Instruction/ maintenance manual of the product Shampoo-Polisher Hoover
Go to page of 22
Review this manual before operating appliance : . . . . . :t.
This cleaner was inspected and packaged carefully before being shipped from the factory. If you should happen to need assistance during assembly or operation, call l-800-944-9200 for automated referral of authorized service outlet locations (U.S. only) or l-330-499-9499 to speak with a representative in our Consumer Response Center.
IMPORTANT SAFEGUARDS! When using an electrical appliance, always follow basic precautions, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE To reduce the risk of fire, electric shock, or WARNING: injury Use indoors only. This appliance is provided with double insulation.
Unpacking Unpacking Unpack the shampoo-polisher Unpack the shampoo-polisher and identify the accessories and identify the accessories shown. Remove and shown.
, 1 Questions or Concerns? ; The Hoover Company wants to quickly resolve any concerns about your i cleaner or questions regarding its use. Look on the list provided with the .
Assembly 1. Remove tank from shampoo- polisher and remove nut, bolt and cord clip from top of lower han- dle section. 2. Join upper and lower handles, lining up holes. Place cord clip around cord with flat side toward handle and holes to front. 3. Insert bolt through cord clip, and through small holes of han- dle; secure with nut.
To attach pads, insert end of fastener through opening in pad. Place pad over scrubbing-wax- ing-polishing brushes only. The fastener fits around the brush shaft. Press the fastener to snap into place. Unsnap fastener to remove pad. To attach tank Attach brushes and pads before attaching tank.
To dispense solution Squeeze trigger to dispense cleaning solution onto carpet, rug or floor. To remove tank Turn tank cap lock until the rivet is directly above slot. Lift up lock and tank cap. Pull top of tank forward; lift tank from shampoo-polisher.
Before you begin 1. Test for colorfastness Apply some shampoo solution to a small inconspicuous area of the carpet and rub with a white cloth. Check to see that color does not come off on the cloth and that the color of the carpet is satisfactory after the area dries.
Using the shampoo polisher 1. Attach shampoo brushes. Do not use scrubbing-waxing- polishing brushes on carpet or rugs. (Shampoo brushes are very soft to protect fine rugs and carpet.) 2. Fill tank Prepare shampoo solution fol- lowing directions on container.
. . foam. Crisscross area to work foam uniformly into the carpet (see illustration) until the foam disappears. The final strokes over each area should always be in the same direction. Repeat the process over another 3 ft. x 3 ft. area (Im x Im), overlapping the areas bv several inches.
Cleaning floors t There are two methods of cleaning hard surface floors: 1. Water method - used for all floors that can be cleaned with soap or detergent and water solution. 2. Solvent or solvent cleaning wax method - used for wood and sealed .’ .’ cork floors that may be damaged by water solutions.
Check this chart for floor care methods recommended for your floor. , Floors Cleaning method Wax* Wood Solvent cleaning wax Solvent-Base method - Use solvent base liquid wax. Linoleum Water method - Use mild soap or deter- gent and water solu- tion. Water-Base Rubber tile Water method - Clean Water-Base with detergent or soap and water solu- tion.
i Check this chart for floor care methods recommended for your floor. t : Floors Cleaning method Wax* Wood Linoleum Solvent cleaning wax Solvent-Base method - Use solvent base liquid wax. Water method - Use Water-Base mild soap or deter- gent and water solu- tion.
Solvent cleaning wax method I .I Wood and sealed cork floors may be damaged by using water solutions; 2 therefore, use only those cleaners and waxes recommended specifically ‘I for wood or cork. The following directions are for cleaning wood or cork floors with a cleaning polishing solvent base liquid wax.
FLOOR WAX Solvent Base There are two kinds of solvent- base wax: paste wax and liquid polishing wax. Paste wax To spread wax evenly, attach scrubbing-waxing-polishing brushes to shampoo-polisher and snap on cleaning-waxing pads. Spread a thin coat of wax on pads or spread a small amount on floor with spatula.
To achieve a high lustre finish 1. Attach felt buffing pads over scrubbing-waxing-polishing brushes using ,’ fasteners. Polish to a soft shine by guiding shampoo polisher in straight lines ’ or with the grain of the wood. If more shine is desired proceed to step 2.
Shampooer base Remove brushes and dry bottom of shampoo-polisher with a paper towel or cloth before storing. Brushes The brushes need to be washed in warm water and detergent to remove wax. Rinse well. Shake to remove excess water. To dry, place on paper towels with brushes turned toward towels.
If you have a problem This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory. If a minor problem occurs it usually can be solved quite easily when the cause is found. Therefore, this check list is provided for your convenience.
3 ? / < -3 -, : t I. Servicing of Double-Insulated Appliances This appliance is double insulated. In a double-insulated appliance, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated appliance, nor should a means for grounding be added.
Floor care hints Floors may be difficult to care for when not treated properly. Refer to the chart below for solutions to floor problems. Problem Cause Solution ZiJ)“W Too much wax. Remove wax. Apply thin even coat. Detergent not rins- Remove wax. Rinse detergent from ed from floor.
:. ,. .^” Accessories (Available at your Hoover Dealer (Depot) or Hoover Factory Service Center at a slight additional cost.) ;. Steel wool pads for applying sol- High lustre polishing pads for vent-base paste wax. Snap on over scrubbing-waxibg-polishing polishing furniture and floors.
An important point after buying a device Hoover Shampoo-Polisher (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hoover Shampoo-Polisher yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hoover Shampoo-Polisher - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hoover Shampoo-Polisher you will learn all the available features of the product, as well as information on its operation. The information that you get Hoover Shampoo-Polisher will certainly help you make a decision on the purchase.
If you already are a holder of Hoover Shampoo-Polisher, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hoover Shampoo-Polisher.
However, one of the most important roles played by the user manual is to help in solving problems with Hoover Shampoo-Polisher. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hoover Shampoo-Polisher along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center