Instruction/ maintenance manual of the product U5361950 Hoover
Go to page of 14
HOOVER ® Thank you for your pur chase! Bagless Upright ® This product was designed for easy assembly (see page 3) www .hoover .com ENGLISH ➜ pp. 1-14 ESP AÑOL ➜ pág.
2 Thank you for choosing a HOOVER ® pr oduct. Please enter the COMPLETE model and serial numbers in the spaces provided. The numbers are located on the bottom of your cleaner . Model_________________________________________ Serial number_________________________________________ Hint: Attach your sales receipt to this owner’s manual.
3 1. Cleaner Assembly If you need any assistance: V isit our website at www .hoover .com . Click on the “Service” button to find the service outlet near est you OR Call 1-800-944-9200 for an automated r eferral of service outlet locations (U.S. only) OR Call 1-330-499-9499 to speak with a r epr esentative in our Consumer Response Center .
C 4 Align end of hose with projections (A) over slots (B) in dirt duct. Slide hose into duct (B) and twist hose to lock it into place. Snap ends of dusting brush (A), crevice tool (B) and furniture nozzle (C) into clips as shown. 1-10 1-5 1-8 1-6 1-7 1-9 1-12 Place nuts in recessed ar eas on front of handle.
5 Continued ➜ 1. Handle 2. Cord hooks: wrap cord around hooks for storage. The top hook rotates right or left for easy cord release. 3. Hose 4. ON/OFF switch: located on left rear corner of cleaner body 5. Carrying handle 6. Stair cleaning handle: located on lower edge of dirt cup.
Handle position For ease in sliding knob, place handle in the upright position (C). The nozzle will not move into the adjusted position until the cleaner handle is lowered to the operating position (D). Settings For maximum cleaning performance, the following carpet height settings are recommended.
7 Edge cleaning Edge cleaning is provided on both sides of the nozzle to remove dirt in carpet near baseboards and furniture. Guide either side of nozzle parallel to edge of carpet or furniture. Cleaning tools T ools allow for cleaning surfaces above the floor and for reaching har d to clean areas.
3. Maintenance When to empty It is recommended that the dirt cup be emptied before the dirt reaches the dirt opening on back of dirt cup (Fig. 3-1) or after every use if preferred. CAUTION: V ery fine materials, such as face powder or cornstarch, may seal the filter and cause loss of suc- tion.
9 3-10 3-6 3-5 3-7 3-8 3-9 3-11 Pull up on pre-filter assembly . Slide it out of cup. Replace dirt cup. Filter assembly How to clean filter assembly Remove dirt cup and dir t cup lid as described in “How to empty dirt cup”. Pivot pre-filter assembly towar d center of cup.
G Remove lens - Disconnect clean- er from electrical outlet. Using a screwdriver , remove the two screws as shown and lift of f lens. 3-16 3-15 10 Secondar y and final filters Cleaning secondary filter Disconnect cleaner from electrical outlet.
11 Continued ➜ 3-17 3-18 Remove agitator brush roll Remove agitator and used belt. Discard used belt. Replace lens - Reposition lens and secure with the two scr ews. How to replace Disconnect cleaner from electrical outlet. Remove bottom plate Place handle in low position and turn cleaner over so bottom side is up.
12 3-24 3-25 The agitator brush roll When to replace When agitator brushes are worn, the agitator should be replaced. T o check condition of brushes, discon- nect cleaner from electrical outlet. Move edge of a card acr oss bottom plate while turning agitator .
D 13 Clearing blockages Disconnect cleaner from electrical outlet. Low suction or pick up may be due to a blockage in the system. Refer to the fol- lowing steps to check for blockages continuing with each step until the blockage is found: T urn cleaner OFF and disconnect from electrical outlet.
14 Full One Y ear W arranty (Domestic Use) Y our HOOVER ® appliance is warranted in normal household use, in accordance with the Owner’ s Manual against original defects in material and workmanship for a period of one full year from date of purchase.
An important point after buying a device Hoover U5361950 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hoover U5361950 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hoover U5361950 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hoover U5361950 you will learn all the available features of the product, as well as information on its operation. The information that you get Hoover U5361950 will certainly help you make a decision on the purchase.
If you already are a holder of Hoover U5361950, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hoover U5361950.
However, one of the most important roles played by the user manual is to help in solving problems with Hoover U5361950. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hoover U5361950 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
