Instruction/ maintenance manual of the product NLL113 Hotpoint
Go to page of 24
Hotpoint.com NLL113 NVL333 Dr y ers 134204000 175D1807P417 39-90153 11-02 JR Safety Instr uctions . . . . . . . . . 2–4 Operating Instr uctions Control Panels . . . . . . . . . . . . . . . .5 Control Settings . . . . . . . . . . . . . . .5 Loading and Using the Dryer .
IMPORT ANT SAFETY INFORMA TION. READ ALL INSTRUCTIONS BEFORE USING. ■ Properly ground dryer to conform with all governing codes and ordinances. Follow details in the Installation Instructions section. ■ Install or store where it will not be exposed to temperatures below freezing or exposed to the weather .
■ Never reach into the dryer while the drum is moving. Before loading, unloading or adding clothes, wait until the drum has completely stopped. ■ Clean the lint filter before each load to prevent lint accumulation inside the dryer or in the room. DO NOT OPERA TE THE DR YER WITHOUT THE LINT FIL TER IN PLACE, UNLESS THE DR YING RACK IS IN USE.
4 WHEN USING YOUR DRYER (cont.) ■ Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug. ■ The interior of the machine and the exhaust duct connection inside the dryer should be cleaned at least once a year by a qualified technician.
5 About the control panel. Hotpoint.com Y ou can locate your model number on the label on the front of the left side of the door opening. Model NVL333 OFF LESS DRY Model NLL113 1 2 1 2 Consumer Suppor.
6 The Exterior: Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer . The fabric may then be washed and dried normally .
7 Machine wash cycle Normal Permanent Press/ wrinkle resistant Gentle/ delicate Hand wash Do not wash Do not wring Water temperature Hot (50 ° C/120 ° F) Warm (40 ° C/105 ° F) Cold/cool (30 ° C/8.
Prepare the area and exhaust for installation of the new dryer . Check to be sure that the existing external exhaust is clean and that it meets attached installation specifications. Using the four shipping carton corner posts as padding (two on each side), carefully lay the dryer on its left side and remove foam shipping pad.
9 Electrical Connection Information for Gas Dryers W ARNING — T o reduce the risk of fire, electric shock or personal injury: • DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE. • DO NOT , UNDER ANY CIRCUMST ANCES, CUT OR REMOVE THE THIRD GROUNDING PRONG FROM THE POWER CORD.
If all rigid metal duct cannot be used, then flexible all-metal venting can be used, but it will reduce the maximum recommended duct length. In special installations when it is impossible to make a co.
Replace brass connecting pipe that is not plastic-coated. Stainless steel or plastic-coated brass MUST be used. W ARNING: Never reuse old flexible connectors. The use of old flexible connectors can cause gas leaks and personal injury . Always use NEW flexible connectors when installing a gas appliance.
12 Do Not Install the Dryer: Do not install the dryer in an area exposed to dripping water or outside weather conditions. Do not install the dryer in an area where it will come in contact with curtains, drapes or anything that will obstruct the flow of combustion and ventilation air .
13 Rough-In Dimensions Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal ducting must be 4 ″ (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred.
14 DANGER: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded.
Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner . Install a UL-approved strain relief into the power cord entry hole of the mounting bracket. Use a strain relief which attaches to the mounting bracket with a nut.
16 Remove the shipping cap from gas pipe at the rear of the dryer . NOTE: DO NOT connect the dr yer to LP gas ser vice without converting the gas valve. An LP conversion kit (Pub. No. 14-A038) MUST be installed by a qualified gas technician. Connect a 1/2 ″ (1.
17 Reversing the Dryer Door Swing Open the dryer door . Remove the 4 hinge hole plugs or screws from the left side of door opening. Place nearby for future installation. NOTE: Y ou may need a plastic knife to help pull out the plugs. Be careful not to scratch the paint.
Problem Possible Causes What T o Do Dryer doesn’t start Dr yer is unplugged • Make sure the dryer plug is pushed completely into the outlet. Fuse is blown/circuit breaker • Check the household Distribution Panel fuse/circuit is tripped breaker box in your home, and replace fuse or reset breaker .
19 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions Hotpoint.com Problem Possible Causes What T o Do Inconsistent T ype of heat • Automati.
20 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions Notes..
General Electric Company W ar ranty Registration Depar tment P .O. Box 32150 Louisville, KY 40232-2150 GE Ser vice Protection Plus ™ GE, a name recognized worldwide for quality and dependability , o.
Consumer Pr oduct Ownership Registration I m p o r t a n t M a i l T o d a y ! General Electric Company Louisville, Kentucky GEAppliances.com First Name Mr . ■ ■ Ms. ■ ■ Mrs. ■ ■ Miss ■ ■ Street Address City State Date Placed In Use Month Day Y ear Zip Code Apt.
23 For The Period Of: W e Will Replace: One Y ear Any part of the dr yer which fails due to a defect in materials or workmanship. During this From the date of the full one-year warranty , we will also provide, free of charge, all labor and in-home ser vice to original purchase replace the defective part.
Printed in the United States Consumer Support. Hotpoint W ebsite Hotpoint.com Have a question or need assistance with your appliance? T r y the Hotpoint W ebsite 24 hours a day , any day of the year! Y ou can also shop for more great Hotpoint products and take advantage of all of our on-line support services designed for your convenience.
An important point after buying a device Hotpoint NLL113 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hotpoint NLL113 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hotpoint NLL113 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hotpoint NLL113 you will learn all the available features of the product, as well as information on its operation. The information that you get Hotpoint NLL113 will certainly help you make a decision on the purchase.
If you already are a holder of Hotpoint NLL113, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hotpoint NLL113.
However, one of the most important roles played by the user manual is to help in solving problems with Hotpoint NLL113. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hotpoint NLL113 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
