Instruction/ maintenance manual of the product T8011R Honeywell
Go to page of 6
X-XX UL INST ALLA TION INSTRUCTIONS ®U.S. Registered Trademark Copyright © 2002 Honeywell • • All Rights Reserved T8011R Programmable Heat Pump Thermostat APPLICATION The T8011R Heat Pump Thermostat provides 24 Vac control of a two-stage heating and one-stage cooling heat pump system with manual changeover from heat to cool.
69-1436–1 2 T801 1R PROGRAMMABLE HEA T PUMP THERMOST A T 5 FEET [1.5 METERS] YES NO NO NO M11338 Fig. 1. Typical location of thermostat. Fig. 2. Mounting wallplate to wall. Wiring IMPORTANT Use 18-gauge maximum wire for wiring the T8011R Thermostat.
69-1436–1 3 T801 1R PROGRAMMABLE HEA T PUMP THERMOST A T Fig. 4. Restrict wiring to shaded area. Fig. 5. T8011R two stage heat, one stage cool wiring diagram with manual changeover. KEEP WIRING IN SHADED AREA MOUNTING SCREW HOLE MOUNTING SCREW HOLE WIRING ENTRANCE HOLE M11331A G C R Y W1 L W2 E B O 1 NOT ALL MODELS HAVE BOTH O AND B TERMINALS.
69-1436–1 4 T801 1R PROGRAMMABLE HEA T PUMP THERMOST A T Mounting Thermostat To Wallplate 1. Slide SYSTEM switch to the Off position. 2. Engage the tabs at the top of the thermostat and wallplate. 3. Swing down the thermostat and press the lower edge of the thermostat onto the wallplate to latch.
69-1436–1 5 T801 1R PROGRAMMABLE HEA T PUMP THERMOST A T 3. Setting Heat Cycle Rate (see Table 2 for cycle rate options and equipment). a. Press the ▲ key to display the current heat cycle rate setting of 3, 4, 5, 6, 9 or 12 cph. b. If the desired cycle rate is displayed, press the ▲ key to exit the installer setup.
69-1436–1 6 T801 1R PROGRAMMABLE HEA T PUMP THERMOST A T Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Scarborough, Ontario M1V 4Z9 69-1436–1 G.H. Rev . 2-02 Automation and Control Solutions Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 Setting Current Time and Day 1.
An important point after buying a device Honeywell T8011R (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Honeywell T8011R yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Honeywell T8011R - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Honeywell T8011R you will learn all the available features of the product, as well as information on its operation. The information that you get Honeywell T8011R will certainly help you make a decision on the purchase.
If you already are a holder of Honeywell T8011R, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Honeywell T8011R.
However, one of the most important roles played by the user manual is to help in solving problems with Honeywell T8011R. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Honeywell T8011R along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
