Instruction/ maintenance manual of the product QH4000 Honda Automobiles
Go to page of 16
-I.
.
Introduction ..................................................... 1 Safety and Instructional Decals .................................. 2 Assembly 3 Subframe Preparation ........................................... 3 Lift Mechanism ....................
REPLACE IMMEDIATELY IF DAMAGED . ATTACHING INSTRUCTIONS 1. Insert subframe into attachment completely. 2. Lock in place by movin lever forward to " Lock " 3. e ui ed with P.T.O. drive line, connect to trac - 4: If equipped with lift assist springs, lift theattach- osition and secure wit a linch pin.
- - - -- - - --- IMPORTANT: Before beginning assembly of this subframe, make sure tractor is on a level surface, parking brake is set and that engine is turned off, with key removed. su~ERAME-PREP_ARAILoN a) Loosely attach rear hitch plate (fig.1, item 1) to bottom of subframe channel (fig.
Thread the adjustment fork (fig.2, item 5) into the end of the push arm (fig.2, item 3). Adjust the overall length of push arm assembly to 32 13/16 " . Place an 11/16 " f latwasher and a bent retainer plate (fig.2, item 6) on the 5/8" x 4 " bolt (fig.
a) I 6) C) Loosely attach the front support brackets (fig.5, item 1) to the tractor frame. For each bracket, use one lOmm x 1.25 x 25mm bolt (fig.5, item 2) with lockwasher, and two 10mm x 1.25 x 30mm bolts (fig.5, item. 3) with lockwashers for each bracket.
c) Loosely attach front of subframe flatbars (fig.7, item 1) to the outside attaching plates. Use two 1/2" x 1 1/2" bolts (fig.7, item 31, lockwashers and nuts. Install the bolts from the inside as shown. Do not tighten yet. dl Attach the subframe's rear hitch plate (fig.
Tighten the 1/2" bolts (fig.9, item 1). Refer to the Torque Specification Table on page 11. Secure the rear hitch plate (fig.1, item 1) to the tractor by tightening the then the 1/2" x 1 1/4" bolt (fig. 1, item 3). Refer to the Torque Specification Table on page 11.
I I M P O R T A N T I Red ref lectors must be installed on rear fender of tractor when quick hitch is installed. m) Attach the two self adhesive reflectors to the rear fender as illustrated in figure 10. Reflectors should be approximately 1/2" (13mm) up and 6 " (150mm) in from outside corners.
PARTS GUIDE 1 '2 !3 .4 5 6 7 8 9 10 11 12 13 14 15 16 I 17 ~ 18 1 19 30 Front support bracket RH .. 1 Front support bracket LH -. 1 Attaching plate RH ........ 1 Attaching plate LH ........ 1 Hex bolt 10mm x 25mm ...... 2 Hex bolt 10mm x 30mm ...
PARTS GUIDE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Hex bolt 3/8" x 2 1/4" .... 2 Hex nut 3/8", Uni - torque . . 2 Lift lever ................ 1 Adjustment fork ........... 1 Push arm .................. 1 Pin (17/32" x 2 1/4") .
TORQUE SPECIFICATION TABLE GENERAL TORQUE SPECIFICATION TABLE (Revised 2 - 74) USE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN NOTE: Thew valuer apply to fasteners as recciwd from supplier.
Your satisfaction and goodwill are important to your dealer and to us. All Honda warranty details are explained in the Distributor's Limited Warranty. Normally, any problems concerning the product will be handled by your dealer's service department.
.
H/C 3752482 (9307).
An important point after buying a device Honda Automobiles QH4000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Honda Automobiles QH4000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Honda Automobiles QH4000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Honda Automobiles QH4000 you will learn all the available features of the product, as well as information on its operation. The information that you get Honda Automobiles QH4000 will certainly help you make a decision on the purchase.
If you already are a holder of Honda Automobiles QH4000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Honda Automobiles QH4000.
However, one of the most important roles played by the user manual is to help in solving problems with Honda Automobiles QH4000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Honda Automobiles QH4000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
