Instruction/ maintenance manual of the product 4500 Honeywell
Go to page of 36
4500 THERMOSTAT INSTALLATION INSTRUCTIONS N7970 7/97.
ii Table of Contents Section 1. GENERAL DESCRIPTION ................................................................................ 1-1 Application and Descriptio n .............................................................................. 1-1 4500 Specificatio ns .
SECTION 1 General Description •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Application and Descrip.
4500 Installation Instructions 1-2 4500 Specifications Operating Range 32 to 122 degrees F., 0 to 50 deg rees C. Temperature Setting Range 45 to 99 degr ees F.
2-1 SECTION 2 Front Panel Controls •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Description ••.
4500 Thermostat Installation Instructions 2-2 You will not be able to adjust room temperature by phone when the 4500 is bypassed. There are s everal uses for the BYPAS S swit ch function: • Allows the u ser to go back to the ir pre-e xisting th ermostat at any time.
3-1 SECTION 3 Installing the 4500 Thermostat •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ General .
4500 Thermostat Installation Instructions 3-2 While installation of the 4500 is possible w ithout the se rvices of a HVAC contractor, some installers will prefe r to have an HVAC contracto r connect the 4500 to the HVAC sy stem and test its op eration.
Section 3. Installing the 4500 Thermostat 3-3 Sometimes , R and Rc are jumpered t ogether at the premi ses t hermostat and are connected to the HVAC system with a single common wire. This is the case if both heating and air conditioning are controlled by the same contro l system .
4500 Thermostat Installation Instructions 3-4 If you are installing the 4500 in a heat on ly system, the setup will lo ok like Figure 4 belo w. R Heat (W) Fan (G) R Heat (W) Fan (G) PREMISES THERMOSTAT 4286 PHONE MODULE IN OUT W G 4500 THERMOSTAT 68 5 3 HVAC System Figure 4.
Section 3. Installing the 4500 Thermostat 3-5 When installing the 4500 the rmostat, refe r to the Summary o f Connectio ns at the back of this manual. This diag ram depicts the 4500's terminal strip and shows e xactly how th e ther mostat mu st be wire d.
4500 Thermostat Installation Instructions 3-6 5. Connect the tagged wires removed in step 4 from the HVAC sys tem to the applicable terminals o f the 4500. Ref er to the f ollowing table for pro per connection information. Table 1 Lead from HVAC system Terminal on 4500 Fan (green) (G) 8 Cool (yellow ) (Y) 7 Heat (white) (W) 6 6.
Section 3. Installing the 4500 Thermostat 3-7 9. Connect the 4500 to the 4286 pho ne modu le using the supp lied key pad type cable. The cable contains fo ur wires of differe nt colors wh ich are conn.
4500 Thermostat Installation Instructions 3-8 10. Once the 4500 is mounted, yo u need to set its DIP sw itch and 3-pin fan control jumper. T h es e procedures are des cribed below. Setting the DIP S witc h The 4500 includes a DIP sw itch for setting the addre ss of the the rmostat.
Section 3. Installing the 4500 Thermostat 3-9 Setting the Fan Control Pins The three fan co ntrol pins in the center of the 4500 are use d to control the operation of the HVAC system’s fan. Us ing the jumper provided, you can select whether or not the sys tem’s fan s hould turn on wit h cooling and heating, or t urn on only with cool ing.
4500 Thermostat Installation Instructions 3-10.
4-1 SECTION 4 Programming the 4286 to Add 4500 Thermostat(s) •••••••••••••••••••••••••••••••••••••••••• In This Sect.
4500 Thermostat Installation Instructions 4-2 To Enter and Use the 4286 Programming Mode: 1. Pick up a premise s touch tone phon e connected to the 4286 handset output. 2. Enter the 2 dig it phone co de on the phon e keyp ad. If the 4286 is announcing, wait until syst em s tatus announcement s have been complete d, then pre ss # 98.
Section 4. Programming the 4286 to Add Thermostat(s) 4-3 If The System Contains Addressable Keypad Non- Addressable Keypad Select “MUTE” (4286 #97 Mode) Comments Thermostat Speake r 01 - 30 (exclu.
4500 Thermostat Installation Instructions 4-4 Field 02: Control Panel Type 1 = Vista-10 and Vista-10SE, Via-30P and Via-30PSE, 4140XMP (with v oice upgrade EPROM) 2 = Vista-20, Vista-20HW and Vista-20SE [default] 4 = Vista-40, Vista-50P, Vista-100, and Vista- 120.
Section 4. Programming the 4286 to Add Thermostat(s) 4-5 The first d igit ind icates the sw ing abo ve the set po int; the se cond digit ind icates the swing below the set po int, as indicated be low: Temperature Span (Swing) “ABOVE “BELOW” Digit #1 Digit #2 1 = 0.
4500 Thermostat Installation Instructions 4-6 For Fields 07-09, s elect the 3-digit wor d codes from Table 5 for eac h des criptor. If you want less than a 3-w ord description for the thermos tat, set unused descriptors to 0 0 0 . Note: Fields 07 throug h 09 select a vo ice announcem ent to be associated with thermostat #1.
Section 4. Programming the 4286 to Add Thermostat(s) 4-7 The first d igit ind icates the sw ing abo ve the set po int; the se cond digit indicates the sw ing below the set p oint, as indicated below: Temperature Span (Swing) “ABOVE “BELOW” Digit #1 Digit #2 1 = 0.
4500 Thermostat Installation Instructions 4-8 For Fields 13-15, s elect the 3-digit wor d codes from Table 5 for eac h des criptor. If you want less than a 3-w ord description for the thermos tat, set unused descriptors to 0 0 0 . Note: Fields 13 thru 15 sele ct a voice anno uncemen t to be associate d with thermostat #2.
Section 4. Programming the 4286 to Add Thermostat(s) 4-9 THERMOSTAT VOICE DESCRIPTORS VOCABULARY (4286 Phone Access Mod ule Only) The follo wing three d igit codes are used to p rogram thermo stat descripto rs into the 4286 programming f ields 07 thru 09 and fields 13 thru 15.
4500 Thermostat Installation Instructions 4-10.
5-1 SECTION 5 Testing the 4500 With the 4286 •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ General .
4500 Thermostat Installation Instructions 5-2 5. Check the heat mode operation of the premi ses t h ermos tat b y varying it s set point and v erifying that the heating sy stem turns on and o ff. 6. If the 4500 thermo stat will control an air co nditioning syste m, set the 4500 front p anel slide sw itches to ACTIVE and COOL .
Section 5. Testing the 4500 With the 4286 Phone Module 5-3 2. Obtain phone a ccess from t he phone module. Enter the 2 -digit phone code. Enter the 4-digit system code i f prompt ed. 3. Press # 99 on the phone k eypad after th e compl ete sta tus announcement .
4500 Thermostat Installation Instructions 5-4 “For set-back on/off, enter 3.” Turning off se t-back will result in it remaining disabled while arme d away, until the ne xt time the sy stem is disarmed.
6-1 SECTION 6 Troubleshooting •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ General ♦ Troubleshoo.
4500 Thermostat Installation Instructions 6-2 4500 or premises thermost at fails to c ontrol the H VAC system. 1. Check set po ints in 4500 and prem ises thermostat to e nsure they are set properly.
A-1 SECTION 7 Appendices •••••••••••••••••••••••••••••••••••••••••• In This Section ♦ Federal Communications Commi.
4500 Thermostat Installation Instructions A-2 ADEMCO Limit ed Warrant y Alarm Device Manufacturing Company , a Division o f Pittway Co rporation, and its divisions, subsidiaries and affiliates (“Sel.
Appendices A-3 1 2 3 4 5 6 7 8 9 10 11 12 5 4 3 2 1 TEMPERATURE SENSOR 1 2 3 FAN CONTROL PINS DOWN UP Cool Heat Fan } TO HVAC SYSTEM } TO 4286 VOICE MODULE } TO PREMISES THERMOSTAT Cool Heat Fan Green.
165 Eileen Wa y , Sy osset, New Y ork, 11791 Copyright © 1997 PITTW A Y CORPORA TION N7970 7/97.
An important point after buying a device Honeywell 4500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Honeywell 4500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Honeywell 4500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Honeywell 4500 you will learn all the available features of the product, as well as information on its operation. The information that you get Honeywell 4500 will certainly help you make a decision on the purchase.
If you already are a holder of Honeywell 4500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Honeywell 4500.
However, one of the most important roles played by the user manual is to help in solving problems with Honeywell 4500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Honeywell 4500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
