. 11 . Re-install the cleaned PCR. Note that a ne w OEM PCR has a small amount of conductive grease on the black (contact) side. 12. Re-Install the OPC Drum and metal axle pin.
13. Slice the two tabs off each location as shown on the left (Seal) end cap. Use a square blade X-Acto knif e to slice off the tabs. NOTE : Both the end caps are plastic welded in place. The only wa y to open them up is to cut the w elds and carefully drill them out.
1 7 . Remo ve the Magnetic roller driv e gear . The end cap will keep the bushing in place. 18. Remo ve the DR. Blade and two scre ws. 19. Clean out an y remaining toner from the hopper . Note the Dr . Blade seal. It is a sticky substance that can be clean with alcohol if toner gets on it.
2 1. If you are going to seal the cartridge, there is a white plas- tic shelf that needs to be remo ved. The shelf is held on with double sided tape. It can be gently pried of f with a small scre w- driver . 22. Re-install the whit e plastic shelf. If the adhesive is not working, replace it with a good double sided tape.
26. Install 2 small screws int o the holes previously drilled out. Leav e the top 3rd hole alone! (This w eld was brok en when the end cap was remo ved). A screw here will int er fere with installing the car tridge in the printer . In our tests, the two screws will hold the end cap on with no pr oblems.
2 7 . Place the tw o halves together , make sure that the two springs are aligned, and insert the two pins. Make sure that the pins are slightly pushed in so that they do not int er f ere with installing the car tridge in the printer . 28. Install the drum cov er; make sure the spring is situat ed correctly.
TROUBLESHOOTING Repetitiv e Defect Char t OPC Drum: 75mm Low er Fuser r oller 63mm Upper F user film 5 7mm Registration r oller 43mm Magnetic Roller 42mm T ransfer roller 39mm PCR 38mm RUNNING TEST P A GES P2030 Series Only T o run the Demo Page, mak e sure that the ready light is on, and briefly press the GO button.
RUNNING THE CLEANING P A GE P2030 Only T o run the Cleaning Page, mak e sure that the ready light is on. Inser t a transparency in the paper tray . Open the printer -driver pr oper ties screen and click on the device settings tab. In the cleaning page area press star t.
An important point after buying a device HP LASERJET P2055 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought HP LASERJET P2055 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data HP LASERJET P2055 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, HP LASERJET P2055 you will learn all the available features of the product, as well as information on its operation. The information that you get HP LASERJET P2055 will certainly help you make a decision on the purchase.
If you already are a holder of HP LASERJET P2055, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime HP LASERJET P2055.
However, one of the most important roles played by the user manual is to help in solving problems with HP LASERJET P2055. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device HP LASERJET P2055 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
