Instruction/ maintenance manual of the product CM650ET Hitachi
Go to page of 16
HITACHI COLOUR MONITOR USER MANUAL MANUEL D’UTILISATION CM650ET BEDIENUNGSANLEITUNG with EasyMenu ! MANUAL DE USUARIO MANUALE DI ISTRUZIONI E EasyMenu is HITACHI’s On Screen Display function for easy operation. READ THE INSTRUCTIONS INSIDE CAREFULLY.
NOTE: The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. TRADEMARK ACKNOWLEDGEMENT VGA is a registered trademark of International Business Machines Corporation.
Congratulations! You have just purchased a TC0’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Below you will find a brief summary of the environmental requirements met by this product. The complete environmental criteria document may be ordered from: TCO Development SE- 114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco.
FEATURES ...................................................................................................... I-1 CAUTIONS ..................................................................................................... 1-2 ’ I! INSTALLATION .
n NEVER REMOVE THE REAR COVER ! __ The rear cover MUST be removed only by authorised service personnel. This colour - monitor contains high voltage components.
n CAUTION for 200 - 240V operation only This equipment relies on the protective devices in the building installation for short-circuit and over-current protection. Refer to the following table for the suitable number and location of the protective devices which should be provided in the building installation.
H FCC (Federal Communications Commission) STATEMENT WARNING WARNING : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed - to provide reasonable protection against harmful interference in a residential installation.
n FOR THE CUSTOMERS IN THE U.K. THIS PRODUCT IS SUPPLIED WITH A TWO PIN MAINS PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K. PLEASE REFER TO THE NOTES ON THIS PAGE.
Install the monitor in the following way, taking care to maintain safety FRONT VIEW Control Panel Tilt & Swivel Base v Rear Cover Signal Input Connector AC Inlet - Power Cord REAR VIEW USB Slot / 7J-J - to a receptacle of to the host computer - (for the optional USB HUB Module) the correct voltage 1.
Microprocessor-based preset functions can store 26 sets of geometry settings including the standard settings. The following industrial standard settings have been pre- 1! programmed by the factory. - - No. Video Mode Name Horizontal Video Mode (with Resolution and Vertical Frequency) Frequency 1 VGA 640 x 400- 70 Hz 31.
Power LED Power Switch Switches Switches Switch POWER ON/OFF Press the Power switch, to switch the power ON or OFF. n When power is ON, the power LED lights. n After turning OFF the switch, wait at least 5 seconds before restarting the monitor. Otherwise the monitor may operate incorrectly.
Table-l Function - + PINCUSHION PIN BALANCE recalls the factory preset modes. When the Green reaches When the Blue or Red the upper limit, it makes the reaches the upper limit, it Blue and Red weaker. make the Green weaker. B makes the Red and Green makes the Blue stronger.
Table-l (continued) Function - + B H.MOIRE makes the operation of makes the operation of horizontal moire circuit horizontal moire circuit weaker. stronger. @nJ V.MOIRE makes the operation of makes the operation oi vertical moire circuit weaker. vertical moire circuit stronger.
When the monitor has detected the change of the signal input condition, the monitor will indicate the condition automatically, as follows. II! - - the horizontal frequency Precision frequency, Horizontal *2kHz mode. Refer to MANAGEMENT SYSTEM” below.
= CRT - - I- input Signal Synchronisation Resolution Video Clock frequency Viewable Image Size Viewable Image Area Colour Temperature Warm-up Time Power Supply Dimensions Weight Environmental Condition USB HUB (optional) Specification and Design are subject to change without notice.
An important point after buying a device Hitachi CM650ET (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hitachi CM650ET yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hitachi CM650ET - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hitachi CM650ET you will learn all the available features of the product, as well as information on its operation. The information that you get Hitachi CM650ET will certainly help you make a decision on the purchase.
If you already are a holder of Hitachi CM650ET, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hitachi CM650ET.
However, one of the most important roles played by the user manual is to help in solving problems with Hitachi CM650ET. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hitachi CM650ET along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
