Instruction/ maintenance manual of the product hhtc6 Hobart
Go to page of 12
HHTC SERIES DELI DISPLA Y CASES MODELS HHTC4 ML-132073 (4 FT, TWO-TIER, SELF-SERVICE) HHTC6 ML-132074 (6 FT, TWO-TIER, SELF-SERVICE) HHTC8 ML-132075 (8 FT, TWO-TIER, SELF-SERVICE) FORM 35501 (July 2003) N S T R U C T I O N S I 701 S. RIDGE A VENUE TROY , OHIO 45374-0001 937 332-3000 www .
– 2 – TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
– 3 – Installation, Operation and Care of HHTC SERIES DELI DISPLA Y CASES SA VE THESE INSTRUCTIONS GENERAL The HHTC, Hobart two-tier, self-service series of deli display cases hold hot food products at regulated temperatures maintaining both freshness and quality.
– 4 – Fig. 1 SLOT INST ALLA TION Before installing, check the electrical service to make sure it agrees with the specifications on the machine data plate, located on the operator side of the display case. UNPACKING Immediately after unpacking the display case, check for possible shipping damage.
– 5 – ASSEMBLING THE SLIDING GLASS DOORS 1. Position the top of either door in the top inner track (Fig. 3). 2. Place the bottom of the first door so it straddles the bottom inner guide. Slide door so handle is away from middle. 3. Position the top of the second door in the top outer track.
– 6 – Remove the lower front panel below the controls on the operator side of the display case to access the junction box (lower front panel is attached with 8mm hex head screws). Make electrical connections to the terminal block in the electrical junction box.
– 7 – Fig. 4 OPERA TION WARNING : THE DELI DISPLAY CASE AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING OR SERVICING THE DELI DISPLAY CASE. CONTROLS (Figs. 4, 5) Turning the Power On 1. Turn the Main Power switch to the on position. 3. Turn the Light switch on.
– 8 – Fig. 6 MEMORY — WELL TEMPERATURE CONTROLLER The display case is now programmed, the temperature setting is stored in memory. The programmed temperature setting remains in memory until reprogrammed by the operator, even in the event of power interruption, disconnection or shutdown.
– 9 – PREHEAT 1. Allow the case to preheat 30 to 60 minutes. All doors must be closed in order for unit to preheat properly. 2. Verify that the display case is at the proper temperature. Case temperature displays as shown in (Fig. 8). • During normal operation, the heater output indicator light shows when the heaters cycle on and off (Fig.
– 10 – CLEANING WARNING : THE DISPLAY CASE AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, CLEANING OR SERVICING THE DISPLAY CASE. WARNING : DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. CAUTION: Do not use oven cleaners.
– 11 – MAINTENANCE WARNING : DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOW LOCKOUT / TAGOUT PROCEDURES. WARNING : THE DELI DISPLAY CASE AND ITS PARTS ARE HOT.
– 12 – FORM 35501 (July 2003) PRINTED IN U. S. A. TROUBLESHOOTING Problem Possible Cause Will not operate. 1. Check incoming power. Controller is blank. 2. Check fuses. Replace with same size and type. 3. Turn on the Main Power Switch. 4. Turn on the Lower Heat switch.
An important point after buying a device Hobart hhtc6 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart hhtc6 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart hhtc6 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart hhtc6 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart hhtc6 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart hhtc6, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart hhtc6.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart hhtc6. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart hhtc6 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
