Instruction/ maintenance manual of the product WM80 Hotpoint
Go to page of 20
Instruction Manual F or Models WM80, WM79, WM77, WM69, WM68, WM67, WM66 and WM60 Congratulations on the pur chase of your new W ashing Machine. IMPORT ANT INFORMA TION Please read this instruction book thoroughly before installing and using your appliance for the first time .
W ARNING: This appliance must be earthed. F uses Y our appliance comes fitted with a plug and a 13A fuse. If you need to replace the fuse , only those rated at 13A and AST A approv ed to BS1362 should be used.T o change fuse, lif t holder to vertical position and lift the fuse out.
Electricity Supply ...................................... 2 Recycling & Disposal Information .............. 3 Installation Instructions 1. Choose a L ocation................................ 4 2. Remo ve T ransit Bracket ....................... 5 3.
1. Choose a Loc ation... The choice of location f or your appliance will influence its pe rformance. ● Position wher e possible on a solid floor . Vibration may occur wi th a wooden floor . ● T ake care with vinyl floor coverings. The weight of the appliance may cause indenta tions in some vinyl floor co verings.
W ARNINGS ● Before using appliance, remove tr ansit bracket , clamp and screws Retain parts for future transportation. ● Do not remove concrete weight. Replace work top lid and 3 screws. Remove 2 screws and transit bracket, retain. Remove 1 screw and clamp , retain.
3. Connect to the W ater Supply ... ● Incoming hot and cold water pr essure should be between 3 and 150 psi (21 - 1034 Kpa). ● The temperatur e of the incoming household hot water supply shou ld ideally be 60°C and no higher than 70°C as this c ould cause damage to both your laundr y and appliance .
4. Connect to a Dr ainage Syst em... ● Do not remove hooked end support from drainage hose. ● Do not position standpipe near an electrical outlet. ● F or drainage into a standard work top sink ensure outlet pipe has a minimum bore of 32 mm. T o avoid syphoning ensure the end of the drainage hose is above the wat er level in the sink.
G etting t o K now Y our Applianc e Index Fro n t 1. Door Locked Indicator 2. Mains On/Off Button. 3. W ash Dial 4. V ariable Spin Speed Dial 5. Optional Wash F eature Buttons 2 available on Models WM80, WM 69, WM66 & WM60 4 available on Models WM79 WM77, WM68 & WM67 6.
Button Selection T o selec t, press button and button comes out. T o cancel, press again and button is flush with console. Interlocking Door System T o Open... Grip the door handle and press the button whilst pulling open the door (Fig 2). T o Close..
IMPORT ANT INFORMA TION: Before selecting a programme, ensure the ma ins button is in the ‘OFF’ position. Add detergen t and or conditioner to the dispenser drawer , see pages 14-15.
40 60 95 C A 40 95 3kg to 5.5kg 5.5kg ****1200rpm ***1150rpm **1100rpm *1000rpm 15 - 25 120 - 130 400rpm Prewash B D F E G J K H IMPORT ANT INFORMA TION: The temperature of the inc oming water sup ply or selection of wash features: ie. Economy , Super Rinse etc, will a ffect programme times.
Button Selection T o selec t an optional wash f eature, press button and a colour ba nd will become visible. Press again t o cancel. Option Buttons Economy W ash (for Models WM80, WM79, WM77, WM69, WM68, WM67 WM66 & WM60) Save money and time on lightly soiled loads.
W eight of W ash Load T wo examples of typical wash loads for different types of fabric C OT T ON 2 Bath T owels 5 Shirts 6 Blouses 1 Set of Pyjamas 4 Sets of Under wear = 5.5kg SYNTHETIC 2 Children ’ s Dresses 4 Shirts 4 Blouses 1 Set of Pyjamas 4 Sets of Under wear = 3kg W ashcar e Tips Before washing laundry :- ● Pre-tr eat stains.
The Dispenser Dr awer Choose a Suitable Detergent ● Hotpoint recommend the P ersil range of detergent products. ● Select ‘low suds’ automatic powder , designed specifically for aut oma tic washing machines or washer/dryers. ● F ollow manufacturer ’ s dosage recommendations.
T o obtain claimed energy label wash performance for a 60°C cotton wash, dispense powder detergent in a dosing ball, placed in an upright position in the centre of the wash load (F ig 5).
Removing and Cleaning the Dispenser Draw er & Compartments Note: It is advisable to clean the dispenser drawer regularly . Re-locate dispenser drawer and push firmly back into place.
T roubleshooting ... If the appliance is still not working contact: Ser vice UK: 08709 066 066 Republic of Ireland:1850 302 200 you will be asked for the follo wing information:- ● Name, address and.
18 Hotpoint appliances carry for the first 12 months a fully inclusive parts and labour guarantee plus FREE replacement parts for the first 5 years provided tha t they are fitted by our own Ser vice Engineer .
Fr om the moment your appliance is delivered , Hotpoint guarantees it f or five years. ● Hotpoint appliances carry a fully inclusive 12 months parts and labour guarantee plus FREE replacement parts for the first five years provided tha t they are fitted by our own Service Engineer (evidence will be required of date and place of purchase).
Key C ontac ts Ser vice UK: 08709 066 066 Republic of Ireland: 1850 302 200 Y ou will be asked to quote the Model Number and Serial Number, which can be found on the inside of the door .
An important point after buying a device Hotpoint WM80 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hotpoint WM80 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hotpoint WM80 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hotpoint WM80 you will learn all the available features of the product, as well as information on its operation. The information that you get Hotpoint WM80 will certainly help you make a decision on the purchase.
If you already are a holder of Hotpoint WM80, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hotpoint WM80.
However, one of the most important roles played by the user manual is to help in solving problems with Hotpoint WM80. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hotpoint WM80 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center