Instruction/ maintenance manual of the product HL120 Hobart
Go to page of 20
Models HL120 ML-134296 HL200 ML-134331 HL200 ML-134289 PRIOR ML’S COVERED IN THIS CATALOG HL200 ML-134308 INSTRUCTION MANUAL 701 S. RIDGE AVENUE TROY, OHIO 45374 -0001 937- 332- 3000 · W W W.
2 TABLE OF CONTENTS GENERAL ............................................................................................... 3 INSTALLATION ............................................................................................... 3 Unpacking ....
3 Installation, Operation and Care of Legacy TM 12 & 20-Quart Mixers SAVE THESE INSTRUCTIONS GENERAL The Legacy 12-quart mixer is a bench-type mixer which featu res a S m a r tT i me r™ , a ma nu al b o wl lift and a #12 attach ment hub as standard equipment.
ELECTRICAL CONNE CTIONS (Cord Co nnected Mixer s) WARNING: THE ELECTRICAL CORD ON THIS MACHINE IS EQUIPPED WITH A THREE- PRONGED GROUNDING PLUG WHICH MUST BE CONNECTED TO A PROPERLY GROUNDED RECEPTACLE. IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN.
OPERATION WARNING: MOVING AGITATOR I N BOWL. KEEP HANDS, CLOTHING, AND UTENSILS OUT OF BOWL WHILE IN OPERATION. DO NOT USE WIT HOUT INTERLOCKED GU ARD. The Legacy mixer is equipped with SmartTim er TM c ont rol s. Ref er to Fig. 1 for operating parts and OPERATION section for their functions.
Standard Controls Models HL120/HL200 (With Three Mix Sp eeds Plus Stir Sp eed) DISPLAY MIXING TIME STOPS MIXER STARTS MIXER TIME SELECTOR Fig. 2 SPEED SELECTOR HL120/HL200 Mixer S peeds STIR (Slow) The lowe st speed is for in corporatin g ingredients .
Recipe Timer (Optional) Models HL120/HL200 (With Three Mix Sp eeds Plus Stir Sp eed) Fig. 15 The SmartPlus2 ™ recipe timer has two operating modes, Standard (ST D) and RECIPE. Standard Mode Operates exactl y as the standard controls utilizing continuous and timed mi xing.
BOWL PLACEMENT The bowl must be insta lled before the agitator is installed. To install the bowl, lower the bowl support and po sit ion bowl so the alig nment pins on the left side of the bowl support fit in the holes in the bowl tab . (Fig. 3) Place the slotted tab on bo wl into the lower p art of the pin.
PREPARE FOR MIXING 1. Place the mixing bowl on the b owl support. 2. Pour ingredien ts into the bowl. 9 3. Swing the b owl back to the mix position. 4. Place the a gitator inside the bowl, and th en attach it to the agitator shaft (F ig. 6). 5. Lift bowl support.
Using the Count-Do wn Mode (Timed Mixi ng) 1. Turn the SPEED dial to s elect a mix sp eed. a. If the count-up mode was used for the previous batc h, the desired time needs t o be entered. b. If the count-down mode was use d for the previ ous batch, the pre vious time will be d i s p l a y e d .
RECIPE TIMER OPERATION Recipe Timer Notes • If pause is selected as a mix sp eed, the mi xer START button mus t be presse d to advance to the ne xt recipe step a fter the pause ti me has expired. • If pause has been sel ected, the bowl guard can be o pened and the ti me will continue to count down.
View Recipe When the mi xer is in RECIPE mode, you can vie w the step setti ngs of any recipe. 1. Press the SELECT/SAV E button. A. Display will alternate between spe ed and time. B. The LED of the step being d isplayed will fl ash. 2. Use the arrow buttons to view th e next step.
13 NOTES: • If a value has been assigned for a step number, that LED will be lit. • The LED for the selected step will blink. • If the default value is still assigned to a step, the LED will not be lit. • When programming, the Recipe and Time Selectors are disabled.
UNLOADING 1 . Open the bowl guard wir e cage assembly. 2 . Lower bowl support. 3 . Remove the agitator from the agitator shaft. 4. Slightly lift the bowl off the pin (right side), pull bowl t o the front and remove from the bowl support (left side).
Remove and Clea n Bowl Guard Wire C age (Fig. 11) 1. Rotate wire cage to your left until the three ca rriers align with the carrier escape slots in the circular ridge of the planet ary drip cup. 2. Lift the wire cage straight up so the carr iers escape from the slots on the drip cup.
AGITATORS AND ATTACHMENTS Attachment s for attachment h ub and agitat ors are covere d in a separate Hob art Legacy Mixer Use and App l i c a t i on H a n db o o k on t h e M i x e r O p e r at o r I n fo r m a t io n C D . F o l l ow t h e in s t r uc t i o ns accordingly.
12 & 20 Qt. P Pasty Knife 12 & 20 Qt. Ingredient Chute 12 & 20 Qt. Table CLEANING WARNING: UNPLUG MACHINE POWER CORD BEFORE BEGINNING ANY CLEANING PROCEDURES. The mixer should be thoroughly cleaned daily. DO NOT use a hose to clean the mixer; it sh ou l d be washed with a clean, damp cloth.
MAINTENANCE WARNING: UNPLUG MACHINE POWER CORD BEFORE BEGINNING ANY MAINTENANCE PROCEDURES. Slideway Fig. 13 Fig. 12 Planetary Seal LUBRICATION Slideways The slideways (Fig. 12) sh ould be lubricate d approximately twice a year. T o reach these areas, fully lower the bowl su pport and remove the apro n, which is secured by slott ed screws.
ADJUSTMENTS Agitator Clearance The agitator clea rance shou ld be checked p eri odically. The agit ator must not to uch the bowl and the maximum clearan ce between the bottom of th e bowl and the B flat bea ter is 1/8" ( 3 mm); the maximum clearance between the b ottom of the bowl and the ED do ugh arm is 5/16” (8 mm).
TROUBLESHOOTING Symptoms Poss ible Causes Mixer will not start Flas hing Time Dis play – Se e Below Branch circuit protector is in open position - check fuse or di sconnect swit ch. Mixer is overloaded. Wire ca ge is not in the cl osed posi tion. Bowl is not in close d (mix) position o r if Bowl in not in up position.
An important point after buying a device Hobart HL120 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart HL120 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart HL120 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart HL120 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart HL120 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart HL120, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart HL120.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart HL120. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart HL120 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
