Instruction/ maintenance manual of the product FDS 9DVA Hitachi
Go to page of 60
English 1 MODE D’EMPLOI ET INSTRUCTIONS DE SECURITE AVERTISSEMENT Une utilisation incorrecte et dangereuse de cet outil motorisé peut entraîner la mort ou de sérieuses blessures corporelles! Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.
English 2 CONTENTS English Page IMPORTANT INFORMATION ............................. 3 MEANINGS OF SIGNAL WORDS ....................... 3 SAFETY .................................................................... 4 GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS .
English 3 IMPORTANT INFORMATION Read and understand all of the operating instructions, safety precautions and warnings in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions.
English 4 SAFETY GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS 1.
English 5 4. Tool Use and Care (1) Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. (2) Do not force tool. Use the correct tool for your application.
English 6 SPECIFIC SAFETY RULES AND SYMBOLS 1. Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “ live ” wire will make exposed metal parts of the tool “ live ” and shock the operator.
English 7 IMPOR T ANT SAFETY INSTRUCTIONS FOR BA TTER Y CHARGER 1. This manual contains important safety and operating instructions for battery charger Model UC9SD and UC12SD. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
English 8 10. Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman. 11. Do not disassemble battery charger; take it to a qualified serviceman when service or repair is required.
English 9 DISPOSAL OF THE EXHAUSTED BATTERY WARNING: Do not dispose of the exhausted battery. The battery must explode if it is incinerated. The product that you have purchased contains a re- chargeable battery.
English 10 FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool.
English 11 2. Battery Charger (UC9SD and UC12SD) Model FDS9DVA FDS12DVA Motor DC motor No-load speed Low 0 – 280/min 0 – 350/min High 0 – 840/min 0 – 1050/min Capacity Drilling Wood (Thickness 23/32"(18mm) 13/16"(21mm) 11/16" (18mm)) (Soft Wood) (Soft Wood) Metal (Thickness 3/8" (10mm) 15/32" (12mm) 1/16"(1.
English 12 ASSEMBL Y AND OPERA TION APPLICATIONS 䡬 Use as a drill Drilling of soft steel, wood, plastic and aluminum materials. 䡬 Use as a screwdriver Tightening and loosening of machine screws, wood screws and tapping screws. REMOVAL AND INSTALLATION METHOD OF BATTERY 䡬 How to install the battery.
English 13 3. Charging 䡬 When the plug of battery charger has been inserted into the receptacle, charging will commence and the pilot lamp will light on. NOTE: If the pilot lamp dose not light, pull out the plug from the receptacle and check if the battery is properly mounted.
English 14 (2) Avoid recharging at high temperatures. A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened.
English 15 3. Check the rotational direction The bit rotates clockwise (viewed from the rear side) by pushing the R-side of the selector button. The L-side of the selector button is pushed to turn the bit counterclockwise. (See Fig. 6). (The L and R marks are provided on the body.
English 16 5. Confirm the cap position (see Fig. 9) The tightening torque of this unit can be adjusted accord- ing to the cap position, at which the cap is set. (1) When using this unit as a screwdriver, line up the one of the numbers “ 1, 3, 5 ... 22 ” on the cap, or the black dot, with the triangle mark on the outer body.
English 17 THE SCOPE AND SUGGESTIONS FOR USES Table 3 HOW TO SELECT TIGHTENING TORQUE Table 4 NOTE: The selected content shown in Table 4 indicates the differences according to screw type, screw size and material used. CAUTION: ● While operating the Cordless driver drill, take care not to lock the motor.
English 18 MAINTENANCE AND INSPECTION CAUTION: Pull out battery before doing any inspection or maintenance. 1. Checking the condition of the bit. The bits should be checked regularly. If worn or broken bits can slip or decrease the efficiency of the motor and burn it out.
English 19 ACCESSORIES WARNING: Accessories for this power tool are mentioned in this Instruction Manual. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage. NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.
English 20 OPTIONAL ACCESSORIES.....sold separately 1. Battery (FEB9S)(For FDS9DVA) 2. Battery (FEB12S)(For FDS12DVA) NOTE Specifications are subject to change without any obligaiton on the part of the HITACHI.
Français 21 INFORMATIONS IMPORTANTES Lire et comprendre toutes les instructions de fonctionnement, les précautions de sécurité et les avertissements dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.
Fran ç ais 22 SECURITE REGLES GENERALE DE SECURITE – POUR TOUS LES OUTILS FONCTIONNANT SUR BATTERIE AVERTISSEMENT: Lire et coxmprendre toutes les instructions. Un non respect de toutes les instructions ci-dessous peut entra î ner une é lectrocution, un incendie et/ou de s é rieuses blessures personnelles.
Fran ç ais 23 4. Utilisation de l ’ outil et entretien (1) Utiliser un é tau ou toutes autres fa ç ons de fixer et maintenir la pi è ce à usiner sur une plate-forme stable. Tenir la pi è ce avec la main ou contre son corps est instable et peut conduire à une perte de contr ô le de l ’ outil.
Fran ç ais 24 REGLES DE SECURITE SPECIFIQUES ET SYMBOLES 1. Tenir les outils par les surfaces de grippage lors de la r é alisation d ’ op é ration o ù l ’ outil de coupe risque d ’ entrer en contact avec des c â bles cach é s.
Fran ç ais 25 CONSIGNES DE S É CURIT É IMPOR- T ANTES POUR LE CHARGEUR DE BA TTERIE 1. Ce manuel renferme des consignes de s é curit é et d ’ utilisation importantes pour le chargeur de batterie mod è le UC9SD et UC12SD.
Fran ç ais 26 * Si l ’ intensit é nominale d ’ entr é e du chargeur de batterie est donn é e en watts et non en amp è res, calculer la capacit é en amp è res correspondante en divisant la capacit é en amp è res par la capacit é de tension, par exemple : 9.
Fran ç ais 27 8. NE JAMAIS ins é rer de corps é trangers dans l ’ orifice de la batterie ou du chargeur de batterie. 9. NE JAMAIS utiliser de transformateur- é l é vateur pour la recharge. 10. NE JAMAIS utiliser de g é n é rateur de moteur ni d ’ alimentation CC pour la recharge.
Fran ç ais 28 DESCRIPTION FONCTIONNELLE REMARQUE: Les informations contenues dans ce mode d ’ emploi sont con ç ues pour assister l ’ utilisateur dans une utilisation sans danger et un entretien de l ’ outil motoris é .
Fran ç ais 29 2. Chargeur de batterie (UC9SD et UC12SD) SPECIFICATIONS 1. Perceuse-visseuse à batterie 2. Chargeur de batterie Fig. 2 Plaque de pr é caution Orifice d ’ installation de la batteri.
Fran ç ais 30 ASSEMBLAGE ET FONCTIONNEMENT UTILISATIONS 䡬 Utilisation comme m è che Per ç age d ’ acier doux, de bois, de plastique et d ’ aluminium. 䡬 Utilisation comme tournevis Serrage et desserrage de vis à m é taux, vis en bois et vis auto-taraudeuses.
Fran ç ais 31 AVERTISSEMENT: Ne pas utiliser le cordon é lectrique s ’ il est endommag é . Le faire r é parer imm é diatement. 3. Recharge 䡬 Quand la fiche du chargeur de batterie est ins é r é e dans la prise, la recharge commence et la lampe t é moin s ’ allume.
Fran ç ais 32 Comment prolonger la dur é e de vie des batteries (1) Recharger les batteries avant qu ’ elles ne soient compl è tement é puis é es.
Fran ç ais 33 2. V é rifiez si la batterie a é t é correctement install é e. 3. V é rifiez la direction de rotation. La m è che tourne dans le sens horaire (vu de l ’ arri è re) quand on appuie sur c ô t é -R du s é lecteur. En appuyant sura c ô t é -L du s é lecteur la m è che tourne dans le sens anti- horaire.
Fran ç ais 34 5. V é rification de la position du capuchon. (Voir Fig. 9) Le couple de serrage de cet outil peut ê tre r é gl é suivant la position du capuchon. (1) Quand la perceuse est utilis é e avec un tournevis, aligner un des nombres “ 1, 3, 5 .
Fran ç ais 35 PRECAUTION: 䢇 Il se peut que la rotation du moteur se v é rouille et s ’ arr ê te pendant que l ’ outil est utilils é en tant que perceuse. Pendant le fonctionnement de la perceuse-visseuse, faites attention à ne pas verrouiller le moteur.
Fran ç ais 36 S É LECTION DU COUPLE DE SERRAGE Tableau 4 REMARQUE: Le Tableau 4 indique les diff é rences en fonction du type de vis, de la longueur de la vis et du mat é riau utilis é . PRECAUTION: ● Lors de l ’ utilisation de la perceuse-visseuse à fil, faire attention de ne pas bloquer le moteur.
Fran ç ais 37 ENTRETIEN ET INSPECTION PRECAUTION: Sortir la batterie avant toute op é ration d ’ inspection ou d ’ entretien. 1. V é rifier l ’é tat de la m è che.
Fran ç ais 38 1 ACCESSOIRES AVERTISSEMENT: Les accessoires pour cet outil motoris é sont mentionn é s dans ce mode d ’ emploi. L ’ utilisation de toute autre fixation ou accessoire peut ê tre dangereux et causer des blessures ou des dommages m é caniques.
Fran ç ais 39 ACCESSOIRES EN OPTION.....vendus s é par é ment 1. Batterie (FEB9S)(Pour FDS9DVA) 2. Batterie (FEB12S)(Pour FDS12DVA) REMARQUE: Les sp é cifications sont sujettes à modification sans aucune obligation de la part de HITACHI.
Español 40 INFORMACIÓN IMPORTANTE Antes de utilizar o realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las instrucciones de operación, las precauciones de seguridad, y las advertencias de este Manual de instrucciones.
Espa ñ ol 41 SEGURIDAD NORMAS GENERALES DE SEGURIDAD – PARA TODAS LAS HERRAMIENTAS ALIMENTADAS CON BATER Í A ADVERTENCIA: Lea y entienda todas las instrucciones. Si no sigue las instrucciones indicadas a continuaci ó n, pueden producirse descargas el é ctricas, incendios, y/o lesiones serias.
Espa ñ ol 42 4. Utilizaci ó n y cuidados de la herramienta (1) Utilice abrazaderas u otra forma pr á ctica de asegurar y sujetar la pieza de trabajo sobre una plataforma estable. La sujeci ó n de la pieza de trabajo con la mano o contra su cuerpo puede ser inestable y conducir a la p é rdida del control.
Espa ñ ol 43 NORMAS Y S Í MBOLOS ESPEC Í FICOS DE SEGURIDAD 1. Sujete las herramientas por las superficies de empu ñ adura aisladas cuando realice una operaci ó n en la que la herramienta de corte pueda entrar en contacto con cables ocultos.
Espa ñ ol 44 INSTRUCCIONES IMPOR T ANTES DE SEGURIDAD P ARA EL CARGADOR DE BA TER Í AS 1. Este manual contiene instrucciones importantes de seguridad para el cargador de bater í as modelo UC9SD y UC12SD.
Espa ñ ol 45 9. No utilice el cargador de bater í as con un cable o un enchufe da ñ ado. Si est á n da ñ ados, reempl á celos inmediatamente. 10. No utilice el cargador de bater í as si ha recibido un golpe, si ha ca í do, o si est á da ñ ado de alguna otra forma.
Espa ñ ol 46 14. SIEMPRE desconecte el cable de alimentaci ó n del tomacorriente cuando no vaya a utilizar el cargador. ELIMINACI Ó N DE LAS BATER Í AS AGOTADAS ADVERTENCIA: No tire las bater í as agotadas. Las bater í as pueden explotar si se incineran.
Espa ñ ol 47 Fig. 1 DESCRIPCI Ó N FUNCIONAL NOTA: La informaci ó n contenida en este Manual de instrucciones ha sido dise ñ ada para ayudarle a utilizar con seguridad y mantener esta herramienta el é ctrica.
Espa ñ ol 48 2. Cargador de bater í as (UC9SD y UC12SD) ESPECIFICACIONES 1. Taladro atornillador a bater í a Fig. 2 Placa de precauci ó n Orificio de instalaci ó n de la bater í a L á mpara piloto 2.
Espa ñ ol 49 Fig. 3 Cierre Presionar Asidero Insertar Bater í a L á mpara piloto Fig. 4 Sacar MONT AJE Y OPERACI Ó N APLICACIONES 䡬 Utilizaci ó n como taladro Taladrado de materiales de acero d.
Espa ñ ol 50 ADVERTENCIA: No utilice el cargador si su cable est á da ñ ado. Haga que se lo reparen inmediatamente. 3. Carga 䡬 Al insertar la clavija del cargador de bater í a en el enchufe se inicia la carga y se encender á la l á mpara piloto.
Espa ñ ol 51 Forma de hacer que las bater í as duren m á s (1) Recarque las bater í as antes de que se hayan agotado completamente. Si siente que la potencia de la herramienta el é ctrica se debilita, deje de utilizarla y recargue su bater í a.
Espa ñ ol 52 2. Confirmar que la bater í a est á puesta correctamente. 3. Examinar la direcci ó n de rotaci ó n La broca rota hacia la derecha (mir á ndola desde atr á s) al oprimir el lado R (der.) de inversi ó n. El lado L (izq.) se usa para hacer girar la broca a la izquierda.
Espa ñ ol 53 5. Confirmar la posici ó n de la cubierta (Ver la Fig. 9) El par de apriete de esta unidad puede ajustarse de acuerdo con la posici ó n de la cubierta. (1) Cuando utilice esta unidad como destornillador, alinee uno de los n ú meros “ 1, 3, 5 .
Espa ñ ol 54 Tenga cuidado de no bloquear el motor mientras que se est á operando el atorniilador taladro. 䢇 Cuando ponga el mando de cambio en “ HIGH ” (alta velocidad) y la posici ó n de la tapa sea “ 17 ” o “ 22 ” , puede ser que el embrague no se aplique y que el motor se bloquee.
Espa ñ ol 55 NOTA : El contenido seleccionado mostrado en la Tabla 4 indica las diferencias de acuerdo con el tipo de tornillo, el tama ñ o del tornillo, y el material utilizado. PRECAUCI Ó N: ● Cuando utilice el taladro/destornillador inal á mbrico, tenga cuidado de no bloquear el motor.
Espa ñ ol 56 MANTENIMIENTO E INSPECCI Ó N PRECAUCI Ó N: Extraiga la bater í a antes de realizar cualquier trabajo de inspecci ó n o de mantenimiento. 1. Comprobaci ó n de las condiciones de la broca Las brocas deber á n comprobarse regularmente.
Espa ñ ol 57 1 ACCESSOIRES ADVERTENCIA: Los accesorios para esta herramienta el é ctrica se mencionan en este Manual de instrucciones. La utilizaci ó n de otros accesorios puede resultar peligrosa y causar lesiones o da ñ os mec á nicos. NOTA: Las especificaciones est á n sujetas a cambio sin ninguna obligaci ó n por parte de HITACHI.
Espa ñ ol 58 ACCESORIOS OPCIONALES.....de venta por separado 1. Bater í a (FEB9S)(Para FDS9DVA) 2. Bater í a (FEB12S)(Para FDS12DVA) NOTA: Las especificationes est á n sujetas a cambio sin ninguna obligaci ó n por parte de HITACHI.
Espa ñ ol 59 Parts are subject to possible modification without notice due to improvements. FDS12DVA Item Part Name No. 1 Special Screw (Left Hand) M5 × 35 2 Drill Chuck 10TLRD-N 3 Gear Box Ass&apos.
Espa ñ ol 60 109 Code No. C99096762 Printed in China Shinagawa Intercity T ower A, 15-1, Konan 2-chome, Minato-ku, T okyo 108-6020, Japan Issued by Hitachi Koki Canada Co. 3950 Steve Reynolds Blvd. Norcross, GA 30093 6395 Kestrel Road Mississauga ON L5T 1Z5 Distributed by Please contact HITACHI KOKI U.
An important point after buying a device Hitachi FDS 9DVA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hitachi FDS 9DVA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hitachi FDS 9DVA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hitachi FDS 9DVA you will learn all the available features of the product, as well as information on its operation. The information that you get Hitachi FDS 9DVA will certainly help you make a decision on the purchase.
If you already are a holder of Hitachi FDS 9DVA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hitachi FDS 9DVA.
However, one of the most important roles played by the user manual is to help in solving problems with Hitachi FDS 9DVA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hitachi FDS 9DVA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
