Instruction/ maintenance manual of the product JPEG2000 Hitachi
Go to page of 80
JPEG2000 S t and alone DVR User Guide - 1 - Date: 2006/07/05 VER: 1.5 Caution ……………………………………………………………………. 3 Package ……………………………………………………………………. 3 S pecification …………………………………………………………………….
JPEG2000 S t and alone DVR User Guide - 2 - Disclaimer: The product names menti oned in this manual a re used a s ident ification s only , while the cop yright of these names might belong to other companies. The product spec and info are for reference only , and they may be updated from time to time without notification.
JPEG2000 S t and alone DVR User Guide - 3 - For you safety , unplug the power before moving the DVR, installing, or replacing any p arts or hard drive. Make sure all the power cable and wires are properly se t up before using the DVR. Contact your distributor immediately if there is any defect.
JPEG2000 S t and alone DVR User Guide - 4 - Model 4/8/16 CH JPEG2000 St and Alone DVR Video Input 4/8/16CH VIDEO IN 1.0 VP-P ， 75OHM(BNC TYPE) Video Output (BNC TYPE) X 2 Video I/O VGA Output Suppor.
JPEG2000 S t and alone DVR User Guide - 5 - Protocol TCP/IP Netw ork Remote monitoring Remote Sof teware: Remote live view , playback, and save as A VI IE: Remote live view , backup, and save backup t.
JPEG2000 S t and alone DVR User Guide - 6 - 1-1 Front p anel introduction 1.[CD-R W] Built-in CD-R W for CD-R back-up. 2.[IR Receiver & LED Lamps] IR Remote Controller Receiver . DVR S tatus LED: RUN- Flashes when play picture by picture through J.
JPEG2000 S t and alone DVR User Guide - 7 - 10.[Control] SEQ- Full screen sequencing or the smaller screen sequencing in PIP mode. PIP- For entering the Picture in Picture mode from full screen mode. NEXT - Switch other control keys in PTZ mode.
JPEG2000 S t and alone DVR User Guide - 8 - 1-2 Back p anel introduction [4Channel] [8Channel] [16Channel] 1.[RS485, Relay Output, Sensor Input] RS485, for direct connection to PTZ cameras. 16 sensor input s and 1 relay output. 2.[VGA Output] Connection to a VGA monitor or TFT LCD.
JPEG2000 S t and alone DVR User Guide - 9 - 1-3 IR remote controller introduction 1.[MENU] Enter menu or exit 2.[S plit /OSD] 4S: 4 split 9S: 9 split 16S: 16 split OSD: OSD words on/of f 3.[1~16 Channel] Switch channel in live or playback; password entering 4.
JPEG2000 S t and alone DVR User Guide - 10 - 2-1 Camera and monitor inst allation 2-1-1 Camera inst allation Connect camera to DVR camera in CH1~CH16 ※ Please do not start the DVR before the camera.
JPEG2000 S t and alone DVR User Guide - 1 1 - 2-1-3 Loop out inst allation T o monitor a single channel, connect the “loop out” of the corresponding channel to a monitor . T o record a specific channel individually , connect the “loop out” of the corresponding channel to a DVR, VCR, or other record device.
JPEG2000 S t and alone DVR User Guide - 12 - 2-2-3 Relay output inst allation Alarm output can be NO or NC, depending on the settings. NO-COM: the NO and COM terminals are open-circuit, and it’ll become closed-circuit when alarm triggered.
JPEG2000 S t and alone DVR User Guide - 13 - # 2 RxD # 3 TxD # 5 GND TxD # 3 GND # 5 RxD # 2 DVMR unit Other device (PC) D-SUB 9 cable ( twisted RS-232C c able) T o connect DVR to a PC, users must use a twisted RS232 cable, as the illustration. 2-3-3 PTZ camera inst allation Please connect the PTZ’ s D+ to the DVR’s D+ , and D- to D-.
JPEG2000 S t and alone DVR User Guide - 14 - 2-4 HDD inst allation [Step s] 1. Disassemble the bolts as illustrated. 2.Jumper setting Set up the HDD as MASTER or SLA VE. Please refer to the HDD manual of the jumper settings. 3.HDD Installation Please insert the HDD as shown in , and make sure the HDD is set as “MASTER”.
JPEG2000 S t and alone DVR User Guide - 15 - 2-5 Power plugging Insert the adapter to the rear power socket of DVR. Insert the power cable to the other side of adapter . Plug in the power cable and power on the DVR. Caution: Please use a 100~240V AC 50~60HZ and 12VDC 8A or 5A pow er supply or it may damage the DVR.
JPEG2000 S t and alone DVR User Guide - 16 - 3-1 Display configuration 1.[T ime] Current system time or the recorded time in playback 2.[Date] Current system date or t he recorded date in playback 3.[Camera title] Camera title of the displayed channel.
JPEG2000 S t and alone DVR User Guide - 17 - 3-2 Screen switch/OSD position adjust Press the number button to switch to the corresponding channel for its full screen view Mode: press to switch among diff erent split modes: 4/6/8/9/13/16 splits.
JPEG2000 S t and alone DVR User Guide - 18 - 3-4-2 Freeze in Full mode In full screen mode, Press FREEZE to freeze the channel, and press FREEZE again to cancel. 3-5 V iew in sequence Press SEQ to enter Sequential Switch and press SEQ again to cancel.
JPEG2000 S t and alone DVR User Guide - 19 - 3-6 Zoom view Go to the channel to be zoomed and press ZOOM to enl arge to 200%, use direction buttons to move the enlarged part. Use the direction buttons to choose an area and pre ss ENTER to zoom.
JPEG2000 S t and alone DVR User Guide - 20 - 3-8 Record Emergency record (Red): press REC to start emgergency record at continuous record mode and at the best resolution and quality .
JPEG2000 S t and alone DVR User Guide - 21 - 3-9 Playback 3-9-1 Play/S top Press PLA Y key on front panel to st art playback st arting from the last playback time. Press“ PLA Y ”during playback to c hoose to play forward or backward. Press“ ST OP ”key to stop playback.
JPEG2000 S t and alone DVR User Guide - 22 - 3-9-3 SEARCH BAR Using +/- keys to select the recording percent age of the search bar . Press “ ENTER ”key to confirm and start the playback. 3-9-4 TIME/DA TE 1.[ST AR T] The start time and date of recording It shows that the st art time and date of the recording dat a.
JPEG2000 S t and alone DVR User Guide - 23 - 3-9-6 Playback speed adjustment s While playback, using the direction keys to adjust the playback speed.
JPEG2000 S t and alone DVR User Guide - 24 - 4-1 Log-In 4-1-1 DVR LOG-IN Press MENU to login DVR system. Use CH. SELECT ORS 1~0 to key in the password. Then press ENTER to confirm and enter the system. Erase the wrong password by PIP key .
JPEG2000 S t and alone DVR User Guide - 25 - 4-2 Display setup 1 . [ S C R E E N D I S P L A Y ] Set up which information to be displayed at the Live and Playback mode. 2.[MONIT OR SETUP] Adjust the VGA display resolution and the monitor color .
JPEG2000 S t and alone DVR User Guide - 26 - 4-2-2 Monitor setup 1.[VGA SETUP] Set up the VGA resolution. 2.[COLOR BAR TEST] Adjust the monitor colors by the color bar .
JPEG2000 S t and alone DVR User Guide - 27 - 7 . [ B U Z Z E R S E T U P ] Set the Buzzer ON or OFF at a cert ain condition. 8.[P ASSWORD SETUP] Setup the password. 9.[SYSTEM INFORMA TION] Show the system information, such as the versions of S/W and H/W , HDD model number , and CD-R model number .
JPEG2000 S t and alone DVR User Guide - 28 - 4-3-2 Time/date setup The date and time set by the manufacture r maybe dif f erent from your time zone. It is very important to set up t hey system date and time before the DVR start s recording. Set the date and time by using direction buttons and [-][+] button or Jog shuttle.
JPEG2000 S t and alone DVR User Guide - 29 - [CAMERA COLOR SETUP] Adjust the image color: Use [UP] and [DOW N] to select an item and use [-] and [+] or Jog shuttle to adjust the values. CHANNEL: Select the camera to be modified. BRIGHTNESS: Adjust image brightness (-32~31).
JPEG2000 S t and alone DVR User Guide - 30 - [MOTION SETUP] 1.[CHANNEL] Select a channel for the setup. 2.[SENSITIVITY GRADE] Adjust motion detection sensitivity . 1 (LOW)~4 (VERY HIGH) 3.[MOTION DISPLA Y TYPE] Setup the display type that marks the motion area.
JPEG2000 S t and alone DVR User Guide - 31 - 4-3-4 Interval setup 1.[SWITCH INTER V AL] FULL- Full Screen Sequence Interval setup. (Range: 1~99 SEC) PIP- Picture in Picture, the sub-pictur e’s sequence interval setup.
JPEG2000 S t and alone DVR User Guide - 32 - 4-3-6 Event popup setup 1.[CHANNEL] Use [+] and [-] to select a channel. 2.[POPUP ON/OFF] Set up the POPUP function ON/OFF: Use [+ ] and [-] to select ON or OFF . When there is an event, the screen display will switch to a full screen of the corresponding channel.
JPEG2000 S t and alone DVR User Guide - 33 - 4-3-8 Password setup The p assword consist s of 1 to 8 digits. Press the number keys on the front panel to enter the password and you can use any co mbination of the numbers from 1 to 10 . 1.[USER ID] Press e or f to set User ID.
JPEG2000 S t and alone DVR User Guide - 34 - 4-4 Record setup 1.[RECORD CONFIGURA TION] Set up overwrite, recording mode, pict ure quality , resolution, and recording speed. 2.[SCHEDULE SETUP] Program the recording schedule. 3.[HOLIDA Y SETUP] Set up holidays, max.
JPEG2000 S t and alone DVR User Guide - 35 - 4.[RESOLUTION] By lowering the resolution, the DV R gains the recording speed but the recorded pictures becom smaller .
JPEG2000 S t and alone DVR User Guide - 36 - 4-4-2 Schedule record Program a recording schedule throught out the year . MODE : Press MODE to select an editing mode. Use the direction keys to move the cursor , and then press [+] and [-] to select a recording mode.
JPEG2000 S t and alone DVR User Guide - 37 - 4-4-3 Holiday setup Set up the holidays through out the year . Y ou can program up to 100 days as holidays. The recording schedule of the ho lidays is the same as the settings of Sunday . Press MODE and set the editing mode as EDIT HOLIDA Y .
JPEG2000 S t and alone DVR User Guide - 38 - 4-6 External device 1.[TCP/IP SETUP] Set up the DVR’s TCP/IP information. 2.[RS232C SETUP] Set up the parameters of the RS232 port. 3.[P ANTIL T SETUP] Set up the parameters of the PTZ control.
JPEG2000 S t and alone DVR User Guide - 39 - [IP CONFIG SETUP] Press ENTER to enter a selection. Use to move the cursor . Use [+] [-] or J.Shuttle to change the value, and press EN TER to confirm the setting and exit the selection. Use to go to another selection and repeat the previous steps.
JPEG2000 S t and alone DVR User Guide - 40 - [CONNECTION SETUP] U s e to select and [+] [-] or J.Shuttle to change the value. 1.[TIMEOUT] Set up the remote connection response ti me, if the client does not receive responses from the DVR for certain dur ation, the client will disconnect the connection and try again.
JPEG2000 S t and alone DVR User Guide - 41 - 4-6-3 Pantilt setup < COMMAND SETUP > < SPEED SETUP > [COMMAND SETUP] Press to select and [+] / [-] to change the value. 1.[CHANNEL] Select PTZ channel. 2.[MODEL] Select PTZ protocol.
JPEG2000 S t and alone DVR User Guide - 42 - [SPEED SETUP] Press to select and [+] / [-] to change the value. 1.[P AN SPEED] Set the P ANing speed. 2.[TIL T SPEED] Set the TIL T ing speed. 3.[ZOOM SPEED] Set the speed of ZOOM IN/OUT .
JPEG2000 S t and alone DVR User Guide - 43 - 5-1 Dat a backup 1.[HDD] Indicate the start and the end recording date and time of the HDD(s). 2.[CD-R] Select a starting date and time for backup. Press ENTER and use ef to move the cursor . Use [+] [-] or J.
JPEG2000 S t and alone DVR User Guide - 44 - 5-2 CD Player sof t w are installation 1.Insert software CD. 2. Click [Inst all CD-R backup player] to start the installation. 3. Select a Destination Folder 4. Copy files to the Destination Folder . System will build a new icon of [CD BACKUP PLA YER] on PC [DESKTOP].
JPEG2000 S t and alone DVR User Guide - 45 - 5-3 CD Player sof t w are interface 1.Display screen: T o display the backup image 2.T ime display: T o indicate the current time 3.Information window: T o indicate the CD’s st art/end time and date, and the backup video quality (resolution).
JPEG2000 S t and alone DVR User Guide - 46 - Open AJP file 1. Select (OPEN) and the window below will show up on the screen. 2. Select the file and click [OPEN] to open the AJP file. Save JPG file 1. During playback and under FULL SCREEN MODE, when y ou see the picture you want to save, click EDIT .
JPEG2000 S t and alone DVR User Guide - 47 - 6-1 PTZ camera Inst allation 6-1-1 Connection Setup Connect the PTZ’s D+ to the DVR’s D+, and D- to D-. 6-1-2 PTZ setup [EXTERNAL DEVICE] SYSTEM MENU ` EXTERNAL DEVICE ` P ANTIL T SETUP ` COMMAND SETUP 1.
JPEG2000 S t and alone DVR User Guide - 48 - 6-2 PTZ camera operation Use MENU and NEXT key to select a PTZ command, and [+] [-] to select the channel. Then, press PTZ key to enter the PTZ control mode. Indicate the channel connected with a PTZ camera.
JPEG2000 S t and alone DVR User Guide - 49 - 7-1 Network Introduction Users have to indentify what kind of In ternet access they have before they set up the DVR’s network p arameters. DSL and cable modem are the most popular broadband technologies.
JPEG2000 S t and alone DVR User Guide - 50 - 7-2-2 V ia ADSL First, identiry if you have S tatic IP or Dynamic IP serv ice. If you do not know , ask your ISP (Internet Service Provider). If you have S tatic IP , your ISP should prov ide you a st atic IP address, which will never change even when you reboot your modem.
JPEG2000 S t and alone DVR User Guide - 51 - [Via ADSL with Dynamic IP] If you have ADSL with Dynamic IP addre ss, the network administrator assigns you an IP address from their pool when y ou or your ISP reboots the network and you may get a different IP address from time to time.
JPEG2000 S t and alone DVR User Guide - 52 - 7-3 Router setup There is a wide selection of routers in the market. They may be very dif ferent in terms of confi guration and operation. Here is an example of how to set up a router . For details, please read your router ’s manual.
JPEG2000 S t and alone DVR User Guide - 53 - [PPPoE setup] Select PPPoE in W AN connection T ype Enter User Name and Passward provided by your ISP The router will get the IP address u pon c onne ction. In this example, we get the IP address of 21 1.20.
JPEG2000 S t and alone DVR User Guide - 54 - 7-4 Client sof tware 7-4-1 Inst all and setup Insert the Install CD into CD-ROM, and the computer will auto-run the Install program. W e suggest installing the software on Windows XP or Windows 2000. 1.[Install Client sof tware] Click [Install Client sof tware].
JPEG2000 S t and alone DVR User Guide - 55 - 7-4-3 Sof tware operation [Remote viewer interface] 1.[Live Display ] Remote DVR Live display 2.[Current St atus ] T o show the current status 3.
JPEG2000 S t and alone DVR User Guide - 56 - 7-4-4 Client sof tware setup [IP/PORT] 1.[DVR NAME] Enter the DVR’s location or name 2.[IP LIST] Show the list of saved DVR IP addresses. If you are connecting to a DVR in this list, you can simply click it from the list, enter the DVR Admin’s password, and press SA VE and then OK.
JPEG2000 S t and alone DVR User Guide - 57 - [DDNS] 1.[Group] Enter Group name registered on DDNS Server . Please refer to 7-5 DDNS setup and operation for det ails. 2.[DVR Name] Enter DVR name registere d on DDNS Server . If the DVR name is entered and saved before, click LOAD to browse the list.
JPEG2000 S t and alone DVR User Guide - 58 - [PTZ/SA VE] 1.[Circular Monitoring Interval] Set up a sequential switch interval. 2.[Scan Rate] Select a Fast forward (FF) speed of remote Playback. 3.[PTZ T ype] Select the protocol used by your PTZ camera.
JPEG2000 S t and alone DVR User Guide - 59 - 7-4-6 Remote playback When the DVR is connected, cli ck [PLA YBACK] to enter Playback interface. [ Remote Playback Interface ] 1.[Playback Picture] T o show the playback video 2.[T ime/Date Selection] T o select time/date of playback 3.
JPEG2000 S t and alone DVR User Guide - 60 - [Search button] 1. Fast Reward (RW) 2. Fast Forward (FF) 3. RW (S peed 1X) 4. S top / Pause 5. Playback (S peed 1X) 6. Go to the beginning of recording 7. Jump to the previous hour 8. Jump to the next hour 9.
JPEG2000 S t and alone DVR User Guide - 61 - 7-4-7 Back up via Client sof tware Save the recorded data as single JPEG picture or A VI format. [Save the recorded data as single JPEG picture] Press “STOP” right before where you want to save and press “SA VE”.
JPEG2000 S t and alone DVR User Guide - 62 - 7-5 DDNS setup and operation DDNS SERVER setup 1. Connect to DDNS SERVER(http://advr .com.tw or http://59.
JPEG2000 S t and alone DVR User Guide - 63 - 4. Select “ADD DVR” to add DVR information 5. Add DVR information: DVR NAME: Set a DVR name MAC ADDRESS: Enter the DVR’s MAC address.
JPEG2000 S t and alone DVR User Guide - 64 - DVR setup 1. The DVR setup is a onetime ef fort. First, make sure your DVR can be accessed over the Internet.
JPEG2000 S t and alone DVR User Guide - 65 - 2. Select DDNS in [IP/PORT] setup 3.Go to DDNS setup [DDNS INFO] GROUP : Enter Group nameregistered on DDNS Server . DVR NAME : Enter DVR name registered on DDNS Server . If the DVR name is entered and saved before, click LOAD to browse the list.
JPEG2000 S t and alone DVR User Guide - 66 - Configuration of DDNS connection 1. DVR connect to DDNS server automatic ally and update the IP address by it self. 2. The client accessesto DDNS server and requests IP address from DDNS server . 3. DDNS server replies the DVR’s IP address and port number .
JPEG2000 S t and alone DVR User Guide - 67 - Users can also a ccess to t he DVR fro m Internet Explore for remote viewin g, remote backup, and playback the backup file. Log on to DDNS server and go to the DVR List Remote Live V iew via IE Brow ser Click WEB to link to your DVR 1.
JPEG2000 S t and alone DVR User Guide - 68 - PTZ: Select the protocol BAUDRA TE: Select the baud rate C H : S e l e c t t h e I D o f P E Z c a m e r a Z O O M : Z o o m i n / o u t FOCUS: Focus near/far IRIS: IRIS open/close Web Network Backup Click “Backup” to open the web page “W eb Network Backup” 1.
JPEG2000 S t and alone DVR User Guide - 69 - 2. Function setup: Connect T e st: T o test the connection status Unlock: T o get the record start/End time of DVR Set Backup T ime: Set the start/end time, size and path of file backup S tart Backup: Active the backup function 3.
JPEG2000 S t and alone DVR User Guide - 70 - Play backup file Click [Backup Player] to open the web page of “Backup Player” 1. Display the backup image 2. Indicate the present time of monitoring 3. Indicate the start/end time of backup file 4.
JPEG2000 S t and alone DVR User Guide - 71 - 8. Function keys: OPEN: Open the backup file EDIT : Edit the backup image A VI SA VE: T o save the A VI file EXIT : Log out the program 9. audio options: ON: T o start the audio function Ch1~4: to select the channel with audio Save A VI file: 1.
JPEG2000 S t and alone DVR User Guide - 72 - [4ch DVR] ※ The numbers are for reference only . ※ The recording duration is caculated under the continuous recording mode (Record speed :1/1X) Appendix.
JPEG2000 S t and alone DVR User Guide - 73 - [8/16ch DVR] ※ The numbers are for reference only . ※ The recording duration is caculated under the continuous recording mode (Record speed :1/1X).
JPEG2000 S t and alone DVR User Guide - 74 - Appendix.2 System configuration.
JPEG2000 S t and alone DVR User Guide - 75 - Install USB driver 1. Connect USB port between PC and DVR 2. Press and hold Search and Play keys on front panel and power on DVR 3. The DVR beeps for a moment. 4. When the Windows system detect new device, please select [Install fr om a list or specific location] 5.
JPEG2000 S t and alone DVR User Guide - 76 - 7. S tart to copy the driver to Windows system. 8. After installation, the USB device [BulkUsb.Sys Usb Bulk I/O Driver] can be found from [Device Manager].
JPEG2000 S t and alone DVR User Guide - 77 - Install USB upgrade program Insert the Install CD 1.Please select :[Install USB upgrade program(Allupdate) 2. Set up Directory ※ (default Directory : "C:Program FilesJ2000Allupdate") After installation, there’ll be a shortcut on desktop.
JPEG2000 S t and alone DVR User Guide - 78 - Upgrade firmware Up date procedures Ste p 1 、 Update BOOT 1. Connect the USB port between DVR and PC. (Do not power on DVR in advance) 2. Execute USB update program AUDTOT AL ， select “Boot” then choose t he file: _FBoot_0000_16M_V2.
JPEG2000 S t and alone DVR User Guide - 79 - Ste p 2 、 Update F/W 1. Select ALLUPDA TE then choose the file: _ALLUPDA TE_4J_NTIC_noboot_V1.3.bin 2. Press and hold SEARCH and PLA Y and power on the DVR 3. When the DVR is turned on, you will hear very shor t beeps.
JPEG2000 S t and alone DVR User Guide - 80 - Introduction PLA Y ONL Y MODE can be used in the following situations: When you need to playback a hard drive from another DVR When you need to playback the video which you deleted by running HDD CLEAR Enter “PLA Y ONL Y MODE” Turn on the DVR.
An important point after buying a device Hitachi JPEG2000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hitachi JPEG2000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hitachi JPEG2000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hitachi JPEG2000 you will learn all the available features of the product, as well as information on its operation. The information that you get Hitachi JPEG2000 will certainly help you make a decision on the purchase.
If you already are a holder of Hitachi JPEG2000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hitachi JPEG2000.
However, one of the most important roles played by the user manual is to help in solving problems with Hitachi JPEG2000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hitachi JPEG2000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
