Instruction/ maintenance manual of the product C 7YA Hitachi
Go to page of 68
DOUBLE INSULATION DOUBLE ISOLATION AISLAMIENTO DOBLE INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS WARNING Improper and unsafe use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety.
CONTENTS Page IMPORTANT INFORMATION ..................... 3 MEANINGS OF SIGNAL WORDS ............... 3 SAFETY ............................................................ 4 SAFETY RULES ........................................... 4 SERVICE AND REPAIRS .
English 3 IMPORTANT INFORMATION Read and understand all of the operating instructions, safety precautions and warnings in the Instruction Manual before operating or maintaining this power tool. Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions.
English 4 SAFETY SAFETY RULES WARNING: Death or serious bodily injury could result from improper or unsafe use of power tools. To avoid these risks, follow these basic safety instruc- tions: READ ALL INSTRUCTIONS 1. NEVER TOUCH MOVING PARTS. Never place your hands, fingers or other body parts near the tool ’ s moving parts.
English 5 10. KEEP CHILDREN AWAY. Do not let visitors contact tool or extension cord. All visitors should be kept safely away from work area. 11. DON ’ T FORCE TOOL. It will do the job better and safer at the rate for which it was intended. 12. USE RIGHT TOOL.
English 6 Have defective switches replaced by the authorized service center. Do not use tool if switch does not turn it on and off. 23. NEVER USE A POWER TOOL FOR APPLICATIONS OTHER THAN THOSE SPECIFIED. Never use a power tool for applications other than those specified in the Instruction Manual.
English 7 37. KEEP BLADES CLEAN AND SHARP. Sharp blades minimize stalling and kickback. 38. DANGER: KEEP HANDS AWAY FROM CUTTING AREA. Keep hands away from blades. Do not reach underneath work while blade is rotating. Do not attempt to remove cut material when blade is moving.
English 8 Keep blades sharp. Support large panels as shown in Fig. 1 . Use fance or straight edge guide when ripping. Don't fence tool. Stay alert exercise control. Don't remove saw from work during a cut while the blade is moving. 43. LOWER GUARD.
English 9 50. Before setting the tool down after completing a cut, be sure that the lower (telescoping) guard has closed and the blade has come to a complete stop . 51. Never attempt to saw any material like metal and so on that give off sparks. Such action can lead to fire or injury.
English 10 USE OF EXTENSION CORD Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
English 11 DOUBLE INSULATION FOR SAFER OPERATION To ensure safer operation of this power tool, HITACHI has adopted a double insulation design. “ Double insulation “ means that two physically separ.
English 12 FUNCTIONAL DESCRIPTION NOTE: The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool. Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool NAME OF PARTS Fig.
English 13 Work piece Base Saw Blade ASSEMBL Y AND OPERA TION APPLICATIONS 䡬 Cutting fiber cement board (Ex. HARDI PLANK, HARDI PANEL) PRIOR TO OPERATION 1. Power source Ensure that the power source to be utilized conforms to the power source requirements specified on the product nameplate.
English 14 7. Check if clamp lever and wing bolt are tightened. If the wing bolt to adjust cutting depth (Fig. 12) and wing bolt to adjust angle of inclination (Fig. 13) are loose, injury can result. Make sure that they are tightened securely. 8. Check performance of safety cover WARNING: Make absolutely sure that the safety cover is not fixed.
English 15 When you find it difficult to inspect the blade tip, or in case of inclined cutting, or when you use the guide for cutting, loosen the screw, move the slide cover upward and make necessary adjustment before use. (For inclined cutting, fix the slide cover in the uppermost position.
English 16 CUTTING PROCEDURES WARNING: ● Never touch the moving parts. ● Should the saw blade be stopped or make an abnormol noise during operation, turn off the switch immediately. ● Don't remove circular saw from work piece during a cut while the saw blade is moving.
English 17 5. Release the safety cover lever. When the safety cover contacts the work piece surface, it will be in proper position to open freely when cutting is commencend. 6. Holding the saw in position, with the blade not contacting the work piece surface, pull the trigger.
English 18 USE OF DUST BAG WARNING: ● To avoid serious accident, ensure the switch is in the OFF position, and disconnect the plug from the receptacle. ● Never attempt to saw any material like metal and so on that give off sparks. Such action can lead to fire or injury.
English 19 1. Mounting the dust guide (1) Insert the dust guide ’ s thrusting mouth into the adapting mouth of the body. (Fig. 21) (2) Turn the dust guide and point it in the desired direction to discharge sawdust.
English 20 Fig. 24 MAINTENANCE AND INSPECTION WARNING: To avoid serious accident, ensure the switch is in the OFF position and disconnect the plug from the receptacle during maintenance and inspection.
English 21 (1) Turn the base face up (Fig. 25) and loosen the wing-nut. (2) Apply a square to the base and the saw blade and, turning the slotted set screw with a slotted- head screwdriver, shift the position of the base to produce the desired right angle.
English 22 ACCESSORIES WARNING: Accessories for this power tool are mentioned in this Instruction Manual. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage. NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.
Français 23 INFORMATIONS IMPORTANTES Lire et comprendre toutes les instructions de fonctionnement, les précautions de sécurité et les avertissements dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.
Fran ç ais 24 SECURITE REGLES DE SECURITE AVERTISSEMENT: Une utilisation incorrecte ou dangereuse des outils é lectriques peut entra î ner la mort ou des blessures graves.
Fran ç ais 25 Les outils projettent des é tincelles pendant qu ’ ils fonctionnent. Ne jamais utiliser les outils dans un lieu renfermant de la laque, de la peinture, du diluant, de l ’ essence, des gaz, des produits adh é sifs ni aucun autre mat é riau combustible ou explosif.
Fran ç ais 26 Ne jamais utiliser l ’ outil si l ’ on est sous l ’ influence d ’ alcool, de drogues ou de m é dicaments qui rendent somnolent.
Fran ç ais 27 para î t d é fectueux, arr ê ter de l ’ utiliser imm é diatement et le faire r é parer par un centre de service Hitachi autoris é . 32. NE JAMAIS LAISSER FONCTIONNER L ’ OUTIL SANS SURVEILLANCE. LE METTRE HORS TENSION. Ne pas abandonner l ’ outil avant qu ’ il ne soit compl è tement arr ê t é .
Fran ç ais 28 40. UTILISER LE GUIDE DE REFENTE. Toujours utiliser un guide de refente ou un guide à bord rectiligne pour effectuer une refente. 41. AVERTISSEMENT : Il est important de soutenir la pi è ce correctement et de tenir solidement la scie pour é viter toute perte de contr ô le pouvant entra î ner des blessures physiques.
Fran ç ais 29 48. Placer la section large de l ’ embase de la lame sur la section de la pi è ce qui est fermement soutenue, et non sur la section qui va tomber apr è s la coupe. A titre d ’ exemple, la Fig. 4 montre la fa ç on CORRECTE de couper l ’ extr é mit é de la planche, et la Fig.
Fran ç ais 30 SERVICE APRES-VENTE ET REPARATIONS Tous les outils motoris é s de qualit é auront é ventuellement besoin d ’ une r é paration ou du remplacement d ’ une pi è ce à cause de l ’ usure normale de l ’ outil.
Fran ç ais 31 UTILISATION D ’ UN CORDON DE RALLONGE Utiliser exclusivement un cordon de rallonge en bon é tat. Lorsqu ’ on utilise un cordon de rallonge, veiller à ce qu ’ il soit suffisamment lourd pour supporter le courant dont l ’ appareil aura besoin.
Fran ç ais 32 DOUBLE ISOLATION POUR UN FONCTIONNEMENT PLUS SUR Pour assurer un fonctionnement plus s û r de cet outil motoris é , HITACHI a adopt é une conception à double insolation.
Fran ç ais 33 DESCRIPTION FONCTIONNELLE REMARQUE: Les informations contenues dans ce mode d ’ emploi sont con ç ues pour assister l ’ utilisateur dans une utilisation sans danger et un entretien de l ’ outil motoris é .
Fran ç ais 34 ASSEMBLAGE ET FONCTIONNEMENT APPLICATIONS 䡬 Coupe de fibro-ciment (Ex. Planche HARDI, Panneau HARDI) AVANT L ’ UTILISATION 1. Source d ’ alimentation S ’ assurer que la source d.
Fran ç ais 35 7. V é rifier si le levier de serrage et le boulon à ailettes sont bien serr é s. Si le boulon à ailettes pour le r é glage de la profondeur de coupe (Fig. 12) et le boulon à ailettes pour le r é glage de l ’ angle d ’ inclinaison (Fig.
Fran ç ais 36 descente maximale. Si l ’ on utilise l ’ outil dans sa position de montage d ’ origine pour une coupe à angle doit, cela permettra de r é duire l ’é parpillement des particules de sciure.
Fran ç ais 37 Il est possible de r é gler la position de coupe en d é pla ç ant le guide vers la gauche ou vers la droite apr è s avoir desserr é son boulon à ailettes. Le guide pourra ê tre mont é sur le c ô t é droit ou sur le c ô t é gauche de l ’ outil.
Fran ç ais 38 1. Marquer bien lisiblement la section à couper avec des lignes sur tous les c ô t é s. (Voir Fig. 16) 2. R é gler la profondeur de coupe en fonction du mat é riau à couper. 3. Pousser le levier du carter de s é curit é à fond vers l ’ arri è re jusqu ’à ce que la lame soit expos é e, comme indiqu é à la Fig.
Fran ç ais 39 (3) Pour s ’ assurer que la lame tourne dans le bon sens, il faut que la fl è che de la lame soit dirig é e dans le m ê me sens que celle du carter de lame. (4) Avec les doigts, serrer le boulon hexagonal qui fixe la lame de scie au maximum.
Fran ç ais 40 Fig. 22 Fig. 21 UTILISATION DU GUIDE-POUSSI È RE AVERTISSEMENT : ● Pour é viter tout risque d ’ accident grave, s ’ assurer que l ’ interrupteur est à la position OFF et d é brancher la fiche de la prise secteur.
Fran ç ais 41 Fig. 24 ENTRETIEN ET INSPECTION AVERTISSEMENT: Pour é viter tout risque d ’ accident grave, s ’ assurer que l ’ interrupteur est à la position OFF et d é brancher la fiche de la prise secteur.
Fran ç ais 42 Equerre Socle Vis de fixation fendue Fig. 25 (1) Retourner le socle (Fig. 25) et desserrer l ’é crou à oreilles. (2) Placer une é querre entre le socle et la lame de scie et d é placer la position du socle en tournant la vis de fixation fendue avec un tournevis à lame plate de fa ç on à obtenir un angle droit.
Fran ç ais 43 ACCESSOIRES AVERTISSEMENT : Les accessoires pour cet outil motoris é sont mentionn é s dans ce mode d ’ emploi. L ’ utilisation de toute autre fixation ou accessoire peut ê tre dangereux et causer des blessures ou des dommages m é caniques.
Español 44 INFORMACIÓN IMPORTANTE Antes de utilizar o realizar cualquier trabajo de mantenimiento de esta herramienta eléctrica, lea y comprenda todas las instrucciones de operación, las precauciones de seguridad, y las advertencias de este Manual de instrucciones.
Espa ñ ol 45 SEGURIDAD NORMAS DE SEGURIDAD ADVERTENCIA: La utilizaci ó n inadecuada de las herramientas el é ctricas puede resultar en lesiones serias o en la muerte. Para evitar estos riesgos, siga las instrucciones de seguridad ofrecidas a continuaci ó n.
Espa ñ ol 46 No utilice las herramientas el é ctricas donde haya l í quidos o gases inflamables. Las herramientas el é ctricas producen chispas durante su funcionamiento. Tambi é n producir á n chispas cuando conecte/desconecte su alimentaci ó n.
Espa ñ ol 47 21. PRESTE ATENCI Ó N. Preste atenci ó n a lo que est é haciendo. Utilice el sentido com ú n. No utilice ninguna herramienta cuando est é cansado. Usted no deber á utilizar ninguna herramienta cuando est é bajo la influencia del alcohol, drogas, ni medicinas que le produzca somnolencia.
Espa ñ ol 48 La utilizaci ó n e una herramienta el é ctrica con una tensi ó n superior a la nominal podr í a resultar en revoluciones anormalmente altas del motor, en el da ñ o de la herramienta, y en la quemadura del motor. 3 1 . NO UTILICE NUNCA UNA HERRAMIENTA DEFECTUOSA O QUE FUNCIONE ANORMALMENTE.
Espa ñ ol 49 Para evitar el contragolpe, apoye la tabla No apoye la tabla o el panel lejos o el panel cerca del lugar de corte. del lugar de corte. Fig. 1 Fig. 2 40. UTILICE UNA ESCUADRA DE GU Í A. Siempre utilice una escuadra de gu í a o una regla como gu í a para cortar al largo.
Espa ñ ol 50 43. PROTECTOR INFERIOR. Levante el protector inferior con la empu ñ adura retr á ctil. 44. AJUSTES. Antes de ajustar, aseg ú rese de que los ajustes de profundidad y biselado est é n bien hechos. 45. UTILICE UNICAMENTE LAS CUCHILLAS CORRECTAS PARA EL MONTAJE.
Espa ñ ol 51 52. No intente nunca cortar colocando la sierra circular de manera invertida sobre un banco de trabajo. Esto es sumamente peligroso y puede producir accidentes de gravedad.
Espa ñ ol 52 UTILIZACI Ó N DE UN CABLE PROLONGADOR Cerci ó rese de que el cable prolongador est é en buenas condiciones. Cuando utilice un cable prolongador, cerci ó rese de que tenga el calibre (grosor) suficiente como para poder conducir la corriente necesaria para la herramienta.
Espa ñ ol 53 AISLAMIENTO DOBLE PARA OFRECER UNA OPERACI Ó N M Á S SEGURA Para garantizar una operaci ó n m á s segura de esta herramienta el é ctrica, HITACHI ha adoptado un dise ñ o de aislamiento doble.
Espa ñ ol 54 DESCRIPCI Ó N FUNCTIONAL NOTA: La informaci ó n contenida en este Manual de instrucciones ha sido dise ñ ada para ayudarle a utilizar con seguridad y mantener esta herramienta el é ctrica.
Espa ñ ol 55 MONT AJE Y OPERACI Ó N APLICACIONES 䡬 Corte de una tabla de fibrocemento (Ej. HARDI PLANK, HARDI PANEL) ANTES DE LA OPERACI Ó N 1. Fuente de alimentaci ó n Cerci ó rese de que la fuente de alimentaci ó n que vaya a utilizar cumpla los requisitos indicados en la placa de caracter í sticas del producto.
Espa ñ ol 56 PRECAUCI Ó N: Para evitar accidentes, aseg ú rese siempre de que la parte de la pieza de trabajo que queda despu é s del corte est é firmemente fijada. 7. Verifique que la palanca de apriete y el perno de mariposa est é n apretados.
Espa ñ ol 57 de la hoja, o en el caso del corte inclinado o cuando utiliza la gu í a para el corte, afloje el tornillo, mueva la cubierta deslizante hacia arriba y realice los ajustes necesarios antes del uso. (Para el corte inclinado, fije la cubierta deslizante en la posici ó n m á s elevada).
Espa ñ ol 58 NOTA: Cuando instale la gu í a, mueva la cubierta deslizante hacia arriba hasta un punto en que la gu í a no contacte con la cubierta deslizante.
Espa ñ ol 59 1. Marque claramente el á rea de corte deseada con l í neas en todos los lados. (Consulte la Fig. 16.) 2. Ajuste la profundidad seg ú n el material que vaya a cortar. 3. Empuje la palanca de la cubierta de seguridad completamente hacia atr á s para que la cuchilla quede expuesta como se muestra en la Fig.
Espa ñ ol 60 (2) Para montar la cuchilla de la sierra, los lados c ó ncavos de ambas arandelas, (A) y (B), deber á n colocarse en los lados de la cuchilla de la sierra. Monte la cuchilla de la sierra en el husillo y fije finalmente la arandela (B) (consulte la Fig.
Espa ñ ol 61 Fig. 22 Fig. 21 USO DE LA GUIA PARA EL POLVO ADVERTENCIA: ● Para evitar accidentes de gravedad, aseg ú rese de que el interruptor est é en la posici ó n OFF, y extraiga el enchufe del tomacorriente.
Espa ñ ol 62 Fig. 24 MANTENIMIENTO E INSPECCI Ó N ADVERTENCIA: Para evitar accidentes de gravedad, aseg ú rese de que el interruptor est é en la posici ó n OFF, y extraiga el enchufe del tomacorriente.
Espa ñ ol 63 (1) Gire la cara de la base hacia arriba (Fig. 25) y afloje la tuerca de mariposa. (2) Aplique una escuadra a la base y la hoja de sierra y, girando el tornillo de sujeci ó n ranurado con un destornillador de punta plana, desplace la posici ó n de la base hasta conseguir un á ngulo recto.
Espa ñ ol 64 ACCESSOIRES ADVERTENCIA: Los accesorios para esta herramienta el é ctrica se mencionan en este Manual de instrucciones. La utilizaci ó n de otros accesorios puede resultar peligrosa y causar lesiones o da ñ os mec á nicos. NOTA: Las especificaciones est á n sujetas a cambio sin ninguna obligaci ó n por parte de HITACHI.
65.
66.
67 1 982-027 1 HK1010 2 302-436 1 3 302-433 1 4 992-013 2 M5 × 14 5 600-3VV 1 6003VVCMPS2L 6 319-524 1 7 961-807 1 8 319-291 1 9 319-523 1 10 319-292 1 11 958-523 2 M4 × 8 12 302-435 1 13 990-430 2 M4 × 10 14 302-443 1 15 302-423 1 16 302-427 1 M8 × 15.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construc- tion activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
An important point after buying a device Hitachi C 7YA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hitachi C 7YA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hitachi C 7YA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hitachi C 7YA you will learn all the available features of the product, as well as information on its operation. The information that you get Hitachi C 7YA will certainly help you make a decision on the purchase.
If you already are a holder of Hitachi C 7YA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hitachi C 7YA.
However, one of the most important roles played by the user manual is to help in solving problems with Hitachi C 7YA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hitachi C 7YA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
