Instruction/ maintenance manual of the product XA-71-OA Holland
Go to page of 12
XL-FW232-02 GO THE DIST ANCE. FIF TH WHEELS HITCH XA-71 Series Fifth Wheel T op Plates TROUBLESHOOTING AND REBUILD PROCEDURES XA-71-DA 2” SAE Kingpin (Rebuild Kit RK-65014) XA-71-DA-03705 2” SAE K.
2 XL-FW232-02 TROUBLESHOOTING HINTS Fifth Wheel is Hard to Hook Up to T railer: ✔ POSSIBLE CAUSE REMEDY ■ ■ The trailer may be too high; the kingpin Lower the trailer landing gear .
XL-FW232-02 3 1 XA-71-D 1 Fifth wheel top plate for 2 ˝ kingpin 1A XA-71-O 1 Fifth wheel top plate for 3.5 ˝ kingpin 1B XA-71-03706 1 Fifth wheel top plate - 2 ˝ kingpin for FW2570-7103 series or FW2570-7113 series only 1C XA-03711 1 Fifth whl. top plate - 3.
4 XL-FW232-02 REBUILDING PROCEDURES 1. Before attempting to rebuild, review each trouble- shooting hint on page 2 of this manual. Y ou may find that rebuilding is not necessary . 2. If rebuilding is required, check the front page of this manual to be sure you have the correct kit for the fifth wheel you are about to rebuild.
Plunger and Adjustment Wedge Installation 1. Install the adjusting screw ( 20 ) through the hole locat- ed in the throat of the fifth wheel casting. Install the compression spring ( 23 ) over the screw , then slide the adjusting wedge ( 22 ) over the screw (see FIGURE 6 ).
6 XL-FW232-02 REBUILDING PROCEDURES continued Release Arm and Release Lever Installation 1. Check the fit of the release lever ( 15 ) inside the slot in the plunger ( 17 ). The rounded end of the release lever must fit freely into the slot in the plunger .
XL-FW232-02 7 REBUILDING PROCEDURES continued Swinging Lock Installation 1. Place the swinging lock ( 6 ) into position, compressing spring ( 7 ). For spring position, see FIGURE 3 . NOTE: The lock pin ( 5 ) has a hole for a grease fitting ( 25 ). Position the pin so that the hole faces the front of the casting.
8 XL-FW232-02 REBUILDING PROCEDURES continued Adjust the Fifth Wheel Locks: 1. Using a ratchet with 1/2˝ Allen wrench, tighten the adjustment screw ( 20 ) in the throat in the fifth wheel, by turning the screw clockwise until tight.
XL-FW232-02 9 CHECKING THE OPERA TION OF THE FIFTH WHEEL continued Check the Mounting Brackets Before Remounting the T op Plate: 1. Inspect the brackets for cracks or damage, and replace if necessary . 2. Check the rubber bushings for wear . Replace if necessary .
10 XL-FW232-02 T AB ON SWING LOCK LOCK ARM WITH STEP END NO ADJUSTMENT BLOCK AL TERNA TIVE “SECONDARY LOCK INST ALLA TION” FIGURE A ADJUSTMENT BLOCK .
XL-FW232-02 11.
12 XL-FW232-02 HOLLAND USA, INC. 1 950 Industrial Blvd. • P .O. Box 425 • Muskegon, MI 49443-0425 Phone 888-396-6501 • Fax 800-356-3929 www .thehollandgroupinc.
An important point after buying a device Holland XA-71-OA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Holland XA-71-OA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Holland XA-71-OA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Holland XA-71-OA you will learn all the available features of the product, as well as information on its operation. The information that you get Holland XA-71-OA will certainly help you make a decision on the purchase.
If you already are a holder of Holland XA-71-OA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Holland XA-71-OA.
However, one of the most important roles played by the user manual is to help in solving problems with Holland XA-71-OA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Holland XA-71-OA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
