Instruction/ maintenance manual of the product 7038.400 American Standard
Go to page of 12
3 5 4 4 Cer tified to comply with ANSI A112.18.1 Installation Instructions Bidet Faucet and T ransfer V alve with Ev erClean™ Finish & SpeedC onnec t™ Drain Congr atulations on purchasing your A merican Standard faucet with E verClean finish and Speed Connect drain, two features f ound only on American Standard faucets.
M968893 POP-UP DRAIN Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 3 5 4 2 TIGHTEN LOCKNUT 1 REMOVE FLANGE Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body.
Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. 10 Connect water supply to V AL VE BODIES (7,7a) with 1/2" IPS FLEXIBLE SUPPLIES (8) or 3/8" O.
CHECK DRAIN CONNECTIONS 12 13 TEST INST ALLED FITTING With HANDLES (1) in OFF position, turn on W A TER SUPPLIES (2) and check all connections for leaks. Operate both HANDLES (1) to flush water lines thoroughly . Rotate TRANSFER V AL VE (5) from rim wash to spray several times to check operation.
M968893 SpeedConnect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration.
M968893 6 STOPPER INSTALLATION PROCEDURE Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper.
3 5 4 4 Cer tified to comply with ANSI A112.18.1 Installation Instructions Bidet Faucet and V acuum Br eaker with Ev erClean™ Finish & SpeedC onnec t™ Drain Congr atulations on purchasing your A merican Standard faucet with Ev erClean finish and Speed Connect drain, two featur es found only on American Standard fauc ets.
POP-UP DRAIN Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B. 3 5 4 2 TIGHTEN LOCKNUT 1 REMOVE FLANGE Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A. Thread LOCKNUT (3) clock-wise to bottom of drain body.
Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS. Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet. 10 Connect water supply to V AL VE BODIES (7,7a) with 1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8" O.
CHECK DRAIN CONNECTIONS 12 13 TEST INST ALLED FITTING With HANDLES (1) in OFF position, turn on W A TER SUPPLIES (2) and check all connections for leaks. Operate both HANDLES (1) to flush water lines thoroughly . Rotate TRANSFER V AL VE (5) from rim wash to spray several times to check operation.
SpeedConnect™ Drain Troubleshooting Guide Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A. Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration.
M968894 6 STOPPER INSTALLATION PROCEDURE Locked Mode: Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper.
An important point after buying a device American Standard 7038.400 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought American Standard 7038.400 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data American Standard 7038.400 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, American Standard 7038.400 you will learn all the available features of the product, as well as information on its operation. The information that you get American Standard 7038.400 will certainly help you make a decision on the purchase.
If you already are a holder of American Standard 7038.400, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime American Standard 7038.400.
However, one of the most important roles played by the user manual is to help in solving problems with American Standard 7038.400. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device American Standard 7038.400 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
