Instruction/ maintenance manual of the product KML-450MAH Hoshizaki
Go to page of 22
ISSUED: HOSHIZAKI MODULAR CRESCENT CUBER INSTR UCTION MANU AL FEB. 21, 2001 MODELS KML-450MAH KML-450MWH REVISED: SEPT . 24, 2001 TM.
2 HOSHIZAKI AMERICA, INC. 618 Highway 74 South Peachtree City , GA 30269 Attn: HOSHIZAKI T echnical Support Department Phone: 1-800-233-1940 T echnical Service (770) 487-2331 Fax: (770) 487-3360 NO TE.
3 • Please review this manual. It should be read carefully before the icemaker is installed and operated. Only qualified service technicians should install, service and maintain the icemaker. This manual should be made available to the technician prior to installation, maintenance or service.
4 I. SPECIFICA TIONS 1. NAMEPLA TE RA TING [a] KML-450MAH (Air-cooled) See the Nameplate for electrical and refrigeration speci- fications. This Nameplate is located on the upper right hand side of the rear panel.
5 [b] KML-450MWH (Water-cooled) See the Nameplate for electrical and refrigeration speci- fications. This Nameplate is located on the upper right hand side of rear panel. Since this Nameplate is located on the rear panel of the icemaker, it cannot be read when the back of the icemaker is against a wall or against another piece of kitchen equipment.
6 2. DIMENSIONS/CONNECTIONS [a] KML-450MAH Unit: inches (mm.).
7 [b] KML-450MWH Unit: inches (mm.).
8 II. INST ALLA TION AND OPERA TING INSTR UCTIONS 1. CHECKS BEFORE INST ALLA TION IMPORT ANT Remove shipping carton, tape(s) and packing. If packing material is left in the icemaker, it will not work properly. 1) Remove the panels to prevent damage when installing the icemaker.
9 2. HOW TO REMOVE PANELS - See Fig. 1 a) Front Panel ......... Remove the screw. Lift up and pull toward you. b) Top Panel ............ Lift its front up slightly, push away, and then lift off. c) Side Panel (R) ..... Remove the screw. Pull slightly toward you, and lift off.
10 4. SET UP 1) Unpack the Storage Bin, and attach the four adjustable legs provided (bin accessory) to the bottom of the Storage Bin. 2) Position the Storage Bin in the selected permanent position. 3) Place the icemaker on the top of the Storage Bin.
11 6. W A TER SUPPL Y AND DRAIN CONNECTIONS - See Fig. 4 IMPORT ANT Do not operate the icemaker when the water supply is OFF, or if the pressure is below 10 PSIG. Do not run the icemaker until the proper water pressure is reached. • Water supply inlet is 1/2" female pipe thread (FPT).
12 Fig. 4 KML-450MWH KML-450MAH.
13 7. FINAL CHECK LIST 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within +45°F to +100°F and the water temperature within +45°F to +90°F all year aroun.
14 8. ST AR T UP CAUTION 1. All parts are factory-adjusted. Improper adjustments may result in failure. 2. If the unit is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the Compressor. 3. Do not operate the unit in the “WASH” position without water in the Water Tank.
15 Note: The Bin Switch will only shut down the unit at the end of a harvest or within the first 5 minutes of the freeze cycle. To shut the unit down outside of this time period turn the control switch to “OFF”. 8) Replace the Bin Control Cover. 9) Move the Control Switch to the “Service” position.
16 9. PREP ARING THE ICEMAKER FOR LONG ST ORA GE CA UTION When shutting off the icemaker for an extended time, drain out all water from the water line and remove the ice from the Storage Bin.
17 [2] Remove the water from the potable water supply line: 1) Turn off the power supply and remove the Front Panel. 2) Move the Control Switch, on the Control Box, to the “OFF” position. 3) Wait 3 minutes. 4) Close the Potable Water Supply Line Shut-off Valve and open the Potable Water Supply Line Drain Valve.
18 III. CLEANING AND MAINTENANCE INSTR UCTIONS 1. CLEANING INSTR UCTIONS W ARNING 1. HOSHIZAKI recommends cleaning this unit at least once a year. More frequent cleaning, however, may be required in some existing water conditions. 2. To prevent injury to individuals and damage to the icemaker, do not use ammonia type cleaners.
19 10) Move the Service Switch to the “WASH” position. 11) Replace the Insulation Panel and the Front Panel in their correct positions. 12) Turn on the power supply and start the washing process. 13) Turn off the power supply after 30 minutes. 14) Remove the Front Panel.
20 Note: If you do not sanitize the icemaker, go to step 14) in “SANITIZING PROCEDURE.” [b] SANITIZING PROCEDURE - Following Cleaning Procedure 1) Dilute IMS-II Sanitizer or a 5.25% Sodium Hypochlorite solution with water (Add 1.0 fl. oz. to 2 gal.
21 2. MAINTENANCE IMPORT ANT This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. 1) Stainless Steel Exterior To prevent corrosion, wipe the exterior occasionally with a clean and soft cloth.
22 91A1BE10B HOSHIZAKI HOSHIZAKI AMERICA, INC. 618 HIGHW A Y 74 SOUTH PEA CHTREE CITY , GA 30269 U .S.A. PHONE: 770-487-2331.
An important point after buying a device Hoshizaki KML-450MAH (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hoshizaki KML-450MAH yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hoshizaki KML-450MAH - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hoshizaki KML-450MAH you will learn all the available features of the product, as well as information on its operation. The information that you get Hoshizaki KML-450MAH will certainly help you make a decision on the purchase.
If you already are a holder of Hoshizaki KML-450MAH, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hoshizaki KML-450MAH.
However, one of the most important roles played by the user manual is to help in solving problems with Hoshizaki KML-450MAH. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hoshizaki KML-450MAH along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
