Instruction/ maintenance manual of the product DT-400BAH-OS Hoshizaki
Go to page of 21
Hoshizaki “A Superior Degr ee of Reliability” www .hoshizaki.com Model DT-400BAH-OS Cubelet Icemaker / Dispenser Hoshizaki America, Inc. Issued: 2-28-2008 Revised: 6-14-2010 I N S T R U C T I O N .
2 IMPOR T ANT Only quali ed ser vice technicians should at t empt t o install, service, or maintain this icemaker . No installation, service, or maintenance should be under tak en until the technician has thor oughly r ead this Instruction Manual.
3 IMPOR T ANT This manual should be r ead car efull y bef ore the icemak er is installed and operat ed. Only quali ed ser vice technicians should inst all, ser vice, and maintain the icemak er . Read the w ar nings contained in this booklet car efully as they giv e impor tant inf or mation r eg ar ding saf et y .
4 I. Specications A. Nameplate Rating HOSHIZAKI ICE MAKER MODEL NUMBER DT-400BAH-OS SERIAL NUMBER AC SUPPLY VOLTAGE 115-120/60/1 AMPERES 10.0 DESIGN PRESSURE HI-460PSI LO-290PSI REFRIGERANT 404A 1 LB 1 OZ MOTOR-COMPRESSOR THERMALL Y PROTECTED, NOT INTENDED FOR OUTDOOR USE! Hoshizaki America, Inc.
5 B. Dimensions / Connections Unit: mm [inch].
6 II. Installation and Operating Instr uctions A. Checks Bef ore Installation IMPOR T ANT 1 . Install in accor dance with all applicab le national, stat e, and local regulations . 2. Ensure all components, f astener s, and thumbscre ws are secur el y in place af ter installation.
7 C. Location C A UTION 1 . This icemaker is not int ended for outdoor use . Nor mal operating ambient temper atur e should be within +45°F t o +1 00°F (+7°C to +38°C); Nor mal operating w at er t emperatur e should be within +45°F to +90°F (+7°C to +32°C).
8 E. Electrical Connection See F ig. 2 W ARNING The GREEN gr ound wir e in the f actor y -installed pow er cor d is connect ed to a scr ew on the brac ket wher e the cor d ent er s the machine. If it becomes necessar y t o r emov e or replace the po wer cor d, be sure to connect the po wer cord’ s gr ound wir e to this scr ew upon r eat tachment.
9 F . W ater Suppl y and Dr ain Connections See F ig. 3 C A UTION T o pre vent damage t o the equipment, do not operat e this icemaker when the wat er supply is of f, or if the pr essure is belo w 1 0 PSIG. Do not r un the icemaker until the pr oper wat er pr essure is r eached.
1 0 G. F inal Chec klist 1) Is the icemaker le v el? 2) Is the icemaker in a sit e where the ambient t emperatur e is within +45°F to +1 00°F (+7°C to +38°C) and the w ater t emperatur e is within.
1 1 H. Star t up C A UTION 1 . All par ts are f actor y -adjusted. Improper adjustments ma y result in f ailure . 2. If the icemaker is tur ned of f , w ait f or at least 3 minut es befor e restar ting the icemaker t o pre vent damage t o the compr essor .
1 2 Contr ol Switch ("ICE", "OFF" or "DRAIN") Dispense Mode S witch ("POR TION" or "CONTINUOUS") Dispense Ice Sensor Dispense W at er Sensor Fig. 5 P ow er S witch "ON" and "OFF" Agit at or Mot or Dispensing Motor Fig.
1 3 I. Controls and A djustments 1 . P or tion Contr ol A v ariable r esist or which contr ols the amount of ice dispensed is locat ed on the contr ol board. The gures on the label indicat e dispensing time (sec.). When shipped, the por tion control is set at the minimum dispensing time (0.
1 4 III. Cleaning and Maintenance IMPOR T ANT Ensure all components , fast eners and thumbscre ws are secur el y in place af ter any maint enance or cleaning is done to the equipment. W ARNING 1 . Hoshizaki recommends cleaning this icemak er at least t wice a y ear .
1 5 8) Allow the icemak er to sit f or about 1 0 minutes bef ore oper ation. If you placed a clamp on the reservoir hose in st ep 7 , r emov e it befor e operation. 9) Plug the icemaker bac k in. Mov e the power s witch to the "ON" position and r eplace the panels in their correct positions .
1 6 8) Mov e the control s witch to the "OFF" position. Remo v e the upper fr ont, t op and lef t side panels. 9) Mov e the power s witch to the "OFF" postion.
1 7 Fig. 8 Fig. 9 B. Cleaning and Sanitizing Instructions - Dispensing Components P erf orm follo wing the cleaning and sanitizing pr ocedur es f or the water s yst em.
1 8 9) Immerse the parts remov ed in steps 4 thr ough 8 in the cleaning and sanitizing solutions f or about 1 5 minut es each. 1 0) Rinse these par ts thoroughl y with clean water . 1 1) Thor oughl y wipe the shut ter locat ed abov e the ice dispensing spout.
1 9 C. Maintenance IMPOR T ANT 1 . This icemaker m ust be maintained individuall y , r ef err ing to the instruction manual and labels pr o vided with the icemak er .
20 D . P reparing the Icemak er for Long St ora ge W ARNING When the icemak er is not used for t wo or thr ee day s under nor mal conditions, it is suf ficient t o onl y mov e the control s witch to the "OFF" position.
21 HOSHIZAKI AMERICA, INC. 618 Hwy . 74 S., Peachtree City , GA 30269 USA TEL (770) 487-2331 F AX (770) 487-3360 www .hoshizaki.com 91A2KB10C.
An important point after buying a device Hoshizaki DT-400BAH-OS (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hoshizaki DT-400BAH-OS yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hoshizaki DT-400BAH-OS - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hoshizaki DT-400BAH-OS you will learn all the available features of the product, as well as information on its operation. The information that you get Hoshizaki DT-400BAH-OS will certainly help you make a decision on the purchase.
If you already are a holder of Hoshizaki DT-400BAH-OS, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hoshizaki DT-400BAH-OS.
However, one of the most important roles played by the user manual is to help in solving problems with Hoshizaki DT-400BAH-OS. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hoshizaki DT-400BAH-OS along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
