Instruction/ maintenance manual of the product WindTunnel Hoover
Go to page of 14
Self-Propelled WindTunnel’” WARRANTY (See Copy Where Product Sold) v l with Powered Hand Tool by HOOVER This WindTunnel’” vacuum cleaner takes HOOVER@ Type “Y” Allergen Filtration filter b.
Owner’s Manual ENGLISH + pp.l-14 ESPA6lOL + pig. 15-22 FRANCAtS -+ p. 23-30 Review this manual before operating cleaner 1 Fill in and retain The model and serial number are located on the back of the handle as shown. For your personal records, please enter the COMPLETE model and serial number in the spaces provided and retain this information.
Index Assembling Cleaner ............................................................ 3-4 Carton Contents .................................................................. 3 How To Use Cleaner Descriptions ............................................
Looking at the back of the cleaner, make sure switch (A) is in the OFF position. Slide handle into back of cleaner. Push screws into holes on back of handle. Using a Phillips screw driver, tighten screws securely. Remove switch lock (B) above ON- OFF switch (C) on front of handle by pulling it straight out.
Cleaner description 184 The assembled cleaner will look like the drawing. 1. Handle 2. Self-propel button 3. ON-OFF switch 4. Hose 5. Tool cover 6. Powered hand tool 7. Final filter door 8. Handle release lever: step on lever to lower handle to operating or low positions.
Carrying cleaner The cleaner can be moved by using the carrying handle located on the back of the cleaner. Handle positions The handle of your cleaner has three positions; upright for storage and when using cleaning tools; operating posi- tion for general operation on carpet and floors; low for reaching under low furniture.
BRUSH ROLL Automatic brush roll Cleaning lightweight indicator flexible rugs _ When red is in the OFF window, brush Stand on one end ot rug anu move roll is STOPPED. cleaner toward other end or edge. When red is in the ON window brush roll Before reaching edge, push down on is ROTATING.
G D Check bag indicator (some models only) The indicator (I) will begin to show red as the filter bag fills with dirt. There are three conditions that will cause the indicator to become completely red: 1. If the bag is full; change the bag. 2. If very fine materials have been picked up, clogging the bag pores; change the bag.
Replacing bag door Reposition bag door by placing tab on bottom of door into opening (C). Press top of door to snap securely shut. Secondary and final filters Cleaning secondary filter Disconnect cleaner from electrical outlet.
Removing belt Flat belt (B) operates the self-propel fea- ture and indirectly drives the brush roll. Remove used belt (B) from large pulley (C) and discard. Belt replacement The belts are located under the bottom plate of the cleaner and should be checked from time to time to be sure they are in good condition.
Replacing brush roll Removing brush roll Slide Brush Roll Control (Fig. 2-9) to “Hard” (OFF) position. Turn cleaner over and remove bottom plate (Fig. 3-9). Lift up brush roll and slide V-belt (D) off brush roll. Inspecting V-belt The V-belt is designed to last for a long time and is not normally replaced.
6. With curved ends down, slide end plates (C) of brush roll into slots (E) on tool. 7. Replace belt guard (B) making sure not to pinch brush bristles in guard. Turn agitator, making sure it rotates freely. Replace and tighten screws. 8. To replace bottom plate (A), insert the four tabs on edge of bottom plate into slots on front of tool.
Service To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: l checking the Yellow Page.
Checking under bottom plate 5. Remove bottom plate ( Fig. 3-9) and brush roll (Fig. 3-15). Look into opening (F), in channnels (G) and around liner (H), and remove any accumulated debris, If blockage occurs during powered hand tool use 1. Disconnect powered hand tool from hose.
An important point after buying a device Hoover WindTunnel (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hoover WindTunnel yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hoover WindTunnel - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hoover WindTunnel you will learn all the available features of the product, as well as information on its operation. The information that you get Hoover WindTunnel will certainly help you make a decision on the purchase.
If you already are a holder of Hoover WindTunnel, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hoover WindTunnel.
However, one of the most important roles played by the user manual is to help in solving problems with Hoover WindTunnel. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hoover WindTunnel along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
