Instruction/ maintenance manual of the product SM6T2 ML-110857 Hobart
Go to page of 12
SM6T2 DISHW ASHER MODEL SM6T2 ML-110857 SM6T2 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 34047 Rev. A (July 2000).
– 2 – Installation, Operation, and Care of MODEL SM6T2 DISHW ASHER SA VE THESE INSTRUCTIONS GENERAL The SM6T2 dishwasher is an electrically controlled, semi-automatic, rack type dishwasher with telescoping hoods, designed for straight-through operation.
– 3 – INST ALLA TION Immediately after unpacking the dishwasher, check for possible shipping damage. If the machine is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, test the electrical service to make sure it agrees with the specifications on the machine data plate.
– 4 –.
– 5 –.
– 6 –.
– 7 – OPERATION INTERLOCK The hoods are interlocked with the Control Handle (Fig. 1) which prevents operation of the automatic wash and rinse cycle with a hood open. Also, the hoods cannot be opened while the dishwasher is in an automatic wash and rinse cycle.
– 8 – AUTOMATIC DISHWASHING Pre-scrap dishes thoroughly to remove large food particles and debris. Never use steel wool on ware that is to be loaded into the dishwasher. Do not allow foreign objects to enter the dishwasher, especially metallic contaminants.
– 9 – CLEANING WARNING : DISCONNECT THE ELECTRICAL POWER SUPPLIES BEFORE CLEANING OR SERVICING THIS MACHINE. The machine must be thoroughly cleaned at the end of each working shift, or at least twice a day. Use only products formulated to be safe on stainless steel.
– 10 – DOs AND DON'Ts FOR YOUR NEW HOBART WAREWASHER DO assure proper water hardness. DO pre-scrap dishes thoroughly. DO use only detergents recommended by your chemical professional. DO at the end of the day, thoroughly cleanse the machine, rinse, and dry (leave hood open).
– 11 – TROUBLESHOOTING To avoid a service call, check symptoms and related possible causes. If machine still does not operate properly, contact Service. SYMPTOM POSSIBLE CAUSE No machine operation. 1. Blown fuse or tripped circuit breaker at power supply.
– 12 – SYMPTOM POSSIBLE CAUSE Inadequate rinse. 1. Dirty line strainer causing reduced water flow. Turn off water supply, remove strainer cap, withdraw and clean screen. Reassemble. 2. Low supply line pressure. 3. Excessive mineral deposits throughout wash and rinse system.
An important point after buying a device Hobart SM6T2 ML-110857 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart SM6T2 ML-110857 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart SM6T2 ML-110857 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart SM6T2 ML-110857 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart SM6T2 ML-110857 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart SM6T2 ML-110857, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart SM6T2 ML-110857.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart SM6T2 ML-110857. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart SM6T2 ML-110857 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
