Instruction/ maintenance manual of the product CPX-327 Hitachi
Go to page of 42
Liquid Crystal Projector CP-S317/CP-X327 (CP-S317W/CP-X327W) USER'S MANUAL Vol.2 Extended Please read this user's manual thoroughly to ensure correct usage through understanding. BEDIENUNGSANLEITUNG Teil 2 Fortsetzung Bitte lessen Sie diese Benutzerhandbuch zugunsten der korrekten Bedienung aufmerksam.
1 ENGLISH LCD Projector CP-S317/CP-X327 USER'S MANUAL USER'S MANUAL V ol.1 (Basic) Page PROJECTOR FEATURES ................2 PREPARATIONS ..............................2 PART NAMES ...................................4 SETTING UP THE PROJECTOR .
2 ● Ultra High Brightness Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly efficient optical system ● Partial Magnification Function Interesti.
3 ENGLISH 1 Connect your devices to the projector Connect your computer, VCR and/or other devices you will be using to the projector. Insert the batteries into the remote control 2 13 3 Connect the power cord (1) Connect the connector of the electrical power cord to the AC inlet of the main unit.
STANDBY/ON INPUT KEYSTONE RESET LANP TENP PO W ER 4 P ART NAMES THE PROJECTOR Zoom ring 15 Focus ring 15 Air filter 27 Elevator button 6 Elevator button 6 KEYSTONE button 20 STANDBY/ON button 14 INPUT.
5 ENGLISH THE REMOTE CONTROL STANDBY/ON button 14 VIDEO button 15 MENU button 23 RGB button 15 BLANK button 22 SEARCH button 22 VOLUME button 17 MUTE button 17 KEYSTONE button 20 ASPECT button 22 AUTO.
6 Adjusting the Projector's Elevator Feet 1 Press and hold in the elevator buttons 2 Raise or lower the projector to the desired height and then release the elevator buttons When you release the elevator buttons, the elevator feet will lock into position.
7 ENGLISH Refer to the illustrations and tables below to determine the screen size and projection distance. Adjusting the Screen Size and Pr ojection Distance Top view a c b Lens center The screen Sid.
8 Display monitors 12 DVD players 11 VCRs 11 Laptop computers 10 Desktop computers 10 Indicates the corresponding reference page ATTENTION Precautions to observe when connecting other devices to the projector • Whenever attempting to connect other devices to the projector, please thoroughly read the manual of each device to be connected.
9 ENGLISH Ports and Cables Refer to the table below to find out which projector port and cable to use for connecting a given device. Use this table for determining which cables to prepare. About Plug-and-Play Capability • This projector is compatible with VESA DDC 1/2B.
10 B A AUDIO IN COMPONENT VIIDEO R L / (MONO) VIDEO IN C R / R R C B / P B Y K S-VIDEO IN USB 1 RGB IN 2 RGB OUT CONTROL A B B AUDIO IN AUDIO cable RGB cable AUDIO OUT RGB IN Analogue RGB OUT Laptop c.
11 ENGLISH B C A If using a component video connection If using an audio/video connection AUDI O IN COMPONENT VIIDE O R L / (MONO) VI DEO IN C R / R R C B / P B Y K S-VIDEO IN USB 1 RGB IN 2 RGB OUT C.
12 RGB cable A AUD IO IN COMPONENT VIIDEO R L / (MONO) VIDEO IN C R / R R C B / P B Y K S-VIDEO IN USB 1 RGB IN 2 RGB OUT CONTROL A RGB OUT RGB IN CONNECTING YOUR DEVICES (continued) Connecting to a Display Monitor Display monitor CP-S317/327W/最終 02.
13 ENGLISH 1 Remove the battery cover Slide back and remove the battery cover in the direction of the arrow. Insert the batteries Align and insert the two AA batteries (that came with the projector) according to their plus and minus terminals (as indicated in the remote control).
14 STANDBY/ON INPUT KEYSTONE RESET LA NP TEN P P O W ER 1 Make sure that the power cord is firmly and correctly connected to the projector and outlet 2 Turn on the projector's power Set the power switch to [ | ] (ON). The projector will go to STANDBY mode and the POWER indicator will light to solid orange.
RGB 15 ENGLISH 6 Use the zoom ring to adjust the screen size 7 Use the focus ring to focus the picture 5 If selecting RGB input Press the RGB button Press this button to toggle between the devices connected to RGB IN 1 and 2. As illustrated below, each time you press the RGB button, the projector switches between RGB IN 1 and 2.
16 VIDEO ASPECT HOME END MUTE P AGE DOWN KEYSTONE FREEZE OFF ON MENU POSITION ENTER ESC RESET P AGE UP VOLUME MAGNIFY AUT O BLANK RGB SEARCH ST ANDBY/ON 1 Press the STANDBY/ON button (control panel or remote control) The message "Power off?" will appear on the screen for approximately 5 seconds.
17 ENGLISH VIDEO ASPECT HOME END MUTE P AGE DOWN KEYSTONE FREEZE OFF ON MENU POSITION ENTER ESC RESET P AGE UP VOLUME MAGNIFY AUT O BLANK RGB SEARCH ST ANDBY/ON 1 Press the VOLUME button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the volume.
18 VIDEO ASPECT HOME END MUTE P AGE DOWN KEYSTONE FREEZE OFF ON MENU POSITION ENTER ESC RESET P AGE UP VOLUME MAGNIFY AUT O BLANK RGB SEARCH ST ANDBY/ON 1 Press the POSITION button As illustrated on the right, a dialog will appear on the screen to aid you in adjusting the position.
19 ENGLISH The automatic adjustment operation requires approximately 10 seconds. Also, please note that it may not function correctly with some input signals. NOTE 1 USING THE AUTOMA TIC ADJUSTMENT FEA TURE Press the AUTO button Horizontal position (H.
20 • This function may not be work well with some types of input signals. • The adjustable range for correcting keystone distortions will vary with the type of input signal. NOTE CORRECTING KEYSTONE DIST ORTIONS 1 Press the KEYSTONE button As illustrated on the right, a dialog will appear on the screen to aid you in correcting the distortion.
21 ENGLISH The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT, AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state.
22 SIGNAL SEARCHING SELECTING THE ASPECT RA TIO TEMPORARIL Y BLANKING THE SCREEN 1 Press the SEARCH button When you press the SEARCH button, the projector begins searching for input signals. If it detects an input signal, the search will cease and the projector will project the detected signal.
23 ENGLISH USING THE MENU FUNCTIONS 1 Press the MENU button The menu display appears on the screen. The projector has the following menus: MAIN, PICTURE 1, PICTURE 2, INPUT, SCREEN, and OPTION. Select a menu using the / buttons. The current settings of the items that can be manipulated via the selected menu appear.
24 You can use the remote control as a simplified mouse or keyboard. OPERA TING THE PC SCREEN CAUTION Caution: Mistaken use of the mouse/keyboard control could damage your equipment. • Only connect to a PC. • Before connecting, read the manuals of the device you will connect.
25 ENGLISH THE LAMP HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately: DT00511 for CP-S317/DT00521 for CP-X327), then contact your local dealer.
26 • The LAMP indicator is also red when the lamp unit reaches high temperature. Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again. If the LAMP indicator is still red, replace the lamp. NOTE THE LAMP (continued) Replacing the lamp All projector lamps will wear out eventually.
27 ENGLISH THE AIR FIL TER Caring for the air filter The air filter should be cleaned about every 100 hours. If the LAMP indicator and TEMP indicator blink red simultaneously, or a message prompts you to clean the air filter when you turn on the unit, the filter needs to be cleaned.
28 THE AIR FIL TER (continued) Replacing the air filter If the soiling will not come off the air filter, or it becomes damaged, then it needs to be replaced. Please contact your local dealer, after confirming the model of your separately sold replacement air filter.
29 ENGLISH OTHER CARE Caring for the inside of the projector : In order to ensure the safe use of your projector, please have it cleaned and inspected by your local dealer about once every 2 years. Never try to care for the inside of the unit yourself.
30 REGULATORY NOTICES REGULATORY NOTICES WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
1 TECHNICAL TECHNICAL TECHNICAL SIGNAL CONNECTOR PIN ASSIGNMENT RGB IN [1]/[2] RGB OUT D-sub 15-pin Shrink Mini Din 4-pin S-VIDEO Mini Din 4-pin Pin No Signal 1 Color: 0.286Vp-p (NTSC, burst signal), 75 Ω terminator 0.3Vp-p (PAL/SECAM, burst signal), 75 Ω terminator 2 Brightness: 1.
2 Resolution H × × V fH (kHz) fV (Hz) Rating Signal mode Display mode CP-S317 CP-X327 720 × 400 37.9 85.0 VESA TEXT Zoom in Zoom in 640 × 480 31.5 59.9 VESA VGA (60Hz) Zoom in Zoom in 640 × 480 35.0 66.7 Mac13"mode Zoom in Zoom in 640 × 480 37.
3 TECHNICAL The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, refer to adjust the V.
4 CONNECTION TO THE MOUSE CONTROL 1 2 3 4 1 2 3 4 + 5V — DATA + DATA GND + 5V — DATA + DATA GND 1 23 4 2 1 3 4 USB jack (B type) USB jack (A type) Projector USB cable Computer ADB Mouse 2 1 4 3 6 .
5 TECHNICAL (1) Turn off the projector and computer power supplies and connect with the RS-232C cable. (2) Turn on the computer power supply and after the computer has started up, turn on the projector power supply.
6 Requesting projector status (Get command) (1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’) from the computer to the projector. (2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
7 TECHNICAL Command data chart Names Operation type Header Command data CRC Action Type Setting code Blank Color Set Blue BE EF 03 06 00 CB D3 01 00 00 30 03 00 White BE EF 03 06 00 6B D0 01 00 00 30 .
8 Command data chart (continued) Names Operation type Header Command data CRC Action Type Setting code H.Position Reset Execute BE EF 03 06 00 IC D3 06 00 03 70 00 00 H.
9 TECHNICAL Names Operation type Header Command data CRC Action Type Setting code Contrast Get BE EF 03 06 00 FD D3 02 00 04 20 00 00 Increment BE EF 03 06 00 9B D3 04 00 04 20 00 00 Decrement BE EF 0.
10 Command data chart (continued) Names Operation type Header Command data CRC Action Type Setting code Tint Get BE EF 03 06 00 49 73 02 00 03 22 00 00 Increment BE EF 03 06 00 2F 73 04 00 03 22 00 00.
Printed in Japan *QR53891* Hitachi America, Ltd. Computer Division 2000 Sierra Point Parkway, MS760 Brisbane, CA 94005-1835 Tel: +1-800-225-1741 Fax: +1-650-244-7776 www.hitachi.com/lcd. Hitachi Canada, Ltd. 6740 Campobello Road, Mississauga, Ontario L5N2L8, Canada Tel: +1-905-821-4545 Fax: +1-905-821-1101 Hitachi Home Electronics (Europe), Ltd.
An important point after buying a device Hitachi CPX-327 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hitachi CPX-327 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hitachi CPX-327 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hitachi CPX-327 you will learn all the available features of the product, as well as information on its operation. The information that you get Hitachi CPX-327 will certainly help you make a decision on the purchase.
If you already are a holder of Hitachi CPX-327, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hitachi CPX-327.
However, one of the most important roles played by the user manual is to help in solving problems with Hitachi CPX-327. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hitachi CPX-327 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
