Instruction/ maintenance manual of the product 500 HP (Hewlett-Packard)
Go to page of 8
HP DesignJet 500 and 800 Series Printers Assembly and Set-Up Instructions Contents of This Poster 1. Check the Cont ents of the Pack age (page 1) 2. Unpack the Main Component s (page 2) 3. Assemble the S tand (p age 2) 4. Attac h the S tand to the Pri nter (page 3) 5.
1–Rem ove: – (E+/A0 +-size m odel) The large box c ontaining the stand and paper bin. T w o peopl e may nee d to do this , as it ’ s rath er large. – The two pack ages con taining docu mentation, ca bles, etc . – The foam packaging that p rotects the ends of the pr inter .
7 – Remove the plastic covering and foam end cap s. 8 – Remove the ta pes from the window and the spindl e. Remove also the small bag of desicc ant material.
13 – Raise the bin into it s correct pos ition. Raise the bin unti l the l arge pins align wi th th eir slot s and the bin drop s into place. 1 – From the red document a tion p ackage (the “ inst allation p ack ” ) remove: – The Fron t-Panel ov erlay , for use in the next s tep.
The set-up printheads are provided to protect the ink syste m while the printer is being transport ed from the factory , and to fill up th e ink tubes i nside the printer when it is first ini ti alized. They must be replaced by act ive (normal) print heads when the printer ’ s tubes have filled with ink.
4 – Slide the new roll of p aper on to the spindle. Make sure t he orient ation of the p aper is loa ded exactly as shown. If i t is not, remove t he roll, turn it through 180 degrees ver tically a nd slide it back on to the spindl e. 5 – Put the removable stop on to the upper end of the spindle, and pus h it down as far as it will go.
NOTE: An internal HP JetDirect Print Serv er may already be installed i n your pr inter , inside the comp artment at t he top lef t rear of th e printer . If it is, skip to step 8 below . 1 – Before inst alling a card, switch off the printe r and unplug it from the mains electricity supply .
Use this CD Macintosh Direct C onnect (par al lel or USB cable) Printe r Yo u r P C 4. When yo u get to the Network Printer S e tup screen, select Direct Network Setup.
An important point after buying a device HP (Hewlett-Packard) 500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought HP (Hewlett-Packard) 500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data HP (Hewlett-Packard) 500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, HP (Hewlett-Packard) 500 you will learn all the available features of the product, as well as information on its operation. The information that you get HP (Hewlett-Packard) 500 will certainly help you make a decision on the purchase.
If you already are a holder of HP (Hewlett-Packard) 500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime HP (Hewlett-Packard) 500.
However, one of the most important roles played by the user manual is to help in solving problems with HP (Hewlett-Packard) 500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device HP (Hewlett-Packard) 500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
