Instruction/ maintenance manual of the product 08V67-TE0-100A Honda
Go to page of 15
Publications No. Issue Date INSTALLATION INSTRUCTIONS Accessory Application © 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 1 of 15 08V67-TE0-1000- 91 AII 375.
2 of 15 AII 37561-38377 (0711 ) © 2007 America n Honda Motor Co., Inc. – Al l Rights Reser ved. Flange bolt, 6 x 12 mm Flange nut 4 Harness ta pes Accessory User’s Information Manual Back-up Sens.
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 3 of 15 2. Disconnect the negative cable from the battery. 3. Remove the two covers from the rear bumper and remove the rear bump er (two bolts, six self-tapping screws, two clips, and unplug one conne ctor).
4 of 15 AII 37561-38377 (0711 ) © 2007 America n Honda Motor Co., Inc. – Al l Rights Reser ved. 8. Using the trim tool, r emove the rear shelf access panel, then releas e the front rear sp eaker retaining tab. 9. Remove the left rear speaker cover (ni ne retaining tabs).
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 5 of 15 L4 Model 12. Ins tall the cont rol unit to th e vehicle panel: • Partially thread the 6 mm flange nut onto the control unit bracket stud. Inse rt the control unit bracket stud into the hole in the vehicle panel.
6 of 15 AII 37561-38377 (0711 ) © 2007 America n Honda Motor Co., Inc. – Al l Rights Reser ved. 13. Attach the 2A fuse label to the fuse ca se on th e back-up sensor harness.
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 7 of 15 15. At the left taillight, secure the back-up sensor harness to the vehicle h arness wit h one wire t ie. 16. Plug the back-up sensor harness 14 -pin connector into the co ntrol unit, and rou te the harness fo rward along the vehicle harn ess.
8 of 15 AII 37561-38377 (0711 ) © 2007 America n Honda Motor Co., Inc. – Al l Rights Reser ved. 17. Sec ure the back-up sensor harne ss to the vehicle harness with two additional wire ties at the locations shown. L4 Model 742401CE VEHICLE HARNESS BACK-UP SENSOR HARNESS 2 WIRE TIES VEHICLE HARNESS BACK-UP SENSOR HARNESS WIRE TIE V6 MODEL 18.
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 9 of 15 19. Using scissors cut one urethane tape in half, and then cut one of the halves again. Wrap the cu t pieces around the bee per harness shown . 20. Install the connector clip to the beeper 2-pin connector.
10 of 15 AII 37561-38 377 (0711) © 2007 American Ho nda Motor Co., Inc. – All Rig hts Reserved. 742408CE BACK-UP SENSOR HARNESS WIRE TIES WIRE TIE TRUNK ROOM VEHICLE HARNESS 28. Install one wire tie with clip to the holder with the fuse case, and attach the wire tie to the vehicle harness.
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 11 of 15 32. Install one wire tie with h older to the b ack-up sensor harness 16-pin connector , and attach the wire tie to the vehicle harness.
12 of 15 AII 37561-38 377 (0711) © 2007 American Ho nda Motor Co., Inc. – All Rig hts Reserved. 34. While wearing eye protec tion drill the rear bumper: NOTE: Center sensors are 26 mm holes, side sensor s are 24 mm holes. • From the outside of t he bumper, drill all eight pierced marks using a 3 mm drill bit.
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 13 of 15 36. Ins tall two center se nsors into th e 26 mm holes in th e rear bumper using the sensor clip s. Note the direction and location for each sensor. 37.
14 of 15 AII 37561-38 377 (0711) © 2007 American Ho nda Motor Co., Inc. – All Rig hts Reserved. 41. Using isopropyl alcohol on a shop towel, clea n the area where the harness tapes will attach. 42. At each green tape location, attach the back-up sensor subharness to the rear bumper with four harness tapes.
© 2007 Ameri can Honda Mo tor Co., Inc. – All Rights Reserved. AII 37561-38 377 (0711) 15 of 15 44. Check that all wire harnesses are routed pr operly and that all connectors are plugge d in. 45. Rein stall all removed part s. 46. Reconnect the negative cable to the battery.
An important point after buying a device Honda 08V67-TE0-100A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Honda 08V67-TE0-100A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Honda 08V67-TE0-100A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Honda 08V67-TE0-100A you will learn all the available features of the product, as well as information on its operation. The information that you get Honda 08V67-TE0-100A will certainly help you make a decision on the purchase.
If you already are a holder of Honda 08V67-TE0-100A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Honda 08V67-TE0-100A.
However, one of the most important roles played by the user manual is to help in solving problems with Honda 08V67-TE0-100A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Honda 08V67-TE0-100A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
