Instruction/ maintenance manual of the product OFE-321 Henny Penny
Go to page of 14
Model OFE-321,322 SECTION 2. MAINTENANCE 2-1. INTRODUCTION This section provides procedures for the checkout and replacement of the various parts used within the fryer. Before replacing any parts, refer to the Troubleshooting Section. It will aid you in determining the cause of the malfunction.
Model OFE-321,322 2-4. POWER SWITCH 1. Remove electrical power supplied to fryer. To avoid electrical shock or property damage, move the POWER switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle. 2. Remove control panel.
Model OFE-321,322 2-6. I/O POWER SUPPLY BOARD ASSEMBLY The input/output power supply board assembly distributes voltage to the various components in the fryer. The board also receives information from com ponents in the fryer. 1. Remove electrical power supplied to the unit.
Model OFE-321,322 2-7. DRAIN MICROSWITCH (Continued) 2. The following check should be made to determine if the drain microswitch is defective. a. Remove the two screws securing the microswitch to the drain rod valve bracket. b. Remove wires from the switch.
Model OFE-321,322 2-9. HEATING ELEMENTS Heating elements are available for 208 , 480 and 230 volts. Check data plate to determine correct voltage. C h e c k o u t : If the shortenings temperature recovery is very slow or at a slower rate than required, this may indicate defective heating element(s).
Model OFE-321,322 2-9. HEATING ELEMENTS (Continued) 3. Remove the heating element wires from the term inals by removing the nuts and washers. Label each so it can be replaced on the new element in the same position. 4. Remove the bolts from the five elem ent spreaders.
Model OFE-321,322 2-9. HEATING ELEMENTS (Continued) 13. Connect the power cord to the wall receptacle or close wall circuit breaker. Heating elements should never be energized without shortening in the frypot, or damage to the elements could result. 14.
Model OFE-321,322 2-10. HEATING CONTACTORS Each well of an electric fryer requires two switching contactors. The first in line is the primary contactor and the second in line is the heat contactor. When open, the primary contactor does not allow power to flow to the heat contactor.
Model OFE-321,322 2-10. HEATING Checkout (Power Supplied) CONTACTORS (Continued) To avoid electrical shock, make connections before applying power, take reading, and remove power before removing meter leads. The following checks are performed with the wall circuit breaker closed and the main power switch in the ON position.
Model OFE-321,322 2-11. SPEAKER ASSEMBLY The speaker assembly emits audible signals to let the operator know when cooking and hold times are finished. 1. Remove electrical power supplied to unit. To avoid electrical shock or property damage, move the POWER switch to OFF and disconnect main circuit breaker, or unplug cord at wall receptacle.
Model OFE-321,322 2-12. HIGH TEMPERATURE LIMIT CONTROL The electric units, models OFE-321/2/3/4, use the same high temperature control limits as the gas units, but the m ounting of the capillary tube is different on the electric units compared to the gas u n i t s .
Model OFE-321,322 2-12. HIGH TEMPERATURE LIMIT CONTROL (Continued) Be sure capillary bulb of high limit is located behind capillary bulb of thermostat. Both capillary bulbs and bulb holders should be positioned as not to interfere with basket or when cleaning the frypot wall, or damage to capillary tube could result.
Model OFE-321,322 2-13 707.
Model OFE-321,322 707 2-14.
An important point after buying a device Henny Penny OFE-321 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Henny Penny OFE-321 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Henny Penny OFE-321 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Henny Penny OFE-321 you will learn all the available features of the product, as well as information on its operation. The information that you get Henny Penny OFE-321 will certainly help you make a decision on the purchase.
If you already are a holder of Henny Penny OFE-321, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Henny Penny OFE-321.
However, one of the most important roles played by the user manual is to help in solving problems with Henny Penny OFE-321. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Henny Penny OFE-321 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
