Instruction/ maintenance manual of the product C 10LA Hitachi
Go to page of 29
English M odel Modèle Modelo Stationary Table Saw Scie sur table Sierra de mesa fi ja C 10LA INSTRUCTION MANUAL AND SAFETY INSTRUCTIONS I mproper and unsafe use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety.
– 2 – English CONTENTS SECTION PAGE SECTION PAGE Product Specifi cations ........................................ 3 Know Your Table Saw ........................................ 9 Power Tool Safety .............................................. 4 Glossary of Terms .
– 3 – English WARNING Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.
– 4 – English POWER TOOL SAFETY WARNING Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury or damage to the table saw. Good safety practices are a combination of common sense, staying alert and understanding how to use your power tool.
– 5 – English TABLE SAW SAFETY 1. ALWAYS USE SAW BLADE GUARD, splitter and antikickback pawls for every operation for which they can be used, including through sawing. Through sawing operations are those in which the blade cuts completely through the workpiece when ripping or crosscutting.
– 6 – English DO NOT MODIFY THE PLUG PROVIDED. If it will not fi t the receptacle, have the proper receptacle installed by a qualifi ed electrician.
– 7 – English U N PACKING AND CHECKING CONTENTS Separate all parts from packing materials. Check each part with the illustration on the next page and the “Table of Loose Parts” to make certain all items are accounted for, before discarding any packing material.
– 8 – English UNPACKING YOUR STATIONARY TABLE SAW A D B C E F G H I J K L M N O P Q R.
– 9 – English Blade guard Rip fence Miter gauge ON/OFF switch with key Blade elevation handwheel Table Insert Table extension (Left) Table extension (Left) Blade tilting handwheel Table extension .
– 10 – English HITACHI PROFESSIONAL TABLE SAW TERMS MITER GAUGE – A guide used for crosscutting operations that slides in the tabletop channels located on either side of the blade. It helps make accurate straight or angle cuts. RIP FENCE – A guide used for rip cutting that clamps to the tabletop.
– 11 – English 4. Adjust the mounting bolts (2) until the extension is fl ush with the saw table. Tighten. 5. Repeat these procedures for the right extension table. Fig. B ASSEMBLY THE FRONT AND REAR TABLE RAIL (FIG. B-1, B-2) NOTE: Front of table rails assemblies are different.
– 12 – English BLADE RAISING HANDWHEEL (FIG. D) Thread the blade handwheel handle (1) into blade raising handwheel (2) and tighten. BLADE TILTING HANDWHEEL (FIG. D) 1. Attach the blade tilt ing handwheel (3) to the elev ation screw at the front of the saw.
– 13 – English Fig. E Removing the blade guard assembly (Fig. E) To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnected from the power source outlet. 1. Remove the table insert. 2. With the blade elevation handwheel (2), raise the blade to the maximum height.
– 14 – English INSTALLING A BLADE (FIG. G) To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnected from the power source outlet. 1. Place the blade onto the arbor with the blade teeth pointing forward to the front of the saw.
– 15 – English ADJUSTING THE 90 O AND 45 O POSITIVE STOPS (FIG. H, H-1, I) Your saw has positive stops that will quickly position the saw blade at 90 ° and 45° to t he table. Make adjustments only if necessary. 90 O Stop (Fig. H, H-1) 1. Disconnect the saw from the power source.
– 16 – English Power Cord (FIG. M) For convenience and to prevent damage to the power cord when the table saw is not in use or is being transported, the frame of leg has two brackets (1) on the side for cord storage. Fig. M MITER GAUGE ADJUSTMENT (FIG.
– 17 – English RIP FENCE ADJUSTMENT (FIG. O) 1. For adjustments, position the fence to the right of the blade, parallel with the miter gauge groove. 2. Place the rear clamp (1) (Fig. P) of the fence on the back rail of the table, and lower the front end over the front rail (2).
– 18 – English OPERATION BASIC SAW OPERATIONS RAISE THE BLADE (FIG. R) To raise or lower the blade, turn the blade elevation handwheel (1) to the desired blade height, and then tighten the bevel lock knob (2) to maintain the desired blade angle. Fig.
– 19 – English CUTTING OPERATIONS There are two basic types of cuts: ripping and crosscutting. Ripping is cutting along the length and the grain of the workpiece. Crosscutting is cutting either across the width or across the grain of the workpiece.
– 20 – English CROSSCUTTING (FIG. V) To prevent serious injury: • Do not allow familiarity or frequent use of your table saw to cause careless mistakes. Remember that even a careless fraction of a second is enough to cause a severe injury. • Keep both hands away from the blade and the path of the blade.
– 21 – English COMPOUND MITER CROSSCUTTING (FIG. Y) This sawing operation is combining a miter angle with a bevel angle. Always work to the right side of the blade during this type of cut.
– 22 – English 2 1 3 Attach auxiliary fence to rip fence with two “C” clamps. (Fig. CC) Fig. CC DADO CUTS (FIG. DD) 1. The dado blade insert is included with this saw. Remove the saw blade, original table insert and blade guard. Install the dado and dado blade insert.
– 23 – English MAIN TENANCE MAINTAINING YOUR TABLE SAW GENERAL MAINTENANCE For your own safety, turn the switch OFF and remove the switch key. Remove the plug from the power source outlet before maintaining or lubricating your saw. 1. Clean out all sawdust that has accumulated inside the saw cabinet and the motor.
– 24 – English TROUBLESHOOTING GUIDE WARNING To avoid injury from an accidental start, turn the switch OFF and always remove the plug from the power source before making any adjustments. • Consult Hitachi Authorized Service Center if for any reason the motor will not run.
– 25 – English PUSH STICK CONSTRUCTION ● This is a full-size drawing (actual size) ● Use good quality plywood or solid wood ● Use 1/2 in. or 3/4 in. material ● Push stick MUST be thinner than the width of material being cut Drill Hole For Hanging Notch To Prevent Hand From Slipping Cut Here To Push 1/2 in.
– 72 – English PARTS LIST 10” STATIONARY TABLE SAW MODEL NO. C10LA PARTS LIST FOR SCHEMATIC HKU# I.D. No Description Size Qty HKU# I.D. No Description Size Qty 726436 09HZ SPINDLE PULLEY 2 72671.
– 73 – English 10” STATIONARY TABLE SAW MODEL NO. C10LA SCHEMATIC.
– 74 – Black Black 120V 60HZ Power Rocker Switch White White Blue Black Brown (T erminal Block) Black Motor White White Black Black Black Black (CIRCUIT BREAKER SWITCH) Black (Rocker Switch) 240V .
– 75 – English Issued by Hitachi Koki Co., Ltd. Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo 108-6020, Japan Distributed by Hitachi Koki U.S.A., Ltd. 3950 Steve Reynolds Blvd. Norcross, GA 30093 Hitachi Koki Canada Co. 6395 Kestrel Road Mississaug a ON L5T 1Z5 60 3 Code No.
An important point after buying a device Hitachi C 10LA (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Hitachi C 10LA yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Hitachi C 10LA - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Hitachi C 10LA you will learn all the available features of the product, as well as information on its operation. The information that you get Hitachi C 10LA will certainly help you make a decision on the purchase.
If you already are a holder of Hitachi C 10LA, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Hitachi C 10LA.
However, one of the most important roles played by the user manual is to help in solving problems with Hitachi C 10LA. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Hitachi C 10LA along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
