Instruction/ maintenance manual of the product 7580g Honeywell
Go to page of 202
Genesis 7580g Presentation Area Imager User’s Guide.
Disclaimer Honeywell Interna tional Inc. (“HII”) reser ves the right to make changes in sp ecifications and ot her informatio n contained in th is document without pr ior noti ce, and the reader should in all case s consult HII to deter mine whether any such chang es hav e been made.
Pr oduct Agency Compliance USA FCC P ar t 15 Subpar t B Class B This device complies with part 15 of the FCC Rules. Operation is subject to the follo wing two conditions: 1. This device may not cause harmful interfer ence. 2. This device must accept any interference received, includin g interference that may cause undesired operation.
Eur ope The CE marking indicate s compliance to 2004/108/EC EM C Directi ve with Standards EN55022 CLASS B, EN55024, EN61000-3-2, EN61000-3-3 and 2011/65/EU RoHS directive. In addition, complies to 2006/95/EC Low V oltage Direc- tive , when shipped with recommended power supply .
Required Safety Labels Compliance Label location Part Number, Serial Number and Revision Information location Illumination output.
.
i Chapter 1 - Ge tting Started About This Manual ................................................. ............................................................. .1- 1 Unpacking Your Device .................... .........................................
ii RS232 Modifiers .................................................... ............................................................ 2-18 RS232 Baud Rate ............................................ ....................................................
iii Enhanced Object Detection ................................................................... ............................ 3-12 Centering ............................... .......................................................................... ..
iv Chapter 6 - Symbologies All Symbologies .......................................... ................................................................ ...... ... 6-1 Message Length Description ................................. ........................
v Data Matrix ............................................................ ........................................................ .... 6-40 Data Matrix Code Page ........................................................ ..............................
vi EZConfig-Scanning Introduction................................................................................. ....... 10-3 Installing EZConfig-Scanning fr om the Web ......................................................... ....... 10-3 Resetting the Factory Defaults .
vii Appendix A - Reference Charts Symbology Charts ...................................................................... ......................................... A-1 Linear Symbologies ................................................................
viii.
1 - 1 1 Getting Star ted About This Manual This User’ s Guide provides installation and programming inst ruction s f or the Genesi s 7580g area-imaging scanners. Product specifications, dimensions, warr anty , and cust omer suppor t informa tion are also included.
1 - 2 2. Connect the appropriate interface cable to the device and to the terminal/computer. Note: The power supply must be ordered separate ly, if needed. 3. Turn the terminal/computer power back on. The scanner beeps. 4. Verify the scanner operation by sca nning a bar code from the Sample Symbols in th e back of this manual.
1 - 3 Connecting with RS485 A Genesis scanner can be connected for an IBM POS terminal interface. 1. Connect the appropriate interface cable to the device, then to the computer. 2. Turn the terminal/computer power back on. The scanner beeps. 3. Verify the scanner operation by sca nning a bar code from the Sample Symbols in th e back of this manual.
1 - 4 USB Interface with EAS 1. Connect the appropriate in terface and EAS ca ble to the device, and then to the comp uter. 2. The scanner beeps. 3. Verify the scanner o peration by scanning a b ar code from the Sample Symbols in the back of this m anual.
1 - 5 RS232 Interface with EAS 1. Turn off power to the termina l/computer. 2. Connect the appropriate in terface and EAS cable to the device, and then to the comp uter. Note: For the scanner to work properly, you must have the correct cable for your type of terminal/computer.
1 - 6 Setting Custom Defaults Y ou ha ve the ability to create a set of menu commands as your own, custom def aults. T o do so , scan the Set Custom De faults bar code below before scanning the menu commands f or your cu stom def aults.
2 - 1 2 Pr ogramming the Interface Intr oduction This chapter describes how to progr am your system f or the desired interf ace. Pr ogramming the Interface - Plug and Play Plug and Play bar codes pro vide instant scanner set up for commonly used interf aces.
2 - 2 RS485 Scan one of the following “Plug and Play” codes to program the scanner f or an IBM POS ter minal interface. Note: After scanning one of these codes, you must power cycle the cash register .
2 - 3 RS485 P acket Length If you are using P ac ket mode, y ou can specify the size of the data “pack et” that is s ent to the host. Scan the Pa c k e t Length bar code, then the packet siz e (from 20 - 256) from the Programming Chart inside the back cov er of this man- ual, then Save .
2 - 4 USB HID Scan the follo wing code to program the scanner f or USB HID bar code scanners. USB Serial Scan the f ollo wing code to prog ram the scann er to emulat e a re gular RS232-based COM Po r t. If you are using a Microsoft® Windows® PC , you will need to download a driver from the Hone ywell website (www.
2 - 5 V erifone ® Rub y T erminal Default Settings Scan the following Plug and Pla y code to program the scanner for a V er ifone Ruby terminal. This bar code sets the baud rate to 1200 bps and the data format to 8 data bi ts, no parity bit, 1 stop bit.
2 - 6 Datalogic™ Magellan ® A ux P o r t Configuration Scan the follo wing Plug and Play code to program the scanner for a Datalogic Magellan auxiliar y por t configuration . This bar code sets the baud rate to 9600 bps and the data fo rm at to 8 data bits, no pari ty , 1 stop bit.
2 - 7 Ke yboar d Country Lay out Scan the appro priate countr y code below to program the ke yboard lay out for y our countr y or language. As a general rule, the f ollowing characters are suppor ted,.
2 - 8 Ke yboar d Countries (Continued) Bulgaria (Cyrillic) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ).
2 - 9 Ke yboar d Countries (Continued) Dutch (Netherlands) Estonia Faroese Finland France Gaelic Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin).
2 - 10 Ke yboar d Countries (Continued) Greek (319) Greek (Latin) Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Italian (142) Italy.
2 - 11 Ke yboar d Countries (Continued) Japan ASCII Kazakh Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Mongolian (Cyrillic).
2 - 12 Ke yboar d Countries (Continued) Norway Poland Polish (214) Polish (Programmers) Portugal Romani a Russia Russian (MS) Russian (Typewriter) SCS Serbia (Cyrillic).
2 - 13 Ke yboar d Countries (Continued) Serbia (Latin) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) Switzerland (German) Tatar.
2 - 14 Ke yboar d Style This programs ke yboard styles, such as Cap s Lock and Shift Lock. If you hav e used Keyboard Co nversion settin gs, they will ov erride any of the follo wing K eyboard Style settings. Def ault = Regular. Regular is used when you normally have the Caps Loc k ke y off.
2 - 15 Caps Lock is used when you nor mally hav e the Caps Lock ke y on. Shift L ock is used when you normally hav e the Shift Lock k ey on (not common to U .S . ke yboards). A utomatic Caps Lock is used if you change the Caps Lock k ey on and off. The software tr acks and reflects if you ha ve Caps Lock on or off .
2 - 16 Contr ol Character Output This selection sends a text string instead of a control character . For e xample, when the control character f or a carr iage retu rn i s e xpected, the ou tput would display [CR] instead of the ASCII code o f 0D . Refer to ASCII Conversion Chart (Code Page 1252) on page A-3.
2 - 17 Tu r b o M o d e : The scanner sends characters to a ter minal faster . If the ter minal drops characters, do not use T urbo Mode. Def ault = Off. Numeric Keypad Mode: Sends numeric characters as if entered from a numeric ke ypad. Default = Off .
2 - 18 RS232 Modifiers RS232 Baud Rate Baud Rate sends the da ta from the scanner to the ter minal at the specified rate. The host ter minal must be set for the same baud rate as the scanner .
2 - 19 RS232 W ord Length: Data Bits, Stop Bits, and P arity Data Bits sets the word length at 7 or 8 bits of data per characte r . If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits.
2 - 20 RS232 Receiver Time-Out The unit stays aw ake to receive data until the RS232 Receiver Time -Out expires. A manual or serial tr igger resets the time- out. When an RS232 receiver is sleeping, a character may be s ent to wak e up the receiver and reset the time-out.
2 - 21 XON/XOFF Standard ASCII control characters can be used to tell the sca nner to star t sen ding data ( XON/XOFF On ) or to stop sending data ( XON/XOFF Off ). When the host sends the XOFF character (DC3, he x 13) to the scanner , data transmission stops.
2 - 22 Scanner -Bioptic A CK/NAK Mode Bioptic A CK/Nak On must be scanned so the scanner w ill wait for an A CK or NAK from a bioptic scanner after each packet is sent. The Scanner-Bioptic ACK/NAK Timeout (below) controls how long the scanner will w ait for a response.
3 - 1 3 Input/Output Settings P o wer Up Beeper The scanner can be programmed to beep when it’ s powered up . Scan the Off bar code(s) if you don’t want a pow er up beep. Default = P ower Up Beeper On. Beep on BEL Character Y ou ma y wish to f orce the scanner to beep upon a command sen t from the host.
3 - 2 Good Read and Error Indicator s Beeper – Good Read The beeper may be programmed On or Off in response to a good read. T ur ning this option off only turn s off the beeper response to a good read indication . All error and menu beeps are still audible.
3 - 3 Beeper Pitch – Err or The beeper pitch cod es modify the pitch (frequency) of the s ound the scanner emits when there is a bad read or error . Def ault = Razz. Beeper Duration – Good Read The beeper duration codes modify the length of the beep the scanner emits on a good read.
3 - 4 Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1 - 9. The same n umber of beeps will be applied to the beeper and LED in response to a good read. For e xample, if y ou program this option to hav e five beeps , there will be five beeps and five LED flashes in response to a good read.
3 - 5 Manual T rig ger Modes When in manual trigger mode, the scanner scans until a bar code is read, or until the trigger is released. T wo modes are avail - able , Normal and Enhanced . N orma l mode offers good scan speed and the longe st working rang es (depth of field).
3 - 6 Read Time-Out Use this selection to set a time-out (in millisecond s) of the scanner’ s trigger whe n using serial commands to tr igger the scanner . Once the scanne r has timed out, you can activate the sc anner either by pressing the trigger or using a ser ial tr ig- ger command.
3 - 7 Presentation LED Beha vior after Decode When a scanner is in presentation mode, the LEDs dim 30 seconds after a bar code is decoded. If yo u wish to dim the LEDs immediately after a bar code is decoded, scan th e LEDs Off bar code, below . Default = LEDs On.
3 - 8 In the e xample below , the white bo x is the center ing window . The centering window has been set to 20% left, 30 % right, 8% top , and 25% bottom. Since Bar Code 1 passes through the center ing window , it will be read. Bar Code 2 does not pass through the center ing window , so it will not be read.
3 - 9 CodeGate ® When CodeGate is On , the trigger is used to allow decode d data to be transmitt ed to the host system. The scanner remains on, scanning and decoding bar codes, but the bar code data is not transmitted until the tr igger is pressed .
3 - 10 Mobile Phone Read Mode When this mode is selected, your scanner is optimiz ed to read ba r cod es from mobile phon e or other LED d isplays . Howe ver , the speed of scanning pr inted bar codes may be slightly lower wh en this mode is enabled.
3 - 11 User -Specified Reread Delay If you w ant to set your o wn length for the reread dela y , scan the bar code below , the n set the delay (from 0-30,000 millisecond s) by scanning digits from the inside back co ver , then scanning Sa ve .
3 - 12 User-Specified Aimer Dela y If you want to set y our own length for the duration of the del ay , scan the bar code below , then set the time-out b y scanning digits (0 - 4,000 ms) from the Programming Chart inside the back cov er of this manual, then scan Save .
3 - 13 Centering Use Centering to narrow the scanner’ s field of view to mak e sure that when the scanner is hand -held , it reads only those bar codes intended by the user . F or instance, if m ultiple codes are p laced closely together, centering will insu re that only the desired codes are read.
3 - 14 Preferred Symbology The scanner can be programmed to specify one symbology as a hig her pri ority over other symbologies in situations where both bar code symbologies appear on the same label, but the lower priority symbology cannot be disabled.
3 - 15 High Priority Symbology T o specify the high pr iority symbolo gy , scan the High Priori ty Symbology bar code below . On the Symbology Charts on page A-1, find the symbology you want to set as high pr iori ty . Locate the Hex v alue for that symbology and scan the 2 digi t hex value from the Progr amming Char t (insid e back co ver).
3 - 16 Output Sequence Editor This programming selection all ows you to program the scanner to output data (when scanning more than one symb ol) in whatev er order y our applicatio n requires, regardless of t he order in which the bar codes are scan ned.
3 - 17 41 star t character match for Code 39, 41h = “A” FF ter mination string for first code 6A code identifier f or Code 128 9999 code length that must match for Code 128, 9999 = all lengths 42 .
3 - 18 Scan Discard P art ial Sequence to discard par tial sequences when the outp ut sequence operation is ter minated before completion. Scan T ransmit Partial Sequence to transmit par tial sequences. (Any fields in the sequence where no data match occurred w ill be skipped in the output.
3 - 19 No Read With No Read turned On , the scanner notifies you if a code cannot be read . If using an EZConfig-Scanning T ool Scan Data Window (see page 10-3 ), an “NR” appears when a code can not be read. If No Read is tur ned Off , the “NR” will not appear .
3 - 20 W orking Orientation Some bar codes are directi on-sensitive. For e xample, KI X codes and OCR can misre ad when scanne d sidew ays or upside down. Use the working orientation settings if your direction-se nsitive codes will not usuall y be presented upr ight to the scan ner.
4 - 1 4 Data Editing Prefix/Suffix Overview When a bar code is scann ed, additional information is sen t to the host compute r along with the b ar code data. This group of ba r code data and additional, user-defined data is call ed a “message str i ng.
4 - 2 Example: Add a T ab Suffix to All Symbologies Step 1. Scan Add Suffix . Step 2. Scan 9 , 9 from the Programming Chart inside the back cover of this manual to apply th is suffix to all symbologies. Step 3. Scan 0 , 9 from the Programming Chart inside the back cover of this manual.
4 - 3 Function Code T ransmit When this selection is enabled and function codes are contai ned within the scanned data, the sca nner transmits the functi on code to the te rmin al. Char ts of the se function codes are provided in Supported Interface Ke ys star ting on page 9-2 .
4 - 4 Ne xt, scan the Character to T rigger Delay bar code, then the 2-digit hex v alue for the ASCII character that will trigger the delay ASCII Conversion Chart (Code Page 1252), beginning on page A-3. T o remov e this dela y , scan the Dela y Length bar code, and set the number of delays to 0.
5 - 1 5 Data Formatting Data Format Editor Intr oduction Y ou ma y use the Data Format Editor to change the scanne r’ s output. For e xample, y ou can use the Data Format Editor to inser t characters at cer tain points in bar code data as it is scanne d.
5 - 2 Step 5. Lengt h Specify what length (up to 9999 characters) of data will be a cceptable for this symbolog y. Scan the four digit data l ength from the Programming Chart inside the back cover of this manual. For ex ample, 50 characte rs is entered as 0050.
5 - 3 Data Format Editor Commands When working with th e Data F or mat Editor , a vir tual cursor is moved along your input data stri ng. The follo wing commands are used to both mov e this cursor to different positions, and to sele ct, replace, and inser t data into the final outpu t.
5 - 4 0D is the he x value f or a CR F1 is the “Send all characters” command 0D is the he x value f or a CR The data is ou tput as: 1234567890 ABCDEFGHIJ <CR> Send all chara cters up to a pa.
5 - 5 Insert a character multiple times F4 Send “xx” character “nn” times in the output message, leaving the cursor in the current positi on. Syntax = F4xxnn wher e xx stands for the insert character’s hex value for its ASCII code, and nn is the numeric value (00-99) for the number of times it should be sent.
5 - 6 Insert bar code length B4 Insert the bar code’s length in the output message, without moving the cursor. The leng th is expressed as a numeric string and does n ot include leading zeroes. B3 and B4 Example: Insert the symbology name and length Send the symbology name and length before the bar code data from the b ar code above .
5 - 7 F5 Example: Move the cur s or forwar d and send the data Mov e the cu rsor forward 3 characters, then send the rest of the bar code data from the bar code above .
5 - 8 Command string: F84 4F10D F8 is the “Search f orward f or a character” command 44 is the hex v alue for “D” F1 is the “Send all characters” command 0D is the he x value f or a CR The.
5 - 9 This example shows a bar code that has been zero filled. Y ou may w ant to ignore the zeroes and send all the data that f ollows. E6 searches forw ard for the first character that is not zero , then sends all th e data after , follow ed by a carriage retur n.
5 - 10 If the bar code has characters that the host application do es not want included, you can use the E4 comman d to replace those characters with something else. In this example, you will replace the zeroes in the bar cod e abov e with carriage retur ns.
5 - 11 If you will only accept data from bar codes that begin with a letter , you can use ED to check f or the number . Command string: ED F10D ED is the “Check f or a non-numeric character” command F1 is the “Send all characters” command 0D is the he x value f or a CR If this bar code is read, the f or mat fa ils.
5 - 12 Choose one of the following options. Def ault = Data Formatter On, Not Requi red, K eep Prefix/Suffix. Data Format Non- Match Err or T one When a bar code is encountered that doesn’ t match your required data f or mat, the scanner nor mally generates an error tone.
5 - 13 Single Scan Data Format Change Y ou can also switch between data f or mats for a single scan. The next bar code is scanned using an alter nate data format, then re ver ts to the format you ha ve select ed abov e (either Primar y , 1, 2, or 3). F or example , you may ha ve set y our device to the data format you sa ved as Data Format 3.
5 - 14.
6 - 1 6 Symbologies This programming section contains the f ollowing menu selections. Ref er to Chapter 11 f or settings and defaults . All Symbologies If you want to decode all the symbologies al lowab le for y our scanner , scan the All Symbologies On code.
6 - 2 EXAMPLE: Decode only those bar codes wi th a count of 15 characters. Min. length = 15Max. length = 15 F or a value other than the minimum and maximum message length def aults, scan the bar codes.
6 - 3 Codabar Concatenation Codabar suppor ts symbol concatenation. Whe n you enab le c oncaten ation, the scanner look s for a Codabar symbol having a “D” star t character , adjacent to a symbol having a “D” stop character . In this case the two messages are concatenated into one with the “D” characters omitted.
6 - 4 Code 39 < Default All Code 39 Settings > Code 39 On/Off Code 39 Star t / Stop Characters Star t/Stop characters identify the leading and trailing ends of the bar code. Y ou ma y either transmit, or not transmit Star t/ Stop characters. Def ault = Don’t T ransmit.
6 - 5 Code 39 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation.
6 - 6 Full ASCII If Full ASCII Code 39 decoding is enabled, cer tain characte r pairs within the bar code symbol will be inter preted as a single character . For e xample: $V will be decoded as the ASCII ch aracter SYN, and /C will b e decoded as the ASCII character #.
6 - 7 Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off Check Digit No Check Digit indicates that the scanner rea ds and transmits bar code da ta with or without a check digit.
6 - 8 NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off Check Digit No Check Digit indicates that the scanner rea ds and transmits bar code da ta with or without a check digit.
6 - 9 NEC 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation.
6 - 10 Code 93 Append This function allows the scanner to append the data from sev eral Code 93 bar codes tog ether before transmitting them to the host computer .
6 - 11 Straight 2 of 5 Industri al (three-bar star t/stop) <Default All Straight 2 of 5 Industrial Settings> Straight 2 of 5 Industrial On/Off Straight 2 of 5 Industrial Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation.
6 - 12 Straight 2 of 5 IA T A (tw o-bar start/stop) <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IA T A On/Off Straight 2 of 5 IA T A Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation.
6 - 13 Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Matrix 2 of 5 On/Off Matrix 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation. Minimum and Maximum lengths = 1-80.
6 - 14 Code 11 <Default All Code 11 Settings> Code 11 On/Off Check Digits Required This option sets whether 1 or 2 ch eck digi ts are required with Code 11 bar codes. Def ault = T wo Check Digits. Code 11 Message Length Scan the bar codes below to change the message length.
6 - 15 Code 128 <Default All Code 128 Settings> Code 128 On/Off ISBT 128 Concatenation In 1994 the Inter national So ciety of Blood T ransfusion (ISBT) ratified a standard fo r communicating cr itical blood informa- tion in a uniform manner . The use of ISBT f or mats requir es a paid license.
6 - 16 Code 128 Append This function allows the scanner to append the data fro m se vera l Code 128 bar codes together before transmitting them to the host computer .
6 - 17 GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off GS1-128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation. Minimum and Maximum lengths = 1-80.
6 - 18 Te l e p e n <Default All Telepen Settings> T elepen On/Off T elepen Output Using AIM T elepen Output, the scanne r read s symbols with star t/stop pattern 1 and decodes them as standard full ASCII (star t/stop patter n 1).
6 - 19 UPC-A <Default All UPC-A Settings> UPC-A On/Off Note: To convert UPC-A bar codes to EAN-13, see Convert UPC-A to EAN-13 on page 6-24. UPC-A Check Digit This selection all ows you to specify whether the check digit sh ould be transmitted at the end of the scan ned data or not.
6 - 20 UPC-A Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-A data. Def ault = Off for both 2 Digit and 5 Digit Addenda. UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar code s that hav e addenda.
6 - 21 UPC-A/EAN-13 with Ex tended Coupon Code Use the follo wing codes to e nable or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the default setting ( Off ), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes.
6 - 22 UPC-E0 <Default All UPC-E Settings> UPC-E0 On/Off Most U. P .C. bar codes lead with the 0 number system. T o read these code s, use the UPC-E0 On selection. If y ou need to read codes that lead with the 1 n umber system, use UPC-E1 (page 6-24).
6 - 23 UPC-E0 Addenda Separator When this feature is On , there is a space between the dat a from the bar code and the data from the addenda. When turned Off , there is no space. Default = On. UPC-E0 Check Digit Check Digit specifies whether the check digit should be transmitted at the end of the scanned data or not.
6 - 24 UPC-E1 Most U .P .C. bar codes lead with the 0 number system . For these codes, use UPC-E0 (page 6-22). If you need to read codes that lead with the 1 number system, use the UPC-E1 On selection.
6 - 25 EAN/JAN-13 Chec k Digit This selection all ows you to specify whether the check digit sh ould be transmitted at the end of the scan ned data or not. Def ault = On. EAN/JAN-13 Ad denda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data.
6 - 26 EAN/JAN-13 Ad denda Separator When this feature is On , there is a space between the dat a from the bar code and the data from the addenda. When turned Off , there is no space. Default = On. Note: If you want to enable or disable EAN 13 with Extended Coupon Code, refer to UPC-A/EAN -13 with Extended Coupon Code (page 6-21).
6 - 27 EAN/J AN-8 <Default All EAN/JAN-8 Settings> EAN/JAN-8 On/Off EAN/JAN-8 Chec k Digit This selection all ows you to specify whether the check digit sh ould be transmitted at the end of the scan ned data or not. Def ault = On. EAN/JAN-8 Ad denda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data.
6 - 28 EAN/JAN-8 Ad denda Required When Required is scanned, the sca nner will only read EAN /JAN-8 bar codes that hav e addenda. Def ault = No t Required. EAN/JAN-8 Ad denda Separator When this feature is On , there is a space between the dat a from the bar code and the data from the addenda.
6 - 29 MSI <Default All MSI Settings> MSI On/Off MSI Check Character Diff erent types of check characters are used with MSI b ar codes. Y ou can program the scanner to read MSI bar codes with T ype 10 check char acters. Default = V alidate T ype 10, but Don’t T ransmit.
6 - 30 MSI Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation.
6 - 31 GS1 DataBar Omnidirectional < Default All GS1 DataBar Omnidirectional Settings > GS1 DataBar Omnidi rectional On/Off GS1 DataBar Limited < Default All GS1 Data Bar Limited Settings >.
6 - 32 GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settin gs > GS1 DataBar Expanded On/Off GS1 DataBar Expanded Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation.
6 - 33 Codabloc k A <Default All Codablock A Settings> Codabloc k A On/Off Codabloc k A Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation. Minimum and Maximum lengths = 1-600 .
6 - 34 Codabloc k F <Default All Codablock F Settings> Codabloc k F On/Off Codabloc k F Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation. Minimum and Maximum len gths = 1-2048.
6 - 35 PDF417 < Default All PDF417 Settings > PDF417 On/Off PDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation. Minimum and Maximum len gths = 1-2750.
6 - 36 Micr oPDF417 < Default All MicroPDF417 Settings > MicroPDF417 On/Off MicroPDF417 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation. Minimum and Maximum lengths = 1-366 .
6 - 37 UPC/EAN V ersion Scan the UPC/EAN V ersion On bar code to decode GS1 Composi te symbols that hav e a U.P . C . or an EAN linear compo- nent. (This does not aff ect GS1 Composite symbol s with a GS1-128 o r GS1 linear co mponent.) Default = UPC/EAN V e r- sion Off.
6 - 38 TCIF Linked Code 39 (TLC39) This code is a composite code since it has a Code 39 lin ear component and a MicroPDF417 stacked code component. All bar code readers are capable of reading the Code 39 linea r comp onent. The MicroPDF417 compo nent can only be decod ed if TLC39 On is selected.
6 - 39 QR Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation.
6 - 40 Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off Data Matrix Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation. Minimum and Maximum len gths = 1-3116.
6 - 41 codes were created (see ISO 2022/ISO 646 Character Replacements on pa ge A-7), and scan the value and the Save bar code from the Programming Chart on the inside the back cov er of this manual.
6 - 42 Aztec Code < Default All Aztec Code Settings > Aztec Code On/Off Aztec Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional inf or mation. Minimum and Maximum len gths = 1-3832.
6 - 43 codes were created (see ISO 2022/ISO 646 Character Replacements on pa ge A-7), and scan the value and the Save bar code from the Programming Chart on the inside the back cov er of this manual.
6 - 44 P ostal Codes - 2D The f ollowing lists the possible 2D postal codes, and 2D postal co de combinations that are allowed. Only one 2D postal code selection can be active at a time. If y ou scan a se cond 2D po stal code selection, the first selection is overwritten.
6 - 45 Combination 2D P ostal Codes: Postnet On Also see Postnet Check Digit , page 6-47. Postnet with B and B ’ Fields On InfoMail On InfoMail and British Post On Intelligent Mail Bar Code an d Pos.
6 - 46 Planet Code and Postnet with B and B’ Field s On Planet Code and Postal-4i On Planet Code and Intelligent Mail Bar Code On Planet Code, Postnet, and Postal-4i On Planet Code, Postnet, and Int.
6 - 47 Planet Code Check Digit This selection allows you to specify whether the check digit shoul d be transmitted at the e nd of Planet Code d ata. Default = Don’t T ransmit. P ostnet Chec k Digit This selectio n allows y ou to specif y whether the check digit should be transmitted at the end of Postnet data.
6 - 48 Combination C and N T ables causes the field to be interpreted using ei ther the C or N T ables. P ostal Codes - Linear The f ollowing lists linear postal codes.
6 - 49 K orea P ost <Default All Korea Post Settings> K orea P ost K orea P ost Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) f or addi- tional information. Minimum and Maximum lengths = 2-80.
6 - 50.
7 - 1 7 EAS Settings EAS Considerations Do not install any la rge iron fixtures , such as steel su pport poles, near the Genesis 7580g. Doing so may re-shape the EAS tag deactivation field. EAS Deactiv ation The Genesis 7580g suppor ts deactiv ation of Checkpoint EAS tags.
7 - 2 Checkpoint EAS Controller Settings The f ollowing switch settings f or a Checkpoint Counter p oint IX controller can be used as a star ting point, howe ver , th ese settings should be tuned according to your par ticular insta llation. EAS Contr oller Scan one of the follo wing bar codes to tur n EAS On or Off .
7 - 3 EAS Interlocked Duration Timeout When using the Interlocked EAS Mode of Operation, you mu st set the lag time between when a bar code is read and when the EAS tag is deactiv ated.
7 - 4.
8 - 1 8 Imaging Commands The scanner is like a digita l camera in the way it captures, manipulates, and transf ers images. The f ollowing commands allow you to alter the w a y the scanner performs these functions. Note: You must set the scanner a Manual Trigger Modes (pag e 3-5) in order to take images.
8 - 2 0B No beep (default) 1B Sounds a beep when the image is captured. T - W ait for T rigger W aits fo r a hardware button push bef ore taking the image.
8 - 3 W - T arget White V alue Sets the target f or the median gr ayscale v alue in the captured image. F or capturin g close-up images of high contrast doc- uments, a lo wer setting, such as 75, is recommended. Higher se ttings result in long er exposure times and brighter images, but if the setting is to o high, the image may be overe xposed.
8 - 4 IMGSHP Modifiers A - Infinity Filter Enhances pictures taken from v er y long distances (greater than 10 feet or 3m). The Infinity Filter should not be used wi th IMGSNP Modifiers (page 8-1). 0A Infinity filter off (default) 1A Infinity filter on C - Compensation Flattens the image to account f or variations in illumination across the image.
8 - 5 E - Edge Sharpen An edge shar pen filter cleans up the edges of an image, making it look cleane r and shar per . While edge shar penin g does make the image look cleane r , it also remov es some fine deta il from the origina l image. T he strength of the edge sharpen filter can be entered from 1 to 24.
8 - 6 1iy Invert around the Y axis (flips picture left to right) IF- Noise Reduction Used to reduce the salt and pepper noise in an image. 0if No salt and pepper noise reduction (default) 1if Salt and.
8 - 7 IR - Image Rotate 0ir Image as snapped (rightside up) (defa ult) 1ir Rotate image 90 degrees to the right 2ir Rotate image 180 degrees (upside down) 3ir Rotate image 90 degrees to the left J - JPEG Image Quality Sets the desired quality when the JPEG imag e format is se lected.
8 - 8 n L The left edge of the shipped image corresponds to column n of the image i n memory. Range: 000 - 843. (Default = 0) n R The right edge of th e shipped image corresponds to column n - 1 of the image in memory. Range: 000 - 843. (Default = all columns) n T The top edge of the shipped i mage corresponds to row n o f the image in memo ry.
8 - 9 3S ship every 3rd pixel, both horizontally and verticall y U - Document Image Filter Allows y ou to input parameters to shar pen the edges an d smooth the area between the edges of te xt in an image.
8 - 10 1W Ship histogram Image Size Compatibility If you ha ve applications that e xpect an image ship to retu rn e xactly 640x480 pixels, scan the Force V GA Resolution bar code.
8 - 11 Below is an e xample of a signature captu re application. In this example, the aimer is centered over the signature ca pture area and the trigge r is pressed. A single beep is emitted, indicati ng that the scann er has read a Code 128 bar code and the data ha s been transferred to the host.
8 - 12 B - Output Ima ge Height This option is used to size the image verticall y . If using this option, set the resolution (R) to zero . D - Pixel Depth This indicates the number of bits per pixel in the transmitted image , which defines whether it will be gra yscale or black and white.
8 - 13 n K Apply gamma correction factor n ( n = 1-255) R - Resolution of Signature Captur e Area The resolution is the number of pix els that the scanner out puts per each minimum bar width. The higher the value f or R, the higher the q uality of the image, but also the larger the file size.
8 - 14 X - Horizontal Bar Code Offset The horiz ontal bar c ode offset allows y ou to offset the ho rizontal center of the signat ure capture area. P ositive v alues move the horizontal center to the r ight and negative v alues to the left . Measurements are in multiples of the minimum bar width.
9 - 1 9 Interface K eys Ke yboar d Function Relationships The f ollowing K eyboard Function Code, He x/ASCII V alue, and Full ASCII “CTRL ”+ relationships ap ply to all ter minals that can be used with the scanner. Ref er to page 2-16 enable Control + X (Control + ASCII) Mode.
9 - 2 Suppor ted Interface Ke ys Denmark 8 9 6 - Norwa y 8 9 6 - Spain [ ] 6 - ASCII HEX IBM PC/A T and Compatibles, USB PC Keyb oa rd Apple Mac/iMac Supported Ke ys NUL 00 Reser ved Reser ved SOH .
10 - 1 10 Utilities T o Add a T est Code I.D . Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D . before the decoded symbology . (See the Symbology Charts, beginning on page A-1) for the single character code that identi fies each symbology .
10 - 2 T est Menu When you scan the T est Menu On code, then scan a programming code in this manual, the scanner displays the content of a programming code. The programming function will still occur , but in addition, the conten t of that programming code is ou tput t o the ter minal.
10 - 3 EZConfig-Scanning Intr oduction EZConfig-Scanning provides a wide range of PC-based programming functions that can be performed o n a scanner connected to your PC's COM por t. EZConfig-Scanning allows you to do wnload upgrades to the scanner's firmware, change programmed parameters, and create and print programming bar codes.
10 - 4 Resetting the F actor y Defaults If you aren’t sure what programming optio n s are in your scanner , or you’ve changed some options and want to restore the scan- ner to f actor y default settings, first scan the Remove Custom Defaults bar code, then scan Activate Defaults .
11 - 1 11 Serial Pr ogramming Commands The serial programming commands can be used in pla ce of the progr amming bar code s. Both the serial commands and the programming bar codes will program the scanner. F or complete descr iptions and examples of each serial programming com- mand, refer to the corresponding programming bar code in this manual.
11 - 2 Data Field Usage When a quer y is used in place of the Data field, th e quer y applies only to the specific command identifi ed by the T ag and SubT ag field s. Concatenation of Multiple Commands Multiple commands can be issued within one Prefix/Storage s eque nce.
11 - 3 the Minimum Message Length (MIN) is set to 2 characters; the Maximum Message Length (MAX) is set to 60 characters; and the Default setting (DFT) has no v alue. T rigger Commands Y ou can activ ate and deactivate the scanner with serial trig ger commands.
11 - 4 Plug and Play Codes: USB USB K eyboard (PC) P AP124 2-3 USB K eyboard (Mac) P AP125 2-3 USB Japanese K eyboard (PC) TRMUSB134 2-3 USB HID P AP131 2-4 USB Serial TRMUSB130 2-4 CTS/RT S Emulation.
11 - 5 F rance KBDCTY3 2-9 Gaelic KBDCTY84 2-9 Germany KBDCTY4 2-9 Greek KBDCTY17 2-9 Greek (220 Latin) KBDCTY64 2-9 Greek (220) KBDCTY61 2-9 Greek (319 Latin) KBDCTY65 2-9 Greek (319) KBDCTY62 2-10 G.
11 - 6 Slov akia (QWER TZ) KBDCTY48 2-13 Slov enia KBDCTY31 2-13 Spain KBDCTY10 2-13 Spanish variation KBDCTY51 2-13 Sweden KBDCTY23 2-13 Switzerland (F rench) KBDCTY29 2-13 Switzerland (Ger man) KBDC.
11 - 7 9600 BPS 232BAD5 2-18 19200 BPS 232BAD6 2-18 38400 BPS 232BAD7 2-18 57600 BPS 232BAD8 2-18 *115200 BPS 232BAD 9 2-18 W ord Length: Data Bits, Stop Bits, and P ari ty 7 Data, 1 Stop , P ar ity E.
11 - 8 Beeper V olume - Good Read Off BEPL VL 0 3-2 Low BEPL VL1 3-2 Medium BEPL VL2 3-2 *High BEPL VL3 3-2 Beeper Pitch - Good Read (F requency) Low (1600) (min 400Hz) BEPFQ11600 3-2 *Medium (2700 Hz.
11 - 9 Right of Presentation Center ing Window (*60%) PDCRGT### 3-9 T op of Presentatio n Centering Wi ndow (*40%) PDCT OP### 3-8 Bottom of Presentation C entering Windo w (*60%) PDCBO T### 3-8 CodeGate *CodeGate Off Out-of-Stand AOSCGD0. 3-9 CodeGate On Out-of -Stand A OSCGD1.
11 - 10 Output Sequence Editor Enter Sequence SEQBLK 3-17 Def ault Sequence SEQDFT 3-17 P ar tial Sequence T ransmit P ar tial Se quence SEQTTS1 3-18 *Discard P ar tia l Sequence SEQTTS0 3-18 Require .
11 - 11 *Data Formatter On, Not Required, Keep Prefix/Suffix DFM_EN1 5-12 Data Format Required, Keep Prefix/Suffix DFM_EN2 5-12 Data Formatter On, Not Required, Drop Prefix/Suffix DFM_EN3 5-12 Data Fo.
11 - 12 Code 39 Check Char . * No Check Char . C39CK20 6-4 V alidate, But Don ’t T ransmit C39CK21 6-4 V alidate, and T ransmit C39CK22 6-4 Code 39 Message Length M inimum (0 - 48) *0 C39MIN## 6-5 M.
11 - 13 Straight 2 of 5 Industr ial Def ault All Straight 2 of 5 Industr ial Settings R25DFT 6-11 *Off R25ENA0 6-11 On R25ENA1 6-11 Straight 2 of 5 Industrial Message Length Minimum (1 - 48) *4 R25MIN.
11 - 14 T elepen Default All T el epen Settings TELDFT 6-18 *Off TELENA0 6-18 On TELENA1 6-18 T elepen Output *AIM T elepen Output TELOLD0 6-18 Origina l T elepen Outpu t TELOLD1 6-18 T elepen Message.
11 - 15 UPC-E0 Addenda 2 Digit Addenda On UPEAD21 6-23 *2 Digit Addenda Off UPEAD20 6-23 5 Digit Addenda On UPEAD51 6-24 *5 Digit Addenda Off UPEAD50 6-24 UPC-E1 *Off UPEEN10 6-24 On UPEEN11 6-24 EAN/.
11 - 16 MSI Check Character *V alidate T ype 10, but Don’t T ransmit MSICHK0 6-29 V ali date T ype 10 and T ransmit MSICHK1 6-29 V ali date 2 T ype 10 Chars, but Don’t T ransmit MSICHK2 6-29 V ali.
11 - 17 MicroPDF41 7 Def ault All Micro PDF4 17 Settings MPDDFT 6-36 On MPDENA1 6-36 *Off MPDENA0 6-36 MicroPDF417 Msg . Length Mi n imum (1-366) *1 MPDMIN### 6-36 Maximum (1-366) *366 MPDMAX### 6-36 GS1 Composite Codes On COMENA1 6-36 *Off COMENA0 6-36 UPC/EAN V ersion On COMUPC1 6-37 *Off COMUPC0 6-37 GS1 Composite Codes Msg.
11 - 18 Aztec Code Msg. Length Minimum (1-3832) *1 AZTMIN#### 6-42 Maximum (1-3832) *3832 AZTMAX#### 6-42 Aztec Append *On AZT APP1 6-42 Off AZT APP0 6-42 Aztec Code P age Aztec Code P age (*51) AZTDC.
11 - 19 Planet, Intellig ent Mail Bar Code, and P ostnet with B and B’ Fields On POST AL26 6-46 P ostal-4i, Intelligent Mail Bar Code, and P ostnet with B and B’ Fields On POST AL27 6-46 Planet, P.
11 - 20 *W ait f or T r igger Off SNPTRG0 8-2 W ait f or T r igger On SNPTRG1 8-2 *LED State - Off SNPLED0 8-2 LED State - On SNPLED1 8-2 Exposure (1-7874 microseconds) SNPEXP 8-2 *Gain - None SNPGAN1.
11 - 21 Gamma Correction On (0-1000) IMGGAM### 8-7 Image Crop - Left (0-843) *0 IMGWNL### 8-8 Image Crop - Right (0-843) *843 IMGWNR### 8-8 Image Crop - T op (0-639) *0 IMGWNT### 8-8 Image Crop - Bott.
11 - 22.
12 - 1 12 Pr oduct Specifications Genesis 7580g Scanner Pr oduct Specifications P aramete r Specification Dimensions (T ypi cal): Height 5.9 inche s (150mm) Length 3.
12 - 2 Depth of Field Char ts T ypical P erformance Guaranteed P erf ormance Focus Standard Range (SR) Symbology Near Distanc e Far Di stance 5 mil Code 39 in. 0.4 3.1 mm 10 79 7.5 mil Code 39 in. 0. 2 4.7 mm 5 119 10mil Code 39 in. 0.0 6.5 mm 0.0 165 10 mil PDF417 in.
12 - 3 Standar d Connector Pinouts Note: The following pin assign ments are not compatible with Hon e ywell legacy prod ucts. Use of a cable with improper pin assignments may lea d to damage to th e unit. Use of any cab l es not provided by the manu facturer may result i n damage not covered by your warranty.
12 - 4 USB 10 Pin Modular Plug EAS 2 Pin Plug EAS - USB 10 Pin Modular Plug EAS - Serial Output 10 Pin RJ41 Modular Plug 1 Cable shi eld 2 Cable select 3 Supply ground 4 5 6 7 +5V power 8 9 Data + 10 .
13 - 1 13 Maintenance Repairs Repairs and/or upgrades are not to be performed on this product. These ser vices are to be perf or med only by an authorized ser vice center (see Customer Support on page 14-1). Maintenance Y our de vice provides reliable and efficient op eration with a minimum of care.
13 - 2 Replacing a Genesis Interface Cable 1. Turn the power to the host system OFF. 2. Disconnect the scanner’s cable from the terminal or computer. 3. Locate the small hole on the unde r side of the scanner. This is the cable release. 4. Straighten one end of a paper clip.
13 - 3 • The scanner may not be p rogrammed to output your bar code data pr operly. For example, you scan “12345” and the host displays “A12345B.” Reprogram the scanner with the proper symbology selections. See Chapter 6 . The scanner won’t read y o ur bar code at all.
13 - 4.
14 - 1 14 Customer Suppor t T echnical Assistance If you need assistance insta lling or troubleshooting your de vice, please contact us b y using one of the methods below: Knowledge Base: www.hsmknowledge base.com Our Knowledge Base provides thousands of immediate solutions.
14 - 2 EVEN WHEN HII MA Y HA VE BEEN AD VISED OF THE POSSIBILI TY OF SUCH INJURIES, LOSSES, OR D AMA GES. SOME ST A T ES, PR O VINCES, OR COUNTRIES DO NO T ALLO W THE EXCLUSION OR LIMIT A TIONS OF INCIDENT AL OR CONSE- QUENTIAL D AMA GES, SO THE ABO VE LIMIT A TI ON OR EXCLUSION MA Y NO T APPL Y T O Y OU .
A - 1 A Reference Charts Symbology Char ts Note: “m” represents the AIM modifi er character. Refer to International Technica l Specification, Symbology Iden tifiers, for AIM modifier character details. Prefix / Suffix entries for specific symbolog ies ov erride the universal (All Symbologies, 99) en try.
A - 2 2D Symbologies P ostal Symbologies UPC-A ]E0 c 63 UPC-A with Add-On ]E3 c 63 UPC-A with Extended Cou pon Code ]E3 c 63 UPC-E ]E0 E 45 UPC-E with Add-On ]E3 E 45 UPC-E1 ]X0 E 45 Add Honeywell Cod.
A - 3 ASCII Con ver sion Char t (Code P age 1252) In ke yboard appli cations, ASCII Control Characters can be re pres ented in 3 different wa ys, as shown below . The CTRL+X func- tion is OS and application depe ndent. The following table lists some commonly used Microsoft functionality .
A - 4 Lower ASCII Ref erence T able Note: Windows Code page 1252 and lo wer ASCII use the same characters. 23 17 ETB F2 CTRL+ W 24 18 CAN F3 CTRL+ X 25 19 EM F4 CTRL+ Y 26 1A SUB F5 CTRL+ Z 27 1B ESC .
A - 5 63 3F ? 95 5F _ 127 7F ⌂ Extended ASCII Characters DEC HEX CP 1252 ASCII Alternate Extended PS2 Scan Code 128 80 €Ç up arrow ↑ 0x48 129 81 ü down arrow ↓ 0x50 130 82 ‚é right arrow .
A - 6 175 AF ¯» Ctrl Sequence with 1 Character 0x1 D 176 B0 ° ░ 177 B1 ± ▒ 178 B2 ² ▓ 179 B3 ³ │ 180 B4 ´ ┤ 181 B5 µ ╡ 182 B6 ¶ ╢ 183 B7 · ╖ 184 B8 ¸ ╕ 185 B9 ¹ ╣ 186 B.
A - 7 ISO 2022/ISO 646 Character Replacements Code pages define the mappin g of character codes to characters . If the data received does not display with the proper charac- ters, it ma y be because the bar code being scanned was created using a code page th at is diff erent from the one the host pro- gram is e xpecting.
A - 8 China ISO/IEC 646-57 92 99 Great Britain (UK) ISO /IEC 646-04 7 87 F rance ISO /IEC 646-69 3 83 Ger many ISO/IEC646-21 4 84 Switzerland ISO /IEC 646-CH 6 86 Sweden / Finland (extended Anne x C) .
A - 9 Dec 35 36 64 91 92 93 94 96 123 124 125 126 Hex 23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E US 0 1 # $ @ [ ] ^ ` { | } ~ CA 54 95 # $ à â ç ê î ô é ù è û CA 18 96 # $ à â ç ê É ô é ù .
A - 10 Unicode Ke y Maps 6E 70 71 72 73 74 75 76 77 78 79 7 A 7B 7C 7D 7E 4B 50 55 4C 51 56 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 2C 1F 20 21 22 23 24 25 26 27 28 29 2B 39 2E 2F 30 31 32 33 34 35 36 37 53 4F 54 59 3A 3B 3C 3E 3F 38 40 3D 5A 5F 64 5B 60 65 5C 61 66 5D 62 67 63 68 69 6A 6C 104 Key U.
Sample Symbols UPC-A 0 123456 7890 Interleaved 2 of 5 Code 128 EAN-13 Code 39 Codabar 1234567890 Code 128 9 780330 290951 BC321 A13579B Code 93 123456-9$ Code 2 of 5 123456 6543210 RSS-14 (01)00123456.
Sample Symbols Aztec MaxiCode Micro PDF417 Package Label Test Message Test Message PDF417 Postnet Code 49 Car Registration Zip Code 1234567890 Data Matrix QR Code Test Symbol Numbers.
Pr ogramming Char t 0 1 2 3 4 5 6 7 8 9.
.
Pr ogramming Char t Note: If you make an error wh ile scanning the letters or digits (before scanning Save), scan Di scard, scan the correct letters o r digits, and Save again.
Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com 7580-UG Rev C 7/14.
An important point after buying a device Honeywell 7580g (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Honeywell 7580g yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Honeywell 7580g - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Honeywell 7580g you will learn all the available features of the product, as well as information on its operation. The information that you get Honeywell 7580g will certainly help you make a decision on the purchase.
If you already are a holder of Honeywell 7580g, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Honeywell 7580g.
However, one of the most important roles played by the user manual is to help in solving problems with Honeywell 7580g. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Honeywell 7580g along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
