Instruction/ maintenance manual of the product TH8000 Honeywell
Go to page of 24
Vis io nP RO ® TH8 000 Ser i e s T ouch -s cr ee n Pr og ra mm abl e T he rm ost at ® U.S. Regi ster ed T rade mar k. US Pate nt No. 6 595 430, D50 91 51 and ot her pa tents p endi ng. Copyr ight © 20 07 Honey well I nter natio nal I nc. All righ ts re ser ved.
Insta llation Guide 2 W al lp la te in stal la tion 1. Separate wallplate from thermostat. 2. Mount wallplate as shown below . ME RCURY N OTICE If this produc t is r eplacin g a contr ol that contai ns mercur y in a sealed tube, do not place the old contro l in the trash.
Vis ionPRO TM TH80 00 Se ries 3 For 24VAC primary power , connect common side of transformer to “C” terminal. Insert suppl ied batteries for primary or backu p power . Po w e r opti ons Push excess wire back into the wall opening. Plug wall opening with non-flammable insulation.
Insta llation Guide 4 Wiring guide — conventional systems Wir in g 1H/1C System (1 transforme r ) Rc Power [1] R [R+Rc joined by jumper] W Heat relay Y Compressor contactor G Fan relay C 24V AC comm.
Vis ionPRO TM TH80 00 Se ries 5 1H/1C Heat Pump (no auxiliary heat) Rc Power [1] R [R+Rc joined by jumper] O/B Changeover valve [5] Y Compressor relay G Fan relay C 24V AC common [3] S1 Optional outdo.
Insta llation Guide 6 DONE TUE 15 6 2006 DONE TUE 6 PM 1:00 Remove tab. Align pins on back of thermostat with slots in wallplate , then push gently until thermo stat snaps into place.
Vis ionPRO TM TH80 00 Se ries 7 Insta ll er setup Setting Function Press DONE to exit & save settings. Press st to select function Press st to change setting Setup funct ions Set tings & Optio ns (fa ctor y de fault in bol d ) Shaded areas below apply only to TH8320/TH8321 .
Insta llation Guide 8 Setup funct ions Set tings & Optio ns (fa ctor y de fault in bol d ) Shaded areas below apply only to TH8320/TH8321 . 0240 First stage heat cycle rate (CPH= cycles per hour) .
Vis ionPRO TM TH80 00 Se ries 9 Setup funct ions Set tings & Optio ns (fa ctor y de fault in bol d ) 0500 Furnace lter change reminder 0 Off 1 10-day run time (about 1 month) 2 30-day run time .
Insta llation Guide 10 DONE TUE Inside 70 20 0120 DONE 1 0 TEST During installer setup, press t repeatedly until “T est” appears. T est number System status Press st to select test Press st to change status Press DONE to terminate testing. Shaded areas below apply only to TH8320/TH8321 .
Vis ionPRO TM TH80 00 Se ries 11 Auto Changeover (Setup Function 0300): When set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature. Heat and cool settings must be at least 2 de- grees apart. If function 0380 is set to On, the heat and cool settings must be at least 5 degr ees apart.
Installation Guide Honeywell International Inc. 1985 Douglas Drive North Golden V alley , MN 55422 http://yourhome.honeywell.com Automation and Control Solutions ® U.S. Registered T rademark. US Patent No. 6595430, D509151 and other patents pending. © 2007 Honeywell Inter national Inc.
Vis io nPRO ® TH80 00 Seri e T er mo st ato pr og ra ma ble co n p ant a lla ac tiva da po r t ac to Guí a d e in stal ac ión ¿ Ne ce sita ayu da ? P a ra r e c i b ir as is te nc ia co n e s te pr o d u ct o v is it e h tt p: / / y o ur ho me .h on ey we ll .
Guía d e insta lación 2 Insta lació n de la placa de monta je 1. Separe la placa de montaje del termostato. 2. Monte el termostato como se muestra a continuación. AVISO D E ME RCUR IO Si este produc to reempl aza a un contr ol que contie ne mercur io en un tubo sellad o, no arr oje el control viejo a la basura.
Vis ionPRO ® TH80 00 Se rie 3 Para la alimentación de energía primaria 24VCA. Conectar el lado común del transformador al terminal “C”. Inserte las baterías provis tas para alimentac ión de energía primari a o de resp aldo. Empuje el exceso de cable de vuelta en la abertura de la pared.
Guía d e insta lación 4 Guía para el cableado — sistemas convencionales Cab lea do Sistema 1H/1C (1 transf ormador ) Rc Alimentación de energía [1] R [R+Rc unidos por empalme] W Retransmisor de.
Vis ionPRO ® TH80 00 Se rie 5 1H/1C Bomba de calefacció n (sin calefacc ión auxiliar) Rc Alimentación de energía [1] R [R+Rc unidos por empalme] O/B Válvula de cambio [5] Y Retransmisor del comp.
Guía d e insta lación 6 DONE TUE 15 6 2006 DONE TUE 6 PM 1:00 Retire la lengüeta. Alinee las espigas de la parte de atrás del termost ato con las ranuras de la placa de montaje , luego presio ne suavemente hasta que el termostato calce en su lugar .
Vis ionPRO ® TH80 00 Se rie 7 Ajuste Función Oprima DONE para salir y guardar los ajustes. Oprima st para seleccionar la función Oprima st para cambiar los ajustes Función Ajus tes y opci ones (co.
Guía d e insta lación 8 Función Ajus tes y opci ones (con figu raci ón de fá bri ca en ne grit as ) 0240 Frecuencia del ciclo de calefacción de primera etapa (CPH= ciclos por hora) 5 Para estufa.
Vis ionPRO ® TH80 00 Se rie 9 Función Ajus tes y opci ones (con figu raci ón de fá bri ca en ne grit as ) 0500 Recordatorio de cambio del ltro de la estufa 0 Off 1 Tiem po de f unci onamien to .
Guía d e insta lación 10 Durante la configuración del instalador , oprima t repetidamente hasta que aparezca “T est” en pantalla. Número de prueba Estado del sistema Oprima st para seleccionar la prueba Oprima st para cambiar el estado Oprima DONE para terminar la prueba 1 Sistema de refrigeración 0 Compresor y ventilador apagados.
Vis ionPRO ® TH80 00 Se rie 11 Cambio automático (Funcióndeconguración0300):CuandoelsistemasejaenAuto,el termostato selecciona automáticamente calefacción o refrigeración de acuer do a la temperatura del interior .
Guía de instalación Honeywell International Inc. 1985 Douglas Drive North Golden V alley , MN 55422 http://yourhome.honeywell.com Soluciones para automatización y control ® Marca registrada de los EE. UU. Patente en EE.UU: Nº 6595430, D509151 y otras patentes pendientes.
An important point after buying a device Honeywell TH8000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Honeywell TH8000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Honeywell TH8000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Honeywell TH8000 you will learn all the available features of the product, as well as information on its operation. The information that you get Honeywell TH8000 will certainly help you make a decision on the purchase.
If you already are a holder of Honeywell TH8000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Honeywell TH8000.
However, one of the most important roles played by the user manual is to help in solving problems with Honeywell TH8000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Honeywell TH8000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
