Instruction/ maintenance manual of the product C110 to C160 HP (Hewlett-Packard)
Go to page of 34
C100_110-160_180.FB -1 Tue Jul 16 06:36:50 1996 Installing the C100/C1 10 to C160/C180 CPU Upgrade HP Part No. A4200-90017 E0796 Printed in USA.
C100_110-160_180.FB 0 Tue Jul 16 06:36:50 1996 Hewlett-Packard Co. 1996 Printing History First Printing: July 1996 UNIX is a registered trademark in the United States and other countries, licensed exclusively through X/Open Company Limited. NOTICE The information contained in this document is subject to change without notice.
C100_110-160_180.FB 1 Tue Jul 16 06:36:50 1996 1 Upgrading your Model C100/1 10 to a Model C160 or C180 Upgrading your Model C100/110 to a Model C160 or C180 Y our upgrade kit contains a Main T ray Assembly , which, when installed, upgrades your Model C100/1 10 to a Model C160/C180.
C100_110-160_180.FB 2 Tue Jul 16 06:36:50 1996 2 Preparing Y our Workstation Preparing Your Workstation Before starting the upgrade, use the following procedure to prepare the workstation: 1 The workstation must be running HP-UX 10.20 or later to accommodate the C160/C180 upgrade.
C100_110-160_180.FB 3 Tue Jul 16 06:36:50 1996 3 Preparing Y our Workstation 4 Next, you need to run the upgrade utility program to automatically convert the hardware paths stored in the system’s I/O configuration file. You should only run this utility if you are going to complete the rest of the hardware upgrade described in this document.
C100_110-160_180.FB 4 Tue Jul 16 06:36:50 1996 4 Preparing Y our Workstation 5 If your system has an A4070B HCRX-8Z or an A4071B with the A4272A accel- erator graphics adapter installed enter the following commands to save the cur- rent versions of the /etc/ioconfig and /stand/ioconfig files: mv /etc/ioconfig /etc/ioconfig.
C100_110-160_180.FB 5 Tue Jul 16 06:36:50 1996 5 Preparing Y our Workstation 12 Unplug the power cord of the system unit, the monitor, and any peripheral devic- es from ac wall outlets.
C100_110-160_180.FB 6 Tue Jul 16 06:36:50 1996 6 Preparing Y our Workstation 14 Remove the floor stand from the system unit, as shown in Figure 1. Figure 1 Removing the Floor Stand 15 Lay the system unit on a flat surface, such as a table top. 16 Attach a static-grounding wrist strap to bare metal on the back of the system unit.
C100_110-160_180.FB 7 Tue Jul 16 06:36:50 1996 7 Removing the Main T ray Assembly Removing the Main Tray Assembly Once you have prepared the workstation, you need to remove the main tray from the system unit, as described in the following procedure: 1 Completely loosen the four thumb screws on the rear of the system unit, as shown in Figure 2.
C100_110-160_180.FB 8 Tue Jul 16 06:36:50 1996 8 Removing Memory Modules Removing Memory Modules After removing the main tray from the system, you must remove the mem- ory modules from the original C100/1 10 CPU board, as described in the fol- lowing procedure: 1 Locate the memory modules on the C100/C110 CPU board, as shown in Figure 3.
C100_110-160_180.FB 9 Tue Jul 16 06:36:50 1996 9 Removing Memory Modules 2 To remove a memory module, push the ejector tabs on each side of the module. Lift the memory module up and out of the connector and place it on a static-free surface. Figure 4 shows how to remove a memory module.
C100_110-160_180.FB 10 Tue Jul 16 06:36:50 1996 10 Removing Option Boards Removing Option Boards NOTICE: Any option boards that are supported by the new C160/180 system should be installed in the same slot number in the new main tray .
C100_110-160_180.FB 11 Tue Jul 16 06:36:50 1996 11 Removing Option Boards 2 Slide the EISA slider to the side to remove it, as shown in Figure 6. 3 Remove the screw from the EISA retainer, as shown in Figure 6 4 Grasp the option board by the edge with both hands and pull it straight out from its slot.
C100_110-160_180.FB 12 Tue Jul 16 06:36:50 1996 12 Installing Memory Modules Installing Memory Modules Install the memory modules in the C160/C180 CPU board in the new main tray , as described in the following procedure: 1 Locate the memory connectors on the C160/C180 CPU board, as shown in Figure 7.
C100_110-160_180.FB 13 Tue Jul 16 06:36:50 1996 13 Installing Memory Modules T able 1 Model C160/C180 Allowable Memory Configurations Config. No. Pair 0 Pair 1 Pair 2 Pair 3 Pair 4 Pair 5 T otal MB .
C100_110-160_180.FB 14 Tue Jul 16 06:36:50 1996 14 Installing Memory Modules 25 32 32 32 32 32 32 32 32 32 32 320 26 32 32 32 32 32 32 32 32 32 32 16 16 352 27 32 32 32 32 32 32 32 32 32 32 32 32 384 .
C100_110-160_180.FB 15 Tue Jul 16 06:36:50 1996 15 Installing Memory Modules 49 64 64 64 64 256 50 64 64 64 64 16 16 288 51 64 64 64 64 16 16 16 16 320 52 64 64 64 64 16 16 16 16 16 16 352 53 64 64 64.
C100_110-160_180.FB 16 Tue Jul 16 06:36:50 1996 16 Installing Memory Modules 73 64 64 64 64 64 64 32 32 32 32 32 32 576 74 64 64 64 64 64 64 64 64 512 75 64 64 64 64 64 64 64 64 16 16 544 76 64 64 64 .
C100_110-160_180.FB 17 Tue Jul 16 06:36:50 1996 17 Installing Memory Modules 2 To install a memory module, close the ejector tabs on each side of the memory connector and line the memory module up with the guides, as shown in Figure 8.
C100_110-160_180.FB 18 Tue Jul 16 06:36:50 1996 18 Installing Option Boards Installing Option Boards NOTICE: Any option boards that are supported by the new C160/180 system should be installed in the same slot number in the new main tray that they were installed in the old main tray .
C100_110-160_180.FB 19 Tue Jul 16 06:36:50 1996 19 Installing Option Boards Graphics Configuration Restrictions The system supports only four graphics displays at a time. A “display” is a video output port or connector . For example, the Dual V isualize Enhanced Graphics Card (A4451A) is a dual display card.
C100_110-160_180.FB 20 Tue Jul 16 06:36:50 1996 20 Installing Option Boards Option Board Installation If you removed option boards from the C100/1 10 main tray , use this proce- dure to install them in the new C160/C180 main tray . Otherwise, skip to the next section.
C100_110-160_180.FB 21 Tue Jul 16 06:36:50 1996 21 Installing Option Boards 2 Remove the screw from the EISA retainer, and remove the EISA retainer, as shown in Figure 10. Figure 10 Removing the EISA Retainer and EISA Slider 3 Remove the EISA slider, as shown in Figure 10.
C100_110-160_180.FB 22 Tue Jul 16 06:36:50 1996 22 Installing Option Boards 4 In the desired option slot, turn the blank plate’s locking knob counter-clockwise to unlock the plate, as shown in Figure 11. NOTE: The new main tray assembly contains a blank plate which is held in by a locking knob.
C100_110-160_180.FB 23 Tue Jul 16 06:36:50 1996 23 Installing Option Boards 6 Slide the option board into the slot. Make sure that the hole in the board’s handle aligns with the pin on the back panel, as shown in Figure 12.
C100_110-160_180.FB 24 Tue Jul 16 06:36:50 1996 24 Installing Option Boards 8 Replace the EISA retainer and its screw, as shown in Figure 13. 9 Replace the EISA slider, as shown in Figure 13 Figure 13.
C100_110-160_180.FB 25 Tue Jul 16 06:36:50 1996 25 Installing Option Boards 10 Rotate the fan back into place and firmly push it into the rear panel firmly until the clip snaps into place, as shown in Figure 14.
C100_110-160_180.FB 26 Tue Jul 16 06:36:50 1996 26 Installing the New Main T ray Assembly Installing the New Main Tray Assembly Install the new C160/C180 main tray assembly , as described in the following procedure: 1 Align the main tray assembly with the chassis and slide it into place, as shown in Figure 15.
C100_110-160_180.FB 27 Tue Jul 16 06:36:50 1996 27 Installing the New Main T ray Assembly 5 Remove any external SCSI terminators from the rear of the old main tray and in- stall them on the SCSI connectors on the rear of the system. 6 Use a small flat blade screwdriver to gently pry the old model number label from the front of the system.
C100_110-160_180.FB 28 Tue Jul 16 06:36:50 1996 28 Installing the New Main T ray Assembly 7 Replace the system unit in the floor stand, as shown in Figure 17.
C100_110-160_180.FB 29 Tue Jul 16 06:36:50 1996 29 Installing the New Main T ray Assembly 8 Reconnect the power cables and any other cables that you disconnected when opening the workstation.
C100_110-160_180.FB 30 Tue Jul 16 06:36:50 1996 30 Installing the New Main T ray Assembly 11 The system cycles through all of the available monitor types one at a time. When you can see a message similar to the following clearly and litigable, select that monitor type by pressing Enter.
C100_110-160_180.FB 31 Tue Jul 16 06:36:50 1996 31 Installing the New Main T ray Assembly 15 At the prompt, enter the following command to enter the configuration menu: co 16 Configure the console path for the built-in graphics with the following syntax: mo graphics(0) 17 Power off the system.
C100_110-160_180.FB 32 Tue Jul 16 06:36:50 1996 32 Installing the New Main T ray Assembly.
An important point after buying a device HP (Hewlett-Packard) C110 to C160 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought HP (Hewlett-Packard) C110 to C160 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data HP (Hewlett-Packard) C110 to C160 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, HP (Hewlett-Packard) C110 to C160 you will learn all the available features of the product, as well as information on its operation. The information that you get HP (Hewlett-Packard) C110 to C160 will certainly help you make a decision on the purchase.
If you already are a holder of HP (Hewlett-Packard) C110 to C160, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime HP (Hewlett-Packard) C110 to C160.
However, one of the most important roles played by the user manual is to help in solving problems with HP (Hewlett-Packard) C110 to C160. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device HP (Hewlett-Packard) C110 to C160 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
