Instruction/ maintenance manual of the product IPGSM-DP Honeywell
Go to page of 16
I I P P G G S S M M - - D D P P C C o o m m m m e e r r c c i i a a l l F F i i r r e e C C o o m m m m u u n n i i c c a a t t o o r r I I n n s s t t a a l l l l a a t t i i o o n n a a n n d d S S e e t t u u p p G G u u i i d d e e IPGSM-DP Commercial Fire Comm unicator RADIO TROUBLE LO W BA TT AC ON AC LOSS 800-08074 1/11 Rev.
Contents General Info rmation ............................................................................................................ ...........1 Package Contents ..................................................................................
IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 1 – General Information The IPGSM-DP Commercial Fire Comm unicator (henceforth referred to as IPGSM-DP) includes everythin.
IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 2 – STEP 1 – Activate the SIM and Setup the Customer Account The communicator requires a subscriber account (customer account) to be setup with Alar mNet Direct. This is accomplished by registering th e communicator' s iGSM communications m odule with AlarmNet.
IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 3 – STEP 3 – Determine the Signal Strength and Select a Location IMPORTANT - Do Not mount this de vice outdoors.
IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 4 – 3. Install the two plastic m ounting rails for th e LED Display board. Th ey simply snap into the back plate holes. 4. Connect the LED Dis play board to its connect or, then slide the board int o the mounting rails.
IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 5 – IPGSM-DP-001-V2[US Only] TB 1 6 7 8 5 10 11 9 2 3 4 1 FOR EXTERNAL ANTENNA 50 OHM MMCX ONLY PRIMARY POWER: 9 - 16.5 VAC CURRENT: 900mA PEAK, 70mA STANDBY BATTERY: 8V. 3.
IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 6 – STEP 5 – Program the Communications Module You must use the 7720P Programming tool to program the IPGSM-DP. When using the 7720P P rogramming tool, the valu es given below are for mo st installations.
IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 7 – To exit the progr amming mode, press [ N] in response to the "Review?" pr ompt. Then press [Y] to the "Exit Prog Mode?" prompt. Upon exiting, the ro ot file is updated to log the changes made.
IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 8 – IPGSM-DP Trouble Detection Information Telco 1 is used for th e Fire Panel to output con tact ID messages to the IPGSM-DP, an d Telco 2 is use d by the IPGSM-DP to report f aults to the Fire P anel.
IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 9 – Note: If a wire pulled out of the LED Board Connector refer to the diagram on right and reinsert wir e, ensuring the connector pin is locked in. PowerBoost1 Module Information LED Indicator STATUS AC (green) AC power available.
IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 10 – iGSM Communications Module Information TB 1 6 7 8 5 10 11 9 2 3 4 1 PRIMARY POWER: 9 - 16.
IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 11 – RF Specifications Band Transmission Frequency (MHz) Transmit Power (dBm) Receive Frequency (MHz) Receive Sensitivity .
IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 12 – NOTES.
Wiring Diagram The wiring diagram below is depict ed for point-to-point electrical con nection checks used for tr oubleshootin g or componen t replacement. It is not in tended to show the phys ical routing of wires. When replacing a wire or componen t, ensure the wire is route d in the same manner as the orig inal factory wire.
FCC STATEMENT Note: This equipment has been tested and foun d to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits ar e designed to prov ide reasonable prot ection against harmful interference when the equipment is operated in a commerci al environment.
An important point after buying a device Honeywell IPGSM-DP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Honeywell IPGSM-DP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Honeywell IPGSM-DP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Honeywell IPGSM-DP you will learn all the available features of the product, as well as information on its operation. The information that you get Honeywell IPGSM-DP will certainly help you make a decision on the purchase.
If you already are a holder of Honeywell IPGSM-DP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Honeywell IPGSM-DP.
However, one of the most important roles played by the user manual is to help in solving problems with Honeywell IPGSM-DP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Honeywell IPGSM-DP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
