Instruction/ maintenance manual of the product LT1 ML-104239 Hobart
Go to page of 16
EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO 45374-0001 FORM 18580 Rev. A (8-96) LO W TEMP DISHW ASHER MODEL LT1 ML-104239 LT1 DISHWASHER N S T R U C T I O N S I.
– 2 – T ABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 3 – Installation, Operation and Care of Model L T1 DISHW ASHER SA VE THESE INSTR UCTIONS GENERAL The Model LT1 Dishwasher is a low temperature (140 ° F recommended, 120 ° F minimum), chemical sanitizing, rack-type dishwasher for use with accessory 20" x 20" racks.
– 4 – PL-40920-1 FRONT RACK TRACK AND SPLASH GUARD SCREWS INST ALLA TION UNPACKING Immediately after unpacking the dishwasher, check it for possible shipping damage. If this machine is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.
– 5 – Installation Drawing — 436254.
– 6 – DISH TABLES Dish table end should be turned down and fitted over the lip of the dishwasher tank (Fig. 4). Use an NSF approved sealer between table and tank lip to prevent leaks. Fasten tables to the tank lip; truss head screws (by others) are recommended.
– 7 – ELECTRICAL CONNECTION WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING ON THE CIRCUIT.
– 8 – CYCLE TIMER ADJUSTMENT The cycle timer, which regulates the dishwasher cycle, may require adjustment in order to suit local conditions. To gain access to the cycle timer, loosen the bottom screw on the access cover located on the right side of the control box and rotate the access cover up (Fig.
– 9 – OPERA TION CAUTION: Items made of pewter, aluminum, and silver will be attacked by the sodium hypochlorite sanitizing agent (liquid bleach) used in this machine and therefore should not be washed in it. In addition to these detailed instructions, brief instructions for operation and cleaning can be found on the front of the control box.
– 10 – MACHINE PREPARATION Check to make sure that the pump intake strainer (Fig. 12), the drain pan strainer (Fig. 13), and the drain tube (Fig. 17) are in place and that both strainers are free of debris. The pump intake strainer must drop completely to the bottom of the sump.
– 11 – DISHWASHING Scrape and/or rinse dishes to remove food particles and other debris. Never use steel wool on ware to be loaded into the dishwasher. Place the dishes in a rack. Do not stack dishes on top of each other as water must have free access to all sides of every dish.
– 12 – CLEANING THE DISHWASHER Clean the dishwasher after each working shift. Never use steel wool to clean warewasher surfaces. Use only products formulated to be safe on stainless steel. 1. Drain machine. Turn the P OWER switch Off. 2. Thoroughly cleanse and flush the dishwasher interior and then drain any water that may have accumulated.
– 13 – DOs AND DON'Ts FOR YOUR NEW HOBART WAREWASHER DO assure proper water hardness. DO pre-scrap dishes thoroughly. DO use only detergents recommended by your chemical professional. DO at the end of the day, thoroughly cleanse the machine, rinse, and dry (leave door open).
– 14 – MAINTENANCE DELIMING WARNING : DELIMING SOLUTION MUST NOT COME IN CONTACT WITH BLEACH OR RINSE SOLUTION CONTAINING BLEACH USED IN THIS MACHINE. MIXING MAY CAUSE HAZARDOUS GAS TO FORM. THIS ENTIRE PROCEDURE MUST BE FOLLOWED STEP-BY-STEP FOR SAFE AND SATISFACTORY RESULTS.
– 15 – 13. Run machine without loading dishware for two complete cycles to remove the chemical deliming agent. 14. Reconnect sanitizer, detergent, and rinse aid systems.
– 16 – TROUBLESHOOTING Symptoms that persist after possible causes have been checked may require service. SYMPTOMS POSSIBLE CAUSES No Machine Operation 1. Machine POWER switch in the OFF position. 2. Blown fuse or tripped circuit breaker at power supply.
An important point after buying a device Hobart LT1 ML-104239 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart LT1 ML-104239 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart LT1 ML-104239 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart LT1 ML-104239 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart LT1 ML-104239 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart LT1 ML-104239, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart LT1 ML-104239.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart LT1 ML-104239. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart LT1 ML-104239 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
