Instruction/ maintenance manual of the product Q Series Hobart
Go to page of 12
FORM 14580 Rev. L (Jan. 2002) N S T R U C T I O N S I 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com Q SERIES REACH-IN FOOD ST ORA GE CABINETS Q SERIES REACH-IN.
– 2 – Installation, Operation and Care of Q SERIES REA CH-IN FOOD ST ORA GE CABINETS SA VE THESE INSTR UCTIONS GENERAL The Q Series Reach-In Food Storage Cabinets are available as low temperature (0°F), medium temperature (38°F) refrigeration units or hot food storage cabinets (180°F maximum).
– 3 – ASSEMBLY Some components can be removed to allow the cabinet to pass through short or narrow doorways. The door handle can be removed as follows: 1. Remove the screw and bolt from the tumbler. 2. Remove the two mounting screws and the handle assembly (Fig.
– 4 – LEGS OR CASTERS WARNING : THE CABINET MUST BE BLOCKED AND STABLE BEFORE INSTALLING LEGS OR CASTERS. Legs (Fig. 5) To install the legs, raise and block the reach-in a minimum of 7 " from the floor and thread the legs into the Threaded Holes on the bottom of the cabinet.
– 5 – Compressor Mounts Some Q Series units have the compressor specially mounted to help prevent damage during shipment. If the compressor is mounted on shipping blocks, remove the shipping blocks before operating the compressor. If the compressor is mounted on springs, refer to the tag attached to the compressor.
– 6 – STANDARD THERMOMETER (Fig. 9) — The standard digital thermometer is calibrated at the factory and does not permit recalibration. OPTIONAL DIAL THERMOMETER — The optional dial thermometer can be recalibrated. Compare the cabinet thermometer with an accurate test thermometer.
– 7 – ELECTR ONIC DEFROST TIMER (when equipped) If your freezer is equipped with an electronic Defrost Timer, it is located in a control box behind the trim rail at the top of the Reach-In Freezer. To access the the Defrost Timer, remove the Thumbscrew on the left side of the Control Box and slide the Lid to the left (Fig.
– 8 – To Change the Defrost Duration and Bypass the Setting of the Time Clock Begin with the SET CLOCK light blinking rapidly, indicating normal Operation Mode . . . If you want to change the Defrost Duration but not reset the time-of-day, press and hold the PROGRAM button for about 3 seconds until the PROGRAM light starts blinking.
– 9 – How to Set a Custom Defrost Schedule Begin with the defrost timer on normal Operation Mode: The SET CLOCK light is blinking rapidly and the PROGRAM and DEFROST ON lights are off. If all switches are OFF (Fig. 15), the factory preset defrost schedule is enabled: 2 AM , 8 AM , 2 PM , 8 PM .
– 10 – Program Review During normal Operation Mode, with the SET CLOCK light blinking rapidly . . . Press the SET button until the SET CLOCK, PROGRAM, and DEFROST ON lights are lit; then release the SET button and all three lights go off for two seconds.
– 11 – If the Defrost Timer's Battery Loses Power If the SET CLOCK, PR OGRAM and DEFROST ON lights are all b linking, the backup po wer supply (batter y) to the Defrost Timer has weakened. Estimated batter y lif e is 10 years. The timer can continue to function normally after the batter y has weak ened if the timer is reprogrammed.
– 12 – FORM 14580 Rev. L (Jan. 2002) PRINTED IN U.S.A. MAINTENANCE CLEANING Cabinet Clean the inside of the cabinet and the doors weekly with a warm water solution of mild household liquid dishwashing detergent (such as Palmolive green or Ivory). Do not use anything containing grit, abrasive materials, bleach or harsh chemicals.
An important point after buying a device Hobart Q Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart Q Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart Q Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart Q Series you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart Q Series will certainly help you make a decision on the purchase.
If you already are a holder of Hobart Q Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart Q Series.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart Q Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart Q Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
