Instruction/ maintenance manual of the product H600 Hobart
Go to page of 16
701 S. RIDGE AVENUE TROY, OHIO 45374-0001 H600 & L800 MIXERS MODELS H600 ML - 104241, 104242, 104383, 104384 L800 ML - 104244, 104245, 104425, 104429 FORM 18812 Rev.
– 2 – © HOBART CORPORATION, 1994 Model H600 Mixer Model L800 Mixer.
– 3 – Installation, Operation, and Care of H600 and L800 MIXERS SA VE THESE INSTRUCTIONS GENERAL The H600 model mixer is a heavy duty 60 quart mixer which features a 2 horsepower motor, a timer, and a #12 attachment hub as standard equipment. With the use of bowl adapters and special agitators, 30 or 40 quart bowls may be used on the H600.
– 4 – INST ALLA TION UNPACKING Immediately after unpacking the mixer, check for possible shipping damage. If this machine is found to be damaged after unpacking, save the packaging material and contact the carrier within 15 days of delivery.
– 5 – ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTION OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT.
– 6 – OPERA TION WARNING : MOVING BEATER IN BOWL, KEEP HANDS, CLOTHING, AND UTENSILS OUT WHILE IN OPERATION, DO NOT USE WITHOUT INTERLOCKED GUARD. Every H600 and L800 mixer is equipped with either an Electro-Mechanical Timer Control (described at the bottom of this page) or a Programmable Timer Controller (described on pages 7 – 9).
– 7 – PROGRAMMABLE TIMER CONTROLLER (when equipped) At Idle, the timer display [ – – : – – ] shows that no time has been set (Fig. 4). Fig. 4 Timer Keys Programming Function (if the mixer is not mixing). P1 Contains up to four preset times.
– 8 – - P1 - P2 01:00 - - - - 1 2 3 4 Indicators above P1 and 1 indicate the first preset time contained in P1. PROGRAMMABLE TIMER CONTROLLER (when equipped) continued Using the Preset Keys, P1 or P2, to set the Mixing Time . . . Each preset key has four time settings.
– 9 – PROGRAMMABLE TIMER CONTROLLER (when equipped) continued To Revise the Preset Mixing Times contained in P1 or P2 . . . Each preset key has four preset time settings. The indicator above the number 1, 2, 3, or 4 and the P1 or P2 indicator light identify which preset time is being displayed.
– 10 – CHANGING SPEEDS The GEAR SHIFT LEVER is used to change speeds. Always stop the mixer before changing speeds. To change speeds, push the STOP button, move the gear shift lever to the desired speed, and restart the mixer by pushing the START button.
– 11 – PL-40071-1 Wire Cage Rotated Left Latch Ridge On Drip Cup Rear Retainer Splash Guard Wire Cage Front-Center Position Front-Center Retainer Centering Ramp Black Release Knob Centering Pin Bowl Guard (Fig. 5) The Wire Cage Assembly on the Bowl Guard can be rotated out-of-the-way to add ingredients or access the bowl and agitator.
– 12 – Attachments To install an attachment, loosen the attachment hub thumb screw and remove the plug. Insert the attachment into the attachment hub, making certain that the square shank of the attachment is in the square driver of the mixer. Secure the attachment by tightening the thumb screw.
– 13 – MAINTENANCE W A RNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT BEFORE BEGINNING ANY MAINTENANCE PROCEDURE. LUBRICATION Planetary The planetary oil should be checked periodically.
– 14 – Transmission The transmission oil should be even with the line on the Oil Level Gauge when the motor is NOT running. If the oil falls below this line, DISCONNECT ELECTRICAL POWER SUPPLY and remove the Top Cover, which is secured by two screws.
– 15 – ADJUSTMENTS Agitator Clearance The agitator clearance should be checked with each bowl change. The agitator must not touch the bowl and the maximum clearance between the bottom of the bowl and the B Flat Beater is 1 ⁄ 8 " ; the maximum clearance between the bottom of the bowl and the E or ED Dough Arm is 5 ⁄ 16 ".
– 16 – SERVICE If service is needed on this equipment, contact your local Hobart Service Office. FORM 18812 Rev. B (12-99) PRINTED IN U.S.A. TROUBLESHOOTING SYMPTOMS POSSIBLE CAUSES Mixer will not start. 1. Gear shift lever between gears (not fully engaged).
An important point after buying a device Hobart H600 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hobart H600 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hobart H600 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hobart H600 you will learn all the available features of the product, as well as information on its operation. The information that you get Hobart H600 will certainly help you make a decision on the purchase.
If you already are a holder of Hobart H600, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hobart H600.
However, one of the most important roles played by the user manual is to help in solving problems with Hobart H600. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hobart H600 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
