Instruction/ maintenance manual of the product P4014 HP
Go to page of 22
HP ® P4014 • P4015 • P4 045 CAR TRIDGE REMANUF ACTURING INSTRUCTIONS CC364X TONER CARTRIDGE CC364A TONER CARTRIDGE 3232 West El Segundo Blvd., Los Angeles, Calif ornia 90250 USA • Ph +1 31 0 280 9620 • Fx +1 3 10 838 7294 • techsupport@uninetimaging.
First introduced in April 2008, the HP LaserJet P40 1 4 engine is a 45-62 ppm (depending on the model), 1200 dpi engine. These printers will most lik ely replace the 4200/4300 series. All of the machines in all three series hav e a first page out in less than 8.
Right side of 64A Right side of 64X Lef t side of 64A Lef t side of 64X UNINET IMAGING INC . • BRO THER 1240/1650 • ASSEMBLING THE T ONER CARTRIDGE UNINET IMAGING INC . • BRO THER 1240/1650 • DISASSEMBLING THE T ONER CAR TRIDGE HP P4014, P4015 & P4045 CARTRIDGE REMANUF ACTURING INSTRUCTIONS 3232 West El Segundo Blvd.
UNINET IMAGING INC . • BRO THER 1240/1650 • ASSEMBLING THE T ONER CARTRIDGE UNINET IMAGING INC . • BRO THER 1240/1650 • DISASSEMBLING THE T ONER CAR TRIDGE HP P4014, P4015 & P4045 CARTRIDGE REMANUF ACTURING INSTRUCTIONS CAR TRIDGE THEORY 3232 West El Segundo Blvd.
In the first step, the Primar y Charge r oller (PCR) places a uniform negative DC Bias v oltage on the OPC drum sur face. The amount of the negative DC Bias placed on the drum is contr olled by the printer’s int ensity setting. This process is part of the latent Image formation block.
The third step (dev eloping block) is where the toner image is de veloped on the drum by the de veloping section, (or supply cham- ber), which contains the toner particles. The toner is held to the magnetic r oller sleeve b y the stationar y magnet inside the s lee ve, and a DC bias voltage supplied b y the high voltage power supply .
In the sixth step (fusing block) the image is then fused on t o the paper by the fuser assembly , which is comprised of the upper fixing film assembly and the lower fuser r oller . The paper passes between a heat ed upper fixing f ilm assembly and a soft lower rubber roller .
REQUIRED TOOLS 1. T oner appr oved v acuum 2. A small common screwdriv er 3. A Phillips head screwdriv er 4. Needle nose pliers SUPPLIES NEEDED 1. Dedicat ed P40 15 series toner: 465g f or the 64A & 1 065g for the 64X (preliminar y w eights) 2. Replacement drum 3.
1. Place the car tridge with the t oner hopper facing up and to wards you. This will orient the cartridge for right and left sides. 2. Open the drum cov er tow ards the back of the car tridge. Remo ve the right side metal bar . 3. On the opposite side of the cartridge, carefully pr y of f the drum cov er plastic arm.
6. Remo ve the five scre ws from the left end cap. 7 . Remo ve the right and left side end caps from the car tridge. Note that the gears do no t come of f the gear (right) end cap. 8. Separate the toner hopper and wast e chamber . 9. On the large gear side of the wast e chamber , remove the screw and whit e plastic drum bushing.
1 0. Remov e the drum. 11 . Remov e the PCR. 12. R emove the tw o screws from the wiper blade. 13. R emove the wiper blade fr om the car tridge and clean out the wast e toner . UNINET IMAGING INC . • BRO THER 1240/1650 • ASSEMBLING THE T ONER CARTRIDGE UNINET IMAGING INC .
1 4. Due to the high speed and page counts of these car- tridges, we recommend that the wiper blades be replaced. Make sure that the wiper blade f oam seals are clean. 15. Install the ne w wiper blade and two screws. 1 6. Clean the PCR with your standard PCR cleaner .
19. Install the drum small gear side first onto the drum axle pin 20. Install the white plastic drum bushing and scre w. If the OEM drum grease is dir ty , clean it off with alcohol, and replace with white lithium grease. 2 1. On the supply chamber , carefully pry of f the Magnetic roller (MRS) co ver , and remove.
23. Note the location of the spring that sits betw een the MRS holder and the hopper . Remo ve the two scre ws, spring and the holder . 2 4. Remo ve the MRS assembly . UNINET IMAGING INC . • BRO THER 1240/1650 • ASSEMBLING THE T ONER CARTRIDGE UNINET IMAGING INC .
25. Remo ve the two doct or blade screws and the doctor blade. No te the clear plastic strip that cov ers the DB screws. Slide the screwdriv er under the strip. Be careful not to damage the strip! 26. Remo ve the fill plug and clean out all the remaining toner in the supply hopper 2 7 .
28. Note also the ne w heavy duty style magnetic r oller contact. This when combined with the new larger diamet er of the roller , allow the cartridge to run at the higher speeds that these machines are capable of. 29. There are HP-4000 style magnetic roller bushings on each side of the r oller .
30. Unlike the HP-4300 series where there are three separat e mixing blades in the toner hopper . These car tridges just use one large mixing blade inside the toner hopper . 3 1. The upper mag. r oller section of the toner hopper is dif f er- ent in that is “Floats” on a series of foam seals.
34. Remo ve the right side small bushing from the magnetic roller slee ve and install it onto the holder . Make sure the tab on the bushing aligns with the slot in the holder . 35. Install the holder 2 screws and spring. Mak e sure the screw holes line up, and that the two locking tabs on the bo ttom of the holder are in the correct place.
36. Install the MRS drive gear . 3 7 . Install the key ed MRS cover . Make sure that the k eyed hole in the cov er matches the key ed end of the magnet in the MRS assembly . 38. Fill with appropriat e amount of P40 15 toner , install the fill plug. 39.
40. Install the right side end cap and five scre ws. 4 1. Install the remaining three screws on the left end cap. 42. Install the spring into the drum co ver arm as shown. Pull the upper tail of the spring until it fits into the notch in the arm hub. 43.
44. Install the arm onto the cartridge. Pull the arm fully back to release the spring fr om the notch. Check to mak e sure the drum cov er operates properly . 45. Remo ve the old chip from the t op of the car tridge by slic- ing the melted plastic off with a sharp X- Act o knife.
UNINET IMAGING INC . • BRO THER 1240/1650 • ASSEMBLING THE T ONER CARTRIDGE UNINET IMAGING INC . • BRO THER 1240/1650 • DISASSEMBLING THE T ONER CAR TRIDGE HP P4014, P4015 & P4045 CARTRIDGE REMANUF ACTURING INSTRUCTIONS 3232 West El Segundo Blvd.
An important point after buying a device HP HP P4014 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought HP HP P4014 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data HP HP P4014 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, HP HP P4014 you will learn all the available features of the product, as well as information on its operation. The information that you get HP HP P4014 will certainly help you make a decision on the purchase.
If you already are a holder of HP HP P4014, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime HP HP P4014.
However, one of the most important roles played by the user manual is to help in solving problems with HP HP P4014. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device HP HP P4014 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
