Instruction/ maintenance manual of the product HCR58 Hobart
Go to page of 12
EXECUTIVE OFFICES 701 RIDGE AVENUE TROY, OHIO 45374-0001 FORM 18504 (10-92) MODEL HCR SERIES ELECTRIC RANGE MODELS HCR40 ML-43796 HCR41 ML-43797 HCR42 ML-43798 HCR43 ML-43799 HCR44 ML-43800 HCR45 ML-4.
– 2 – © HOBART CORPORATION, 1992 HCR RANGE MODELS HCR40 HCR46 HCR401 HCR41 HCR47 HCR411 HCR42 HCR48 HCR421 HCR43 HCR49 HCR431 HCR56 HCR561 HCR58 HCR441 HCR40 HCR46 PL - 50911 HCR44 HCR50 HCR51 HC.
– 3 – T ABLE OF CONTENTS P AGE GENERAL ........................................................................................................................................................... 4 INSTALLATION .....................................
– 4 – Installation, Operation and Care of MODEL HCR SERIES ELECTRIC RANGE SA VE THESE INSTRUCTIONS GENERAL The various Hobart Model HCR Series Ranges are equipped as follows: MODEL EQUIPPED WITH R.
– 5 – All ranges are equipped with adjustable 6" legs. Optionally, they may be equipped with no legs (for masonry base mounting) or a 4" toe base in place of legs. Ranges with ovens are equipped with one oven rack. One additional oven rack is available as an option.
– 6 – ELECTRICAL DATA CHARTS RANGES WITH STANDARD OVENS "N/A" RANGES NOT AVAILABLE 480 VOLT 3 PHASE LOAD NOMINAL AMPS PER LINE WIRE TOTAL KW PER PHASE 3 PHASE 1 PHASE KW 208V 240V 480V 208V 240V 480V 208V 240V 480V MODEL CONN. X-Y Y-Z X-Z X Y Z X Y Z X Y Z XYZ XYZ XYZ HCR40,42 21.
– 7 – OPERA TION WARNING: THE RANGE AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING, SERVICING AND CLEANING THE RANGE. BEFORE FIRST USE Clean off the rust preventive compound on the surface units with a cloth dampened with a grease solvent. Wipe with a clean, damp cloth, then dry thoroughly.
– 8 – OVEN CONTROLS (Fig. 1) Thermostat — (located on the right side of the switch panel) controls and maintains oven temperature around the desired set temperature.
– 9 – USING THE OVEN When baking or roasting on one level only, remove rack and place food pans directly on oven deck. When using rack and deck at the same time, rotate foods halfway through cooking cycle. When baking on the rack, it may be necessary to set the bottom 3-heat switch at HI.
– 10 – OPERATING HINTS Preheat the oven and surface units to cooking temperature before cooking the product. Become familiar with the function of the controls and the area of their operation. Avoid excessive door opening. Also avoid direct air current on the oven.
– 11 – CLEANING WARNING: DISCONNECT ELECTRICAL POWER SUPPLY BEFORE CLEANING. Daily (Or More Often If Necessary) 1. Empty and clean grease trays and troughs.
– 12 – TROUBLESHOOTING Unsatisfactory browning of the products baked in the oven is often caused by incorrect installation or operation. The most common problems and their causes are listed below. PROBLEM CAUSES Bottom of product burned - 1. Incorrect switch positions.
An important point after buying a device Hobart HCR58 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart HCR58 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart HCR58 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart HCR58 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart HCR58 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart HCR58, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart HCR58.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart HCR58. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart HCR58 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
